lkml.org 
[lkml]   [2020]   [Apr]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH] iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger
On Sun, Apr 26, 2020 at 10:22 PM Srinivas Pandruvada
<srinivas.pandruvada@linux.intel.com> wrote:
>
> On Sat, 2020-04-25 at 07:22 +0000, Ardelean, Alexandru wrote:
> > On Sat, 2020-04-25 at 06:28 +0000, Ardelean, Alexandru wrote:
> > > [External]
> > >
> > > On Fri, 2020-04-24 at 14:31 -0700, Srinivas Pandruvada wrote:
> > > > [External]
> > > >
> > > > On Fri, 2020-04-24 at 07:34 +0300, Alexandru Ardelean wrote:
> > > > > The main intent here is to get rid of the
> > > > > iio_buffer_set_attrs()
> > > > > helper, or
> > > > > at least rework it's usage a bit.
> > > > > The problem with that helper is that it needs a pointer to the
> > > > > buffer,
> > > > > which makes supporting multiple buffers per IIO device a bit
> > > > > more
> > > > > cumbersome.
> > > > >
> > > > > The hid_sensor_setup_trigger() is pretty much used in the same
> > > > > way:
> > > > > - iio_triggered_buffer_setup() gets called before
> > > > > - then hid_sensor_setup_trigger() and
> > > > > hid_sensor_setup_batch_mode()
> > > > > gets
> > > > > called which may attach some fifo attributes
> > > > >
> > > > > This change merges the 2 together under the
> > > > > hid_sensor_setup_trigger()
> > > > > function. Only the &iio_pollfunc_store_time is passed to all
> > > > > devices,
> > > > > so
> > > > > it's not even required to pass it explicitly outside of the
> > > > > common
> > > > > hid_sensor_setup_trigger() function.
> > > > >
> > > > > Moving the devm_iio_triggered_buffer_setup/cleanup() calls into
> > > > > the
> > > > > common
> > > > > place code can help the rework of the buffer code, since it is
> > > > > in one
> > > > > place.
> > > > >
> > > > > One detail of the change is that there are 2 drivers that use
> > > > > devm_iio_triggered_buffer_setup(). That function gets
> > > > > implicitly
> > > > > replaced with iio_triggered_buffer_setup()/cleanup(), but since
> > > > > all
> > > > > drivers
> > > > > call both hid_sensor_setup_trigger9) &
> > > > > hid_sensor_remove_trigger()
> > > > > trigger,
> > > > > the iio_triggered_buffer_cleanup() piggy backs on the
> > > > > hid_sensor_remove_trigger() call, which should cover the
> > > > > cleanup.
> > > >
> > > > Did you test on any platform? You can check any later laptops and
> > > > check
> > > > display rotation.
> > >
> > > Sorry, I didn't.
> > > I do remember seeing this on some smaller tablet-laptops, but I
> > > don't have one
> > > around.
> > > The newest I have is Dell Precision 5520 from 2 years ago. Which is
> > > more of an
> > > office laptop.
> > >
> > > I can't seem to find any IIO devices on it.
> > > So, I don't think it has any display rotation; on Windows I'm
> > > pretty sure I
> > > didn't see anything about.
> > >
> >
> > I should mention.
> > I'm running XUbuntu 19.10, kernel version is 5.3
> > XUbuntu is basically Ubuntu re-packaged with XFCE.
>
> Not sure about this laptop. But most of the 2-in-1s released in last 2-
> 3 years should have sensor hub in it.
> Can you check lspci -vvv?
>

Sure.

00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core
Processor Host Bridge/DRAM Registers (rev 05)
Subsystem: Dell Xeon E3-1200 v6/7th Gen Core Processor Host
Bridge/DRAM Registers
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
Kernel driver in use: skl_uncore

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th
Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: ec000000-ed0fffff [size=17M]
Prefetchable memory behind bridge:
00000000c0000000-00000000d1ffffff [size=288M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th
Gen Core Processor PCIe Controller (x16)
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00218 Data: 0000
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, Exit
Latency L0s <256ns, L1 <8us
ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s (ok), Width x16 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+,
OBFF Via WAKE# ARIFwd-
AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Via WAKE# ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Capabilities: [d94 v1] Secondary PCI Express <?>
Kernel driver in use: pcieport

