lkml.org 
[lkml]   [2020]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [EXT] Re: [PATCH v7 0/6] Add new series Micron SPI NAND devices
Date
Hi Naresh and Poonam,

> Subject: [EXT] Re: [PATCH v7 0/6] Add new series Micron SPI NAND devices
>
> Hi Poonam,
>
> Poonam Aggrwal <poonam.aggrwal@nxp.com> wrote on Fri, 15 May 2020
> 05:29:07 +0000:
>
> > Adding Ashish.
> >
> > Regards
> > Poonam
> >
> > > -----Original Message-----
> > > From: Naresh Kamboju <naresh.kamboju@linaro.org>
> > > Sent: Friday, May 15, 2020 10:57 AM
> > > To: shiva.linuxworks@gmail.com; Miquel Raynal
> <miquel.raynal@bootlin.com>;
> > > Shivamurthy Shastri <sshivamurthy@micron.com>
> > > Cc: Richard Weinberger <richard@nod.at>; Vignesh Raghavendra
> > > <vigneshr@ti.com>; Boris Brezillon <boris.brezillon@collabora.com>;
> > > Chuanhong Guo <gch981213@gmail.com>; Frieder Schrempf
> > > <frieder.schrempf@kontron.de>; linux-mtd@lists.infradead.org; open
> list <linux-
> > > kernel@vger.kernel.org>; Poonam Aggrwal
> <poonam.aggrwal@nxp.com>;
> > > Suram Suram <suram@nxp.com>; lkft-triage@lists.linaro.org
> > > Subject: Re: [PATCH v7 0/6] Add new series Micron SPI NAND devices
> > >
> > > On Wed, 11 Mar 2020 at 23:28, <shiva.linuxworks@gmail.com> wrote:
> > > >
> > > > From: Shivamurthy Shastri <sshivamurthy@micron.com>
> > > >
> > > > This patchset is for the new series of Micron SPI NAND devices, and
> > > > the following links are their datasheets.
> > >
> > > While boot NXP ls2088 device with mainline kernel the following nand
> warning
> > > noticed. How critical this warning ?
>
> Are you sure this is the right thread? Shivamurthy added SPI-NAND
> support, you are talking about a raw NAND device.
> > >
> > > [ 1.357722] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48
> > > [ 1.364085] nand: Micron MT29F16G08ABACAWP
> > > [ 1.368181] nand: 2048 MiB, SLC, erase size: 512 KiB, page size:
> > > 4096, OOB size: 224
> > > [ 1.375932] nand: WARNING: 530000000.flash: the ECC used on your
> > > system is too weak compared to the one required by the NAND chip
>
> If you are talking about this one, it is pretty self explanatory: the
> NAND chip requires a minimum correction which is not achieved here.
> Either because the ECC engine cannot reach the requested amount (you
> cannot do anything) or because you requested a too low correction with
> DT properties.
>

Minimum required ECC for this device is 8-bit. Below is the datasheet for your reference.

https://www.micron.com/-/media/client/global/documents/products/data-sheet/nand-flash/70-series/m72a_production_datasheet_revg.pdf?rev=bb0a4ba04a1f40f98e29dc624d178dd8


> > >
> > > [ 1.388767] Bad block table found at page 524160, version 0x01
> > > [ 1.396833] Bad block table found at page 524032, version 0x01
> > > [ 1.403781] nand_read_bbt: bad block at 0x000002d00000
> > > [ 1.408921] nand_read_bbt: bad block at 0x000002d80000
> > > [ 1.414750] fsl,ifc-nand 530000000.nand: IFC NAND device at
> > > 0x530000000, bank 2
> > >
> > >
> > > Full test log,
> > >
> https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fqa-
> > > reports.linaro.org%2Flkft%2Flinux-mainline-oe%2Fbuild%2Fv5.7-rc5-55-
> > >
> g1ae7efb38854%2Ftestrun%2F18254%2Flog&amp;data=02%7C01%7Cpoona
> m.
> > >
> aggrwal%40nxp.com%7C146f634c869f4c70baa108d7f8909ffb%7C686ea1d3bc
> 2
> > >
> b4c6fa92cd99c5c301635%7C0%7C0%7C637251172354638298&amp;sdata=%2B
> > >
> Jhs%2Fb92%2BA56WzYdHe%2BBhXWfjk8feCGAFv%2BRzFKC9PM%3D&amp;r
> ese
> > > rved=0
> > >
> > > - Naresh
>
> Thanks,
> Miquèl

Thanks,
Shiva
\
 
 \ /
  Last update: 2020-05-15 12:00    [W:0.057 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site