lkml.org 
[lkml]   [2020]   [May]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 0/3] fs: reduce export usage of kerne_read*() calls
On Fri, May 22, 2020 at 03:24:32PM -0700, Scott Branden wrote:
> On 2020-05-18 5:37 a.m., Mimi Zohar wrote:
> > On Sun, 2020-05-17 at 23:22 -0700, Christoph Hellwig wrote:
> > > On Fri, May 15, 2020 at 09:29:33PM +0000, Luis Chamberlain wrote:
> > > > On Wed, May 13, 2020 at 11:17:36AM -0700, Christoph Hellwig wrote:
> > > > > Can you also move kernel_read_* out of fs.h? That header gets pulled
> > > > > in just about everywhere and doesn't really need function not related
> > > > > to the general fs interface.
> > > > Sure, where should I dump these?
> > > Maybe a new linux/kernel_read_file.h? Bonus points for a small top
> > > of the file comment explaining the point of the interface, which I
> > > still don't get :)
> > Instead of rolling your own method of having the kernel read a file,
> > which requires call specific security hooks, this interface provides a
> > single generic set of pre and post security hooks.  The
> > kernel_read_file_id enumeration permits the security hook to
> > differentiate between callers.
> >
> > To comply with secure and trusted boot concepts, a file cannot be
> > accessible to the caller until after it has been measured and/or the
> > integrity (hash/signature) appraised.
> >
> > In some cases, the file was previously read twice, first to measure
> > and/or appraise the file and then read again into a buffer for
> > use.  This interface reads the file into a buffer once, calls the
> > generic post security hook, before providing the buffer to the caller.
> >  (Note using firmware pre-allocated memory might be an issue.)
> >
> > Partial reading firmware will result in needing to pre-read the entire
> > file, most likely on the security pre hook.
> The entire file may be very large and not fit into a buffer.
> Hence one of the reasons for a partial read of the file.
> For security purposes, you need to change your code to limit the amount
> of data it reads into a buffer at one time to not consume or run out of much
> memory.

Hm? That's not how whole-file hashing works. :)

These hooks need to finish their hashing and policy checking before they
can allow the rest of the code to move forward. (That's why it's a
security hook.) If kernel memory utilization is the primary concern,
then sure, things could be rearranged to do partial read and update the
hash incrementally, but the entire file still needs to be locked,
entirely hashed by hook, then read by the caller, then unlocked and
released.

So, if you want to have partial file reads work, you'll need to
rearchitect the way this works to avoid regressing the security coverage
of these operations.

So, probably, the code will look something like:


file = kernel_open_file_for_reading(...)
file = open...
disallow_writes(file);
while (processed < size-of-file) {
buf = read(file, size...)
security_file_read_partial(buf)
}
ret = security_file_read_finished(file);
if (ret < 0) {
allow_writes(file);
return PTR_ERR(ret);
}
return file;

while (processed < size-of-file) {
buf = read(file, size...)
firmware_send_partial(buf);
}

kernel_close_file_for_reading(file)
allow_writes(file);


--
Kees Cook

\
 
 \ /
  Last update: 2020-05-23 01:06    [W:0.053 / U:1.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site