00:02.0 VGA compatible controller: Intel Corporation HD Graphics 630
(rev 04) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: Dell HD Graphics 630
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 142
Region 0: Memory at eb000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [40] Vendor Specific Information: Len=0c <?>
Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-,
OBFF Not Supported
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
AtomicOpsCtl: ReqEn-
Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00018 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Process Address Space ID (PASID)
PASIDCap: Exec- Priv-, Max PASID Width: 14
PASIDCtl: Enable- Exec- Priv-
Capabilities: [200 v1] Address Translation Service (ATS)
ATSCap: Invalidate Queue Depth: 00
ATSCtl: Enable-, Smallest Translation Unit: 00
Capabilities: [300 v1] Page Request Interface (PRI)
PRICtl: Enable- Reset-
PRISta: RF- UPRGI- Stopped+
Page Request Capacity: 00008000, Page Request Allocation: 00000000
Kernel driver in use: i915
Kernel modules: i915

00:04.0 Signal processing controller: Intel Corporation Xeon E3-1200
v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem (rev 05)
Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor
Thermal Subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at edd20000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: proc_thermal
Kernel modules: processor_thermal_device

00:14.0 USB controller: Intel Corporation 100 Series/C230 Series
Chipset Family USB 3.0 xHCI Controller (rev 31) (prog-if 30 [XHCI])
Subsystem: Dell 100 Series/C230 Series Chipset Family USB 3.0 xHCI
Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 128
Region 0: Memory at edd10000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee00338 Data: 0000
Kernel driver in use: xhci_hcd

00:14.2 Signal processing controller: Intel Corporation 100
Series/C230 Series Chipset Family Thermal Subsystem (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Thermal Subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at edd39000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal

00:15.0 Signal processing controller: Intel Corporation 100
Series/C230 Series Chipset Family Serial IO I2C Controller #0 (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Serial IO
I2C Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at edd38000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vendor Specific Information: Len=14 <?>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci

00:15.1 Signal processing controller: Intel Corporation 100
Series/C230 Series Chipset Family Serial IO I2C Controller #1 (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Serial IO
I2C Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at edd37000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vendor Specific Information: Len=14 <?>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci

00:16.0 Communication controller: Intel Corporation 100 Series/C230
Series Chipset Family MEI Controller #1 (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family MEI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 140
Region 0: Memory at edd36000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee004d8 Data: 0000
Kernel driver in use: mei_me
Kernel modules: mei_me

00:16.3 Serial controller: Intel Corporation 100 Series/C230 Series
Chipset Family KT Redirection (rev 31) (prog-if 02 [16550])
Subsystem: Dell 100 Series/C230 Series Chipset Family KT Redirection
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin D routed to IRQ 19
Region 0: I/O ports at f0a0 [size=8]
Region 1: Memory at edd35000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: serial

00:17.0 SATA controller: Intel Corporation
Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI
Mode] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA
Controller [AHCI Mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 130
Region 0: Memory at edd30000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at edd34000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at edd33000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00378 Data: 0000
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci
Kernel modules: ahci

00:1c.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset
Family PCI Express Root Port #1 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff [empty]
Memory behind bridge: edc00000-edcfffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [empty]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 8GT/s, Width x1, ASPM L1, Exit
Latency L1 <16us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Not Supported ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00238 Data: 0000
Capabilities: [90] Subsystem: Dell 100 Series/C230 Series Chipset
Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express <?>
Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset
Family PCI Express Root Port #2 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff [size=4K]
Memory behind bridge: ed100000-edafffff [size=10M]
Prefetchable memory behind bridge:
00000000d2100000-00000000d2afffff [size=10M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 8GT/s, Width x1, ASPM L1, Exit
Latency L1 <16us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #5, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Not Supported ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00278 Data: 0000
Capabilities: [90] Subsystem: Dell 100 Series/C230 Series Chipset
Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express <?>
Kernel driver in use: pcieport

00:1d.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset
Family PCI Express Root Port #9 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff [empty]
Memory behind bridge: edb00000-edbfffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [empty]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #9, Speed 8GT/s, Width x4, ASPM L1, Exit
Latency L1 <16us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s (ok), Width x4 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #12, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Not Supported ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00298 Data: 0000
Capabilities: [90] Subsystem: Dell 100 Series/C230 Series Chipset
Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express <?>
Kernel driver in use: pcieport

