Messages in this thread | | | Date | Fri, 03 Apr 2020 16:45:49 +0530 | From | kgunda@codeauro ... | Subject | Re: [PATCH V4 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format |
| |
On 2020-03-31 23:24, Rob Herring wrote: > On Mon, Mar 23, 2020 at 11:16:55PM +0530, Kiran Gunda wrote: >> Convert the qcom-wled bindings from .txt to .yaml format. >> >> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> >> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org> >> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> >> --- >> .../bindings/leds/backlight/qcom-wled.txt | 154 >> ----------------- >> .../bindings/leds/backlight/qcom-wled.yaml | 184 >> +++++++++++++++++++++ >> 2 files changed, 184 insertions(+), 154 deletions(-) >> delete mode 100644 >> Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt >> create mode 100644 >> Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml > >> diff --git >> a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml >> b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml >> new file mode 100644 >> index 0000000..8a388bf >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml >> @@ -0,0 +1,184 @@ >> +# SPDX-License-Identifier: GPL-2.0-only >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Binding for Qualcomm Technologies, Inc. WLED driver >> + >> +maintainers: >> + - Lee Jones <lee.jones@linaro.org> > > Should be the h/w owner (you), not who applies patches. > will address in next post. >> + >> +description: | >> + WLED (White Light Emitting Diode) driver is used for controlling >> display >> + backlight that is part of PMIC on Qualcomm Technologies, Inc. >> reference >> + platforms. The PMIC is connected to the host processor via SPMI >> bus. >> + >> +properties: >> + compatible : > > Drop the space ^ > will address in next post. >> + enum: >> + - qcom,pm8941-wled >> + - qcom,pmi8998-wled >> + - qcom,pm660l-wled > > Wrong indent (1 space too many). > will address in next post. >> + >> + reg: >> + maxItems: 1 >> + >> + default-brightness: >> + maxItems: 1 > > maxItems is for arrays and this is a single scalar. > >> + description: >> + brightness value on boot, value from 0-4095. > > 0-4095 sounds like a constraint. > will address in next post. >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 > > There should be a common definition for this. > will address in next post. >> + default: 2048 >> + >> + label: >> + maxItems: 1 >> + description: >> + The name of the backlight device. >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/string > > Already has a type. Just 'label: true' is enough. > will address in next post. >> + >> + qcom,cs-out: >> + description: >> + enable current sink output. >> + This property is supported only for PM8941. >> + type: boolean >> + >> + qcom,cabc: >> + description: >> + enable content adaptive backlight control. >> + type: boolean >> + >> + qcom,ext-gen: >> + description: >> + use externally generated modulator signal to dim. >> + This property is supported only for PM8941. >> + type: boolean >> + >> + qcom,current-limit: >> + maxItems: 1 > > Not an array. > will address in next post. >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + mA; per-string current limit; value from 0 to 25 with > > 25 sounds like a constraint. > will address in next post. >> + 1 mA step. This property is supported only for pm8941. >> + default: 20 >> + >> + qcom,current-limit-microamp: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 > > properties with unit suffix already have a type. > will address in next post. >> + description: >> + uA; per-string current limit; value from 0 to 30000 with >> + 2500 uA step. > > steps can be expressed using 'multipleOf' > will address in next post. >> + default: 25 > > 25 can never be a multiple of 2500 > will correct in next post. >> + >> + qcom,current-boost-limit: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + mA; boost current limit. >> + For pm8941 one of 105, 385, 525, 805, 980, 1260, 1400, 1680. >> + Default, 805 mA. >> + For pmi8998 one of 105, 280, 450, 620, 970, 1150, 1300, >> + 1500. Default 970 mA. > > Constraints. > will address in next post. >> + >> + qcom,switching-freq: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + kHz; switching frequency; one of 600, 640, 685, 738, >> + 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, >> + 4800, 9600. >> + Default for pm8941 1600 kHz >> + for pmi8998 800 kHz > > Constraints! > will address in next post. >> + >> + qcom,ovp: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + V; Over-voltage protection limit; one of 27, 29, 32, 35. >> Default 29V >> + This property is supported only for PM8941. >> + >> + qcom,ovp-millivolt: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + mV; Over-voltage protection limit; >> + For pmi8998 one of 18100, 19600, 29600, 31100. >> + Default 29600 mV. >> + If this property is not specified for PM8941, it >> + falls back to "qcom,ovp" property. >> + >> + qcom,num-strings: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + number of led strings attached; >> + value for PM8941 from 1 to 3. Default 2 >> + For PMI8998 from 1 to 4. >> + >> + interrupts: >> + maxItems: 2 > > items: > - description: ... > - description: ... > will address in next post. >> + description: >> + Interrupts associated with WLED. This should be >> + "short" and "ovp" interrupts. Interrupts can be >> + specified as per the encoding listed under >> + Documentation/devicetree/bindings/spmi/ >> + qcom,spmi-pmic-arb.txt. > > encoding is outside the scope of the binding. > will address in next post. >> + >> + interrupt-names: >> + description: >> + Interrupt names associated with the interrupts. >> + Must be "short" and "ovp". The short circuit detection >> + is not supported for PM8941. > > Names should be constraints. > will address in next post. >> + >> + qcom,enabled-strings: >> + maxItems: 1 >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32-array >> + description: >> + Array of the WLED strings numbered from 0 to 3. Each >> + string of leds are operated individually. Specify the >> + list of strings used by the device. Any combination of >> + led strings can be used. >> + >> + qcom,external-pfet: >> + description: >> + Specify if external PFET control for short circuit >> + protection is used. This property is supported only >> + for PMI8998. >> + type: boolean >> + >> + qcom,auto-string-detection: >> + description: >> + Enables auto-detection of the WLED string configuration. >> + This feature is not supported for PM8941. >> + type: boolean >> + >> +required: >> + - compatible >> + - reg >> + - label >> + >> +examples: >> + - | >> + pm8941-wled@d800 { > > backlight@... > will add in next post. >> + compatible = "qcom,pm8941-wled"; >> + reg = <0xd800 0x100>; >> + label = "backlight"; >> + >> + qcom,cs-out; >> + qcom,current-limit = <20>; >> + qcom,current-boost-limit = <805>; >> + qcom,switching-freq = <1600>; >> + qcom,ovp = <29>; >> + qcom,num-strings = <2>; >> + qcom,enabled-strings = <0 1>; >> + }; >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora >> Forum, >> a Linux Foundation Collaborative Project >>
| |