lkml.org 
[lkml]   [2020]   [Apr]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: More dwc3 gadget issues with adb
Date
John Stultz <john.stultz@linaro.org> writes:

> On Wed, Apr 22, 2020 at 11:32 AM John Stultz <john.stultz@linaro.org> wrote:
>> On Tue, Apr 21, 2020 at 11:00 PM Felipe Balbi <balbi@kernel.org> wrote:
>> > John Stultz <john.stultz@linaro.org> writes:
>> > > that's not an issue as we only have one sg entry. But if its set on a
>> > > trb in a request with multiple sgs, that's where it seems to be
>> > > causing the issue.
>> >
>> > The issue is completing with HWO set, which should never happen. Can you
>> > collect tracepoints with linus/master of this particular situation?
>>
>> Will do, though again, its a little tough as often we hit the stall
>> state pretty quickly at bootup, before I can even try to enable
>> tracing, so it may take a few tries.
>>
>> > >> One interesting thing is that TRB addresses are "odd". I can't find a
>> > >> proper lifetime for these TRBs. Do you have IOMMU enabled? Can you run
>> > >> without it? For example, nowhere in the log can I find the place where
>> > >> trb 0000000092deef41 was first enqueue. I'm assuming the log to be
>> > >> ordered, which means that trb is the same as 00000000f3db4076. But why
>> > >> are the addresses different?
>> > >>
>> > >> Another weird thing is that even though we CHN bit being set in
>> > >> 0000000092deef41, we don't see where the second trb (the one its chained
>> > >> to) was prepared. It seems like it was *never* prepared, what gives?
>> > >
>> > > I suspect these bits were due to the tracing happening after some
>> > > minor amount of initial adb traffic began at bootup? So the trace
>> > > isn't capturing all the events.
>> >
>> > No, no. That's more likely to be IOMMU mucking up the addresses. ADB is
>> > very sequential in its behavior and USB transfers requests in
>> > order. Please run linus/master without IOMMU.
>>
>> So I didn't have any IOMMU support enabled in the config I was testing
>> with. I went through and added IOMMU options in my config with
>> linus/master as well and that didn't seem to change the behavior
>> either.
>>
>> I'll get back to you with further trace logs.
>
> Ok. Attached are trace logs. Two bad cases, which are linus/master w/
> all IOMMU configs disabled.
>
> Then I have a good case where I've removed the
> if (trb->ctrl & DWC3_TRB_CTRL_HWO)
> break;
> logic in dwc3_gadget_ep_reclaim_trb_sg().

Okay, here's the failing case:

UsbFfs-worker-574 [001] d..2 261.788895: dwc3_ep_queue: ep1out: req 000000006efef4fb length 0/16384 zsI ==> -115
UsbFfs-worker-574 [001] d..2 261.788922: dwc3_prepare_trb: ep1out: trb 00000000fa0a991a (E11:D4) buf 00000000ab3d1000 size 4096 ctrl 0000001d (HlCS:sc:normal)
UsbFfs-worker-574 [001] d..2 261.788927: dwc3_prepare_trb: ep1out: trb 000000007f6b91bb (E12:D4) buf 00000000a9534000 size 4096 ctrl 0000001d (HlCS:sc:normal)
UsbFfs-worker-574 [001] d..2 261.788930: dwc3_prepare_trb: ep1out: trb 00000000a64ab194 (E13:D4) buf 00000000d6447000 size 4096 ctrl 0000001d (HlCS:sc:normal)
UsbFfs-worker-574 [001] d..2 261.788934: dwc3_prepare_trb: ep1out: trb 00000000571f893b (E14:D4) buf 00000000d666a000 size 4096 ctrl 00000819 (HlcS:sC:normal)
UsbFfs-worker-574 [001] d..2 261.788962: dwc3_gadget_ep_cmd: ep1out: cmd 'Update Transfer' [20007] params 00000000 00000000 00000000 --> status: Successful
irq/65-dwc3-515 [000] d..1 261.821056: dwc3_event: event (00006084): ep1out: Transfer In Progress [0] (SIm)
irq/65-dwc3-515 [000] d..1 261.821057: dwc3_complete_trb: ep1out: trb 00000000fa0a991a (E22:D11) buf 00000000ab3d1000 size 4072 ctrl 0000001c (hlCS:sc:normal)

So, ffs enqueued a request for 16kiB but only 24 bytes were sent by the
host. This is a short-packet case. It seems like that logic is, indeed,
incorrect. I added it for a reason, though I can't be sure based on the
commit log alone.

I think I was trying to cover the case where we didn't prepare all TRBs
for an SG-list because they didn't fit, but I don't think that's the
right way to achieve what I meant :-p

Could you prepare a patch and Cc stable?

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-04-23 11:49    [W:0.052 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site