00:1d.4 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset
Family PCI Express Root Port #13 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 126
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff [empty]
Memory behind bridge: fff00000-000fffff [empty]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [empty]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #13, Speed 8GT/s, Width x2, ASPM L0s L1, Exit
Latency L0s unlimited, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x0 (downgraded)
TrErr- Train+ SlotClk+ DLActive- BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Via WAKE# ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee002b8 Data: 0000
Capabilities: [90] Subsystem: Dell 100 Series/C230 Series Chipset
Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: pcieport

00:1d.6 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset
Family PCI Express Root Port #15 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 127
Bus: primary=00, secondary=06, subordinate=3e, sec-latency=0
I/O behind bridge: 00002000-00002fff [size=4K]
Memory behind bridge: d4000000-ea0fffff [size=353M]
Prefetchable memory behind bridge:
0000000090000000-00000000b1ffffff [size=544M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #15, Speed 8GT/s, Width x2, ASPM not supported
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x0 (downgraded)
TrErr- Train+ SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #18, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Not Supported ARIFwd+
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee002f8 Data: 0000
Capabilities: [90] Subsystem: Dell 100 Series/C230 Series Chipset
Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
RootCmd: CERptEn+ NFERptEn+ FERptEn+
RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express <?>
Kernel driver in use: pcieport

00:1f.0 ISA bridge: Intel Corporation CM238 Chipset LPC/eSPI Controller (rev 31)
Subsystem: Dell CM238 Chipset LPC/eSPI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:1f.2 Memory controller: Intel Corporation 100 Series/C230 Series
Chipset Family Power Management Controller (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family Power
Management Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at edd2c000 (32-bit, non-prefetchable) [disabled]
[size=16K]

00:1f.3 Audio device: Intel Corporation CM238 HD Audio Controller (rev
31) (prog-if 80)
Subsystem: Dell CM238 HD Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin B routed to IRQ 143
Region 0: Memory at edd28000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at edd00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00518 Data: 0000
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel

00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset Family
SMBus (rev 31)
Subsystem: Dell 100 Series/C230 Series Chipset Family SMBus
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at edd32000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801

01:00.0 3D controller: NVIDIA Corporation GM107GLM [Quadro M1200
Mobile] (rev a2)
Subsystem: Dell GM107GLM [Quadro M1200 Mobile]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [disabled] [size=128]
Expansion ROM at ed000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 75.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit
Latency L0s <1us, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s (ok), Width x16 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR+, OBFF
Via message
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [250 v1] Latency Tolerance Reporting
Max snoop latency: 71680ns
Max no snoop latency: 71680ns
Capabilities: [258 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
L1_PM_Substates+
PortCommonModeRestoreTime=255us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1
Len=024 <?>
Capabilities: [900 v1] Secondary PCI Express <?>
Kernel modules: nvidiafb, nouveau, nvidia_drm, nvidia

02:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78)
Subsystem: Intel Corporation Wireless 8265 / 8275
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 141
Region 0: Memory at edc00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee004f8 Data: 0000
Capabilities: [40] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Exit
Latency L1 <8us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via WAKE#
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Device Serial Number d4-25-8b-ff-ff-ea-6a-b9
Capabilities: [14c v1] Latency Tolerance Reporting
Max snoop latency: 3145728ns
Max no snoop latency: 3145728ns
Capabilities: [154 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
L1_PM_Substates+
PortCommonModeRestoreTime=30us PortTPowerOnTime=18us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=60us
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi

03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd.
RTS525A PCI Express Card Reader (rev 01)
Subsystem: Dell RTS525A PCI Express Card Reader
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 129
Region 1: Memory at ed100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00358 Data: 0000
Capabilities: [b0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 10.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR+,
OBFF Via message/WAKE#
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [148 v1] Device Serial Number 00-00-00-01-00-4c-e0-00
Capabilities: [158 v1] Latency Tolerance Reporting
Max snoop latency: 3145728ns
Max no snoop latency: 3145728ns
Capabilities: [160 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
L1_PM_Substates+
PortCommonModeRestoreTime=60us PortTPowerOnTime=60us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=60us
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci

