lkml.org 
[lkml]   [2020]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] ARM: dts: zynq: Fix ethernet PHY for v5 schematics
Hi Anton,

I hope you are doing good. Could you please check this patch, since
you are initial author of zynq-zturn.dts and I suppose you do have the
"v4" board variant to test.

вт, 28 апр. 2020 г. в 13:04, Matwey V. Kornilov <matwey@sai.msu.ru>:
>
> There are at least two different versions existing for MYIR Zturn:
>
> * v4 schematics has Atheros AR8035 PHY at 0b000
> http://www.myirtech.com/download/Zynq7000/Z-TURNBOARD_schematic.pdf
> * v5 schematics has Micrel KSZ9031 PHY at 0b011
> v5 schematics available at DVD disk supplied with the board
>
> Specify both PHYs to make ethernet interface working for any board
> revision. This commit relies on of_mdiobus_register() behavior.
> When phy-handle is missed, every nested PHY node is considered,
> while ENODEVs are ignored.
>
> Before the patch:
>
> [ 28.295002] macb e000b000.ethernet eth0: Could not attach PHY (-19)
>
> After the patch:
>
> [ 28.257365] macb e000b000.ethernet eth0: PHY [e000b000.ethernet-ffffffff:00] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL)
> [ 28.257384] macb e000b000.ethernet eth0: configuring for phy/rgmii-id link mode
>
> Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>

Cc: Anton Gerasimov <tossel@gmail.com>

> ---
> Changes since v1:
> - reworded commit message
>
> arch/arm/boot/dts/zynq-zturn.dts | 13 ++++++++++---
> 1 file changed, 10 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/zynq-zturn.dts b/arch/arm/boot/dts/zynq-zturn.dts
> index 5ec616ebca08..07da9cf60d02 100644
> --- a/arch/arm/boot/dts/zynq-zturn.dts
> +++ b/arch/arm/boot/dts/zynq-zturn.dts
> @@ -67,10 +67,17 @@
> &gem0 {
> status = "okay";
> phy-mode = "rgmii-id";
> - phy-handle = <&ethernet_phy>;
>
> - ethernet_phy: ethernet-phy@0 {
> - reg = <0x0>;
> + ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + max-speed = <1000>;
> + };
> +
> + ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <3>;
> + max-speed = <1000>;
> };
> };
>
> --
> 2.16.4
>


--
With best regards,
Matwey V. Kornilov

\
 
 \ /
  Last update: 2020-05-01 18:11    [W:0.061 / U:0.764 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site