lkml.org 
[lkml]   [2020]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC] clk: vc5: Add bindings for output configurations
Hi Adam,

CC Marek

On Thu, Mar 26, 2020 at 10:33 PM Adam Ford <aford173@gmail.com> wrote:
> The Versaclock can be purchased in a non-programmed configuration.
> If that is the case, the driver needs to configure the chip to
> output the correct signal type, voltage and slew.
>
> This RFC is proposing an additional binding to allow non-programmed
> chips to be configured beyond their default configuration.
>
> Signed-off-by: Adam Ford <aford173@gmail.com>
>
> diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> index 05a245c9df08..4bc46ed9ba4a 100644
> --- a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> @@ -30,6 +30,25 @@ Required properties:
> - 5p49v5933 and
> - 5p49v5935: (optional) property not present or "clkin".
>
> +For all output ports, an option child node can be used to specify:
> +
> +- mode: can be one of
> + - LVPECL: Low-voltage positive/psuedo emitter-coupled logic
> + - CMOS
> + - HCSL
> + - LVDS: Low voltage differential signal
> +
> +- voltage-level: can be one of the following microvolts
> + - 1800000
> + - 2500000
> + - 3300000
> +- slew: Percent of normal, can be one of
> + - P80
> + - P85
> + - P90
> + - P100

Why the P prefixes? Can't you just use integer values?
After the conversion to json-schema, these values can be validated, too.

> +
> +
> ==Mapping between clock specifier and physical pins==
>
> When referencing the provided clock in the DT using phandle and
> @@ -62,6 +81,8 @@ clock specifier, the following mapping applies:
>
> ==Example==
>
> +#include <dt-bindings/versaclock.h>

Does not exist?

> +
> /* 25MHz reference crystal */
> ref25: ref25m {
> compatible = "fixed-clock";
> @@ -80,6 +101,13 @@ i2c-master-node {
> /* Connect XIN input to 25MHz reference */
> clocks = <&ref25m>;
> clock-names = "xin";
> +
> + ports@1 {
> + reg = <1>;
> + mode = <CMOS>;
> + pwr_sel = <1800000>;
> + slew = <P80>;
> + };
> };
> };

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2020-03-27 10:42    [W:0.070 / U:0.576 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site