04:00.0 Non-Volatile memory controller: Toshiba America Info Systems
Device 0116 (prog-if 02 [NVM Express])
Subsystem: Toshiba America Info Systems Device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: Memory at edb00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
SlotPowerLimit 25.000W
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit
Latency L1 <32us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s (ok), Width x4 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR+, OBFF
Not Supported
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [b0] MSI-X: Enable+ Count=32 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [260 v1] Latency Tolerance Reporting
Max snoop latency: 3145728ns
Max no snoop latency: 3145728ns
Capabilities: [300 v1] Secondary PCI Express <?>
Capabilities: [400 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
L1_PM_Substates+
PortCommonModeRestoreTime=60us PortTPowerOnTime=100us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=100us
Kernel driver in use: nvme
Kernel modules: nvme



>
> Thanks,
> Srinivas
>
> >
> >
> > > Maybe I missed it.
> > > Any pointers are appreciated.
> > >
> > > Thanks
> > > Alex
> > >
> > > > Thanks,
> > > > Srinivas
> > > >
> > > > > Signed-off-by: Alexandru Ardelean <
> > > > > alexandru.ardelean@analog.com>
> > > > > ---
> > > > > drivers/iio/accel/hid-sensor-accel-3d.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > .../common/hid-sensors/hid-sensor-trigger.c | 18
> > > > > +++++++++++++++-
> > > > > --
> > > > > .../common/hid-sensors/hid-sensor-trigger.h | 3 ++-
> > > > > drivers/iio/gyro/hid-sensor-gyro-3d.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/humidity/hid-sensor-humidity.c | 12 +++-------
> > > > > --
> > > > > drivers/iio/light/hid-sensor-als.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/light/hid-sensor-prox.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/magnetometer/hid-sensor-magn-3d.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/orientation/hid-sensor-incl-3d.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/orientation/hid-sensor-rotation.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > drivers/iio/pressure/hid-sensor-press.c | 18 ++++----
> > > > > ------
> > > > > ----
> > > > > .../iio/temperature/hid-sensor-temperature.c | 12 +++-------
> > > > > --
> > > > > 12 files changed, 55 insertions(+), 134 deletions(-)
> > > > >
> > > > > diff --git a/drivers/iio/accel/hid-sensor-accel-3d.c
> > > > > b/drivers/iio/accel/hid-sensor-accel-3d.c
> > > > > index 0d9e2def2b25..0ec0533448bc 100644
> > > > > --- a/drivers/iio/accel/hid-sensor-accel-3d.c
> > > > > +++ b/drivers/iio/accel/hid-sensor-accel-3d.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > enum accel_3d_channel {
> > > > > @@ -391,18 +389,13 @@ static int hid_accel_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&accel_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &accel_state-
> > > > > > common_attributes);
> > > > > if (ret < 0) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -426,9 +419,7 @@ static int hid_accel_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&accel_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &accel_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -443,8 +434,7 @@ static int hid_accel_3d_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev, hsdev->usage);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&accel_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &accel_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/common/hid-sensors/hid-sensor-
> > > > > trigger.c
> > > > > b/drivers/iio/common/hid-sensors/hid-sensor-trigger.c
> > > > > index 906d87780419..ff375790b7e8 100644
> > > > > --- a/drivers/iio/common/hid-sensors/hid-sensor-trigger.c
> > > > > +++ b/drivers/iio/common/hid-sensors/hid-sensor-trigger.c
> > > > > @@ -13,6 +13,8 @@
> > > > > #include <linux/hid-sensor-hub.h>
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/trigger.h>
> > > > > +#include <linux/iio/triggered_buffer.h>
> > > > > +#include <linux/iio/trigger_consumer.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include "hid-sensor-trigger.h"
> > > > > @@ -222,7 +224,8 @@ static int
