lkml.org 
[lkml]   [2020]   [Mar]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] pinctrl: qcom: use scm_call to route GPIO irq to Apps
On Fri 13 Mar 12:15 PDT 2020, Ansuel Smith wrote:

> For IPQ806x targets, TZ protects the registers that are used to
> configure the routing of interrupts to a target