lkml.org 
[lkml]   [2020]   [Mar]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
Date
Hi Stefan,

On Sun, Mar 29 2020, eichest@gmail.com wrote:
> From: Stefan Eichenberger <eichest@gmail.com>
>
> According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> pin for the gigabit phy is MPP62 and not MPP43.

Have you tested that on real hardware?

The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
deassert delay") indicates that this is the case on his board as well.

In case there was a hardware change between board revisions, we need
another dtb for that revision.

baruch

> Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
> ---
> .../dts/marvell/armada-8040-clearfog-gt-8k.dts | 14 +++++++-------
> 1 file changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> index b90d78a5724b..d371d938b41e 100644
> --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> @@ -144,7 +144,6 @@
> * [35-38] CP0 I2C1 and I2C0
> * [39] GPIO reset button
> * [40,41] LED0 and LED1
> - * [43] 1512 phy reset
> * [47] USB VBUS EN (active low)
> * [48] FAN PWM
> * [49] SFP+ present signal
> @@ -155,6 +154,7 @@
> * [54] NFC reset
> * [55] Micro SD card detect
> * [56-61] Micro SD
> + * [62] 1512 phy reset
> */
>
> cp0_pci0_reset_pins: pci0-reset-pins {
> @@ -197,11 +197,6 @@
> marvell,function = "gpio";
> };
>
> - cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> - marvell,pins = "mpp43";
> - marvell,function = "gpio";
> - };
> -
> cp0_xhci_vbus_pins: xhci0-vbus-pins {
> marvell,pins = "mpp47";
> marvell,function = "gpio";
> @@ -232,6 +227,11 @@
> "mpp60", "mpp61";
> marvell,function = "sdio";
> };
> +
> + cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> + marvell,pins = "mpp62";
> + marvell,function = "gpio";
> + };
> };
>
> &cp0_pcie0 {
> @@ -365,7 +365,7 @@
> reg = <0>;
> pinctrl-names = "default";
> pinctrl-0 = <&cp0_copper_eth_phy_reset>;
> - reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_LOW>;
> reset-assert-us = <10000>;
> reset-deassert-us = <10000>;
> };


--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

\
 
 \ /
  Last update: 2020-03-29 08:31    [W:0.036 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site