> > > > > hid_sensor_data_rdy_trigger_set_state(struct iio_trigger *trig,
> > > > > return
> > > > > hid_sensor_power_state(iio_trigger_get_drvdata(trig),
> > > > > state);
> > > > > }
> > > > >
> > > > > -void hid_sensor_remove_trigger(struct hid_sensor_common
> > > > > *attrb)
> > > > > +void hid_sensor_remove_trigger(struct iio_dev *indio_dev,
> > > > > + struct hid_sensor_common *attrb)
> > > > > {
> > > > > if (atomic_read(&attrb->runtime_pm_enable))
> > > > > pm_runtime_disable(&attrb->pdev->dev);
> > > > > @@ -233,6 +236,7 @@ void hid_sensor_remove_trigger(struct
> > > > > hid_sensor_common *attrb)
> > > > > cancel_work_sync(&attrb->work);
> > > > > iio_trigger_unregister(attrb->trigger);
> > > > > iio_trigger_free(attrb->trigger);
> > > > > + iio_triggered_buffer_cleanup(indio_dev);
> > > > > }
> > > > > EXPORT_SYMBOL(hid_sensor_remove_trigger);
> > > > >
> > > > > @@ -246,11 +250,18 @@ int hid_sensor_setup_trigger(struct
> > > > > iio_dev
> > > > > *indio_dev, const char *name,
> > > > > int ret;
> > > > > struct iio_trigger *trig;
> > > > >
> > > > > + ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > + NULL, NULL);
> > > > > + if (ret) {
> > > > > + dev_err(&indio_dev->dev, "Triggered Buffer
> > > > > Setup
> > > > > Failed\n");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > trig = iio_trigger_alloc("%s-dev%d", name, indio_dev-
> > > > > >id);
> > > > > if (trig == NULL) {
> > > > > dev_err(&indio_dev->dev, "Trigger Allocate
> > > > > Failed\n");
> > > > > ret = -ENOMEM;
> > > > > - goto error_ret;
> > > > > + goto error_triggered_buffer_cleanup;
> > > > > }
> > > > >
> > > > > trig->dev.parent = indio_dev->dev.parent;
> > > > > @@ -284,7 +295,8 @@ int hid_sensor_setup_trigger(struct iio_dev
> > > > > *indio_dev, const char *name,
> > > > > iio_trigger_unregister(trig);
> > > > > error_free_trig:
> > > > > iio_trigger_free(trig);
> > > > > -error_ret:
> > > > > +error_triggered_buffer_cleanup:
> > > > > + iio_triggered_buffer_cleanup(indio_dev);
> > > > > return ret;
> > > > > }
> > > > > EXPORT_SYMBOL(hid_sensor_setup_trigger);
> > > > > diff --git a/drivers/iio/common/hid-sensors/hid-sensor-
> > > > > trigger.h
> > > > > b/drivers/iio/common/hid-sensors/hid-sensor-trigger.h
> > > > > index f47b940ff170..bb45cc89e551 100644
> > > > > --- a/drivers/iio/common/hid-sensors/hid-sensor-trigger.h
> > > > > +++ b/drivers/iio/common/hid-sensors/hid-sensor-trigger.h
> > > > > @@ -13,7 +13,8 @@ extern const struct dev_pm_ops
> > > > > hid_sensor_pm_ops;
> > > > >
> > > > > int hid_sensor_setup_trigger(struct iio_dev *indio_dev, const
> > > > > char
> > > > > *name,
> > > > > struct hid_sensor_common
> > > > > *attrb);
> > > > > -void hid_sensor_remove_trigger(struct hid_sensor_common
> > > > > *attrb);
> > > > > +void hid_sensor_remove_trigger(struct iio_dev *indio_dev,
> > > > > + struct hid_sensor_common
> > > > > *attrb);
> > > > > int hid_sensor_power_state(struct hid_sensor_common *st, bool
> > > > > state);
> > > > >
> > > > > #endif
> > > > > diff --git a/drivers/iio/gyro/hid-sensor-gyro-3d.c
> > > > > b/drivers/iio/gyro/hid-sensor-gyro-3d.c
> > > > > index 08cacbbf31e6..7f382aae1dfd 100644
> > > > > --- a/drivers/iio/gyro/hid-sensor-gyro-3d.c
> > > > > +++ b/drivers/iio/gyro/hid-sensor-gyro-3d.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > enum gyro_3d_channel {
> > > > > @@ -326,18 +324,13 @@ static int hid_gyro_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&gyro_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &gyro_state-
> > > > > > common_attributes);
> > > > > if (ret < 0) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -361,9 +354,7 @@ static int hid_gyro_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&gyro_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &gyro_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -378,8 +369,7 @@ static int hid_gyro_3d_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_GYRO_3D);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&gyro_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &gyro_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/humidity/hid-sensor-humidity.c
> > > > > b/drivers/iio/humidity/hid-sensor-humidity.c
> > > > > index c99b54b0568d..d2318c4aab0f 100644
