lkml.org 
[lkml]   [2020]   [Apr]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/6] Documentation: ABI: testing: scd30: document iio attributes
On Wed, Apr 22, 2020 at 06:40:17PM +0200, Peter Meerwald-Stadler wrote:
> On Wed, 22 Apr 2020, Tomasz Duszynski wrote:
>
> > Add documentation for sensor specific iio attributes.
>
> minor comments below

Thanks.

>
> > Signed-off-by: Tomasz Duszynski <tomasz.duszynski@octakon.com>
> > ---
> > Documentation/ABI/testing/sysfs-bus-iio-scd30 | 97 +++++++++++++++++++
> > 1 file changed, 97 insertions(+)
> > create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30
> >
> > diff --git a/Documentation/ABI/testing/sysfs-bus-iio-scd30 b/Documentation/ABI/testing/sysfs-bus-iio-scd30
> > new file mode 100644
> > index 000000000000..0431a718447d
> > --- /dev/null
> > +++ b/Documentation/ABI/testing/sysfs-bus-iio-scd30
> > @@ -0,0 +1,97 @@
> > +What: /sys/bus/iio/devices/iio:deviceX/pressure_comp
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Given that sensor's CO2 measurement chamber has fixed volume
> > + pressure changes will affect concentration readings. Writing
> > + current ambient pressure here will allow senor to make necessary
>
> sensor
>

Okay.

> > + adjustments. Upon reading previously set value is returned.
> > + Units are millibars.
>
> unit for pressure in IIO is kilopascal (e.g.
> /sys/bus/iio/devices/iio:deviceX/in_pressure_raw)
>

My thinking here was that since these are sensor specific attributes
they don't need to stick to iio conventions and millibars were somewhat
more natural to use. But I guess that's just matter of habit.

So generally I am okay with reworking all attrs to accept values in iio
preferred units.

> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/pressure_comp_available
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + The range of available values in millibars represented as the
> > + minimum value, the step and the maximum value, all enclosed in
> > + square brackets.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/meas_interval
> > +Date: January 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Amount of time between subsequent measurements. Writing this
> > + attribute will change measurement interval. Upon reading
> > + current measurement interval is returned. Units are seconds.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/meas_interval_available
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + The range of available values in seconds represented as the
> > + minimum value, the step and the maximum value, all enclosed in
> > + square brackets.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/asc
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Writing 1 or 0 to this attribute will respectively activate or
> > + deactivate automatic self calibration procedure. Upon reading 1
>
> deactivate automatic self calibration (asc) procedure
>

That shouldn't be too difficult to realize what asc actually stands for after
reading this short description.

> > + is returned if asc is ongoing, 0 otherwise.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/frc
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Forced recalibration is used to compensate for sensor drifts
> > + when a reference value of CO2 concentration in close proximity
> > + to the sensor is available. Writing attribute will set frc
> > + value. Upon reading current frc is returned. Units are
> > + millibars.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/frc_available
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + The range of available values in millibars represented as the
> > + minimum value, the step and the maximum value, all enclosed in
> > + square brackets.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/temp_offset
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Sensor readings may be affected by ambient temperature.
> > + Writing temperature offset will compensate for unwanted changes.
> > + Note that written offset gets multiplied by a factor of 100
> > + by a sensor internally.
> > +
> > + For example, writing 10 here will correspond to 0.1 degree
> > + Celsius.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/temp_offset_available
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + The range of available values in degrees Celsius represented as
> > + the minimum value, the step and the maximum value, all enclosed
> > + in square brackets.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/reset
> > +Date: April 2020
> > +KernelVersion: 5.8
> > +Contact: linux-iio@vger.kernel.org
> > +Description:
> > + Software reset mechanism forces sensor into the same state
> > + as after powering up without the need for removing power supply.
> > + Writing any value will reset sensor.
> >
>
> --
>
> Peter Meerwald-Stadler
> Mobile: +43 664 24 44 418

\
 
 \ /
  Last update: 2020-04-23 17:55    [W:0.823 / U:0.724 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site