lkml.org 
[lkml]   [2020]   [Apr]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] ARM: dts: sun7i: Use syscon-based implementation for gmac
On Mon, Apr 20, 2020 at 02:59:19PM +0200, Maxime Ripard wrote:
> On Sat, Apr 18, 2020 at 01:17:30AM +0300, Priit Laes wrote:
> > Use syscon-based approach to access gmac clock configuration
> > register, instead of relying on a custom clock driver.
> >
> > As a bonus, we can now drop the custom clock implementation
> > and dummy clocks making sun7i fully CCU-compatible.
> >
> > Signed-off-by: Priit Laes <plaes@plaes.org>
> > ---
> > arch/arm/boot/dts/sun7i-a20.dtsi | 36 +++-----------------------------
> > 1 file changed, 3 insertions(+), 33 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
> > index ffe1d10a1a84..750962a94fad 100644
> > --- a/arch/arm/boot/dts/sun7i-a20.dtsi
> > +++ b/arch/arm/boot/dts/sun7i-a20.dtsi
> > @@ -219,37 +219,6 @@ osc32k: clk-32k {
> > clock-frequency = <32768>;
> > clock-output-names = "osc32k";
> > };
> > -
> > - /*
> > - * The following two are dummy clocks, placeholders
> > - * used in the gmac_tx clock. The gmac driver will
> > - * choose one parent depending on the PHY interface
> > - * mode, using clk_set_rate auto-reparenting.
> > - *
> > - * The actual TX clock rate is not controlled by the
> > - * gmac_tx clock.
> > - */
> > - mii_phy_tx_clk: clk-mii-phy-tx {
> > - #clock-cells = <0>;
> > - compatible = "fixed-clock";
> > - clock-frequency = <25000000>;
> > - clock-output-names = "mii_phy_tx";
> > - };
> > -
> > - gmac_int_tx_clk: clk-gmac-int-tx {
> > - #clock-cells = <0>;
> > - compatible = "fixed-clock";
> > - clock-frequency = <125000000>;
> > - clock-output-names = "gmac_int_tx";
> > - };
> > -
> > - gmac_tx_clk: clk@1c20164 {
> > - #clock-cells = <0>;
> > - compatible = "allwinner,sun7i-a20-gmac-clk";
> > - reg = <0x01c20164 0x4>;
> > - clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
> > - clock-output-names = "gmac_tx";
> > - };
> > };
> >
> >
> > @@ -1511,11 +1480,12 @@ mali: gpu@1c40000 {
> >
> > gmac: ethernet@1c50000 {
> > compatible = "allwinner,sun7i-a20-gmac";
> > + syscon = <&ccu>;
> > reg = <0x01c50000 0x10000>;
> > interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> > interrupt-names = "macirq";
> > - clocks = <&ccu CLK_AHB_GMAC>, <&gmac_tx_clk>;
> > - clock-names = "stmmaceth", "allwinner_gmac_tx";
> > + clocks = <&ccu CLK_AHB_GMAC>;
> > + clock-names = "stmmaceth";
>
> I guess you also need to update the binding so that it considers it valid?

Yes, will do it in the next round.

>
> Maxime


\
 
 \ /
  Last update: 2020-04-20 15:24    [W:0.078 / U:0.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site