> > > > > --- a/drivers/iio/humidity/hid-sensor-humidity.c
> > > > > +++ b/drivers/iio/humidity/hid-sensor-humidity.c
> > > > > @@ -7,8 +7,6 @@
> > > > > #include <linux/hid-sensor-hub.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > #include <linux/iio/iio.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > #include <linux/module.h>
> > > > > #include <linux/platform_device.h>
> > > > >
> > > > > @@ -233,12 +231,8 @@ static int hid_humidity_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = devm_iio_triggered_buffer_setup(&pdev->dev,
> > > > > indio_dev,
> > > > > - &iio_pollfunc_store_tim
> > > > > e, NULL,
> > > > > NULL);
> > > > > - if (ret)
> > > > > - return ret;
> > > > > -
> > > > > atomic_set(&humid_st->common_attributes.data_ready, 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &humid_st->common_attributes);
> > > > > if (ret)
> > > > > @@ -261,7 +255,7 @@ static int hid_humidity_probe(struct
> > > > > platform_device *pdev)
> > > > > error_remove_callback:
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_HUMIDITY);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&humid_st-
> > > > > >common_attributes);
> > > > > + hid_sensor_remove_trigger(indio_dev, &humid_st-
> > > > > > common_attributes);
> > > > > return ret;
> > > > > }
> > > > >
> > > > > @@ -274,7 +268,7 @@ static int hid_humidity_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > iio_device_unregister(indio_dev);
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_HUMIDITY);
> > > > > - hid_sensor_remove_trigger(&humid_st-
> > > > > >common_attributes);
> > > > > + hid_sensor_remove_trigger(indio_dev, &humid_st-
> > > > > > common_attributes);
> > > > >
> > > > > return 0;
> > > > > }
> > > > > diff --git a/drivers/iio/light/hid-sensor-als.c
> > > > > b/drivers/iio/light/hid-sensor-als.c
> > > > > index b6cd299517d1..81fa2a422797 100644
> > > > > --- a/drivers/iio/light/hid-sensor-als.c
> > > > > +++ b/drivers/iio/light/hid-sensor-als.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > enum {
> > > > > @@ -308,18 +306,13 @@ static int hid_als_probe(struct
> > > > > platform_device
> > > > > *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&als_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &als_state->common_attributes);
> > > > > if (ret < 0) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -343,9 +336,7 @@ static int hid_als_probe(struct
> > > > > platform_device
> > > > > *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&als_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &als_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -360,8 +351,7 @@ static int hid_als_remove(struct
> > > > > platform_device
> > > > > *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_ALS);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&als_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &als_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/light/hid-sensor-prox.c
> > > > > b/drivers/iio/light/hid-sensor-prox.c
> > > > > index 7e1030af9ba3..e9c04df07344 100644
> > > > > --- a/drivers/iio/light/hid-sensor-prox.c
> > > > > +++ b/drivers/iio/light/hid-sensor-prox.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > #define CHANNEL_SCAN_INDEX_PRESENCE 0
> > > > > @@ -286,18 +284,13 @@ static int hid_prox_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&prox_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &prox_state-
> > > > > >common_attributes);
> > > > > if (ret) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -321,9 +314,7 @@ static int hid_prox_probe(struct
> > > > > platform_device
> > > > > *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&prox_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &prox_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -338,8 +329,7 @@ static int hid_prox_remove(struct
> > > > > platform_device
> > > > > *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_PROX);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&prox_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &prox_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/magnetometer/hid-sensor-magn-3d.c
> > > > > b/drivers/iio/magnetometer/hid-sensor-magn-3d.c
> > > > > index 25e60b233e08..0c09daf87794 100644
> > > > > --- a/drivers/iio/magnetometer/hid-sensor-magn-3d.c
> > > > > +++ b/drivers/iio/magnetometer/hid-sensor-magn-3d.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > enum magn_3d_channel {
> > > > > @@ -519,18 +517,13 @@ static int hid_magn_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - return ret;
> > > > > - }
> > > > > atomic_set(&magn_state-
> > > > > >magn_flux_attributes.data_ready, 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &magn_state-
> > > > > > magn_flux_attributes);
> > > > > if (ret < 0) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + return ret;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -554,9 +547,7 @@ static int hid_magn_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&magn_state-
> > > > > >magn_flux_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &magn_state-
> > > > > > magn_flux_attributes);
> > > > > return ret;
> > > > > }
> > > > >
> > > > > @@ -569,8 +560,7 @@ static int hid_magn_3d_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_COMPASS_3D);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&magn_state-
> > > > > >magn_flux_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &magn_state-
> > > > > > magn_flux_attributes);
> > > > >
> > > > > return 0;
> > > > > }
> > > > > diff --git a/drivers/iio/orientation/hid-sensor-incl-3d.c
> > > > > b/drivers/iio/orientation/hid-sensor-incl-3d.c
> > > > > index 00af68764cda..6aac8bea233a 100644
> > > > > --- a/drivers/iio/orientation/hid-sensor-incl-3d.c
> > > > > +++ b/drivers/iio/orientation/hid-sensor-incl-3d.c
> > > > > @@ -15,8 +15,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > enum incl_3d_channel {
> > > > > @@ -346,18 +344,13 @@ static int hid_incl_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&incl_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &incl_state-
> > > > > > common_attributes);
> > > > > if (ret) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -382,9 +375,7 @@ static int hid_incl_3d_probe(struct
> > > > > platform_device *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&incl_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &incl_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -399,8 +390,7 @@ static int hid_incl_3d_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_INCLINOMETER_3D);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&incl_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &incl_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/orientation/hid-sensor-rotation.c
> > > > > b/drivers/iio/orientation/hid-sensor-rotation.c
> > > > > index 64ae7d04a200..b99f41240e3e 100644
> > > > > --- a/drivers/iio/orientation/hid-sensor-rotation.c
> > > > > +++ b/drivers/iio/orientation/hid-sensor-rotation.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > struct dev_rot_state {
> > > > > @@ -288,18 +286,13 @@ static int hid_dev_rot_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - return ret;
> > > > > - }
> > > > > atomic_set(&rot_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &rot_state-
> > > > > >common_attributes);
> > > > > if (ret) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + return ret;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -323,9 +316,7 @@ static int hid_dev_rot_probe(struct
> > > > > platform_device *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&rot_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &rot_state-
> > > > > > common_attributes);
> > > > > return ret;
> > > > > }
> > > > >
> > > > > @@ -338,8 +329,7 @@ static int hid_dev_rot_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev, hsdev->usage);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&rot_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &rot_state-
> > > > > > common_attributes);
> > > > >
> > > > > return 0;
> > > > > }
> > > > > diff --git a/drivers/iio/pressure/hid-sensor-press.c
> > > > > b/drivers/iio/pressure/hid-sensor-press.c
> > > > > index 953235052155..5e6663f757ae 100644
> > > > > --- a/drivers/iio/pressure/hid-sensor-press.c
> > > > > +++ b/drivers/iio/pressure/hid-sensor-press.c
> > > > > @@ -14,8 +14,6 @@
> > > > > #include <linux/iio/iio.h>
> > > > > #include <linux/iio/sysfs.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > #include "../common/hid-sensors/hid-sensor-trigger.h"
> > > > >
> > > > > #define CHANNEL_SCAN_INDEX_PRESSURE 0
> > > > > @@ -290,18 +288,13 @@ static int hid_press_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = iio_triggered_buffer_setup(indio_dev,
> > > > > &iio_pollfunc_store_time,
> > > > > - NULL, NULL);
> > > > > - if (ret) {
> > > > > - dev_err(&pdev->dev, "failed to initialize
> > > > > trigger
> > > > > buffer\n");
> > > > > - goto error_free_dev_mem;
> > > > > - }
> > > > > atomic_set(&press_state->common_attributes.data_ready,
> > > > > 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &press_state-
> > > > > >common_attributes);
> > > > > if (ret) {
> > > > > dev_err(&pdev->dev, "trigger setup failed\n");
> > > > > - goto error_unreg_buffer_funcs;
> > > > > + goto error_free_dev_mem;
> > > > > }
> > > > >
> > > > > ret = iio_device_register(indio_dev);
> > > > > @@ -325,9 +318,7 @@ static int hid_press_probe(struct
> > > > > platform_device
> > > > > *pdev)
> > > > > error_iio_unreg:
> > > > > iio_device_unregister(indio_dev);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&press_state-
> > > > > >common_attributes);
> > > > > -error_unreg_buffer_funcs:
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &press_state-
> > > > > > common_attributes);
> > > > > error_free_dev_mem:
> > > > > kfree(indio_dev->channels);
> > > > > return ret;
> > > > > @@ -342,8 +333,7 @@ static int hid_press_remove(struct
> > > > > platform_device *pdev)
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_PRESSURE);
> > > > > iio_device_unregister(indio_dev);
> > > > > - hid_sensor_remove_trigger(&press_state-
> > > > > >common_attributes);
> > > > > - iio_triggered_buffer_cleanup(indio_dev);
> > > > > + hid_sensor_remove_trigger(indio_dev, &press_state-
> > > > > > common_attributes);
> > > > > kfree(indio_dev->channels);
> > > > >
> > > > > return 0;
> > > > > diff --git a/drivers/iio/temperature/hid-sensor-temperature.c
> > > > > b/drivers/iio/temperature/hid-sensor-temperature.c
> > > > > index eda55b9c1e9b..8d1f434f109d 100644
> > > > > --- a/drivers/iio/temperature/hid-sensor-temperature.c
> > > > > +++ b/drivers/iio/temperature/hid-sensor-temperature.c
> > > > > @@ -7,8 +7,6 @@
> > > > > #include <linux/hid-sensor-hub.h>
> > > > > #include <linux/iio/buffer.h>
> > > > > #include <linux/iio/iio.h>
> > > > > -#include <linux/iio/triggered_buffer.h>
> > > > > -#include <linux/iio/trigger_consumer.h>
> > > > > #include <linux/module.h>
> > > > > #include <linux/platform_device.h>
> > > > >
> > > > > @@ -230,12 +228,8 @@ static int hid_temperature_probe(struct
> > > > > platform_device *pdev)
> > > > > indio_dev->name = name;
> > > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > >
> > > > > - ret = devm_iio_triggered_buffer_setup(&pdev->dev,
> > > > > indio_dev,
> > > > > - &iio_pollfunc_store_tim
> > > > > e, NULL,
> > > > > NULL);
> > > > > - if (ret)
> > > > > - return ret;
> > > > > -
> > > > > atomic_set(&temp_st->common_attributes.data_ready, 0);
> > > > > +
> > > > > ret = hid_sensor_setup_trigger(indio_dev, name,
> > > > > &temp_st->common_attributes);
> > > > > if (ret)
> > > > > @@ -258,7 +252,7 @@ static int hid_temperature_probe(struct
> > > > > platform_device *pdev)
> > > > > error_remove_callback:
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_TEMPERATURE);
> > > > > error_remove_trigger:
> > > > > - hid_sensor_remove_trigger(&temp_st->common_attributes);
> > > > > + hid_sensor_remove_trigger(indio_dev, &temp_st-
> > > > > > common_attributes);
> > > > > return ret;
> > > > > }
> > > > >
> > > > > @@ -270,7 +264,7 @@ static int hid_temperature_remove(struct
> > > > > platform_device *pdev)
> > > > > struct temperature_state *temp_st =
> > > > > iio_priv(indio_dev);
> > > > >
> > > > > sensor_hub_remove_callback(hsdev,
> > > > > HID_USAGE_SENSOR_TEMPERATURE);
> > > > > - hid_sensor_remove_trigger(&temp_st->common_attributes);
> > > > > + hid_sensor_remove_trigger(indio_dev, &temp_st-
> > > > > > common_attributes);
> > > > >
> > > > > return 0;
> > > > > }
>

\
 
 \ /
  Last update: 2020-04-27 07:39    [W:0.118 / U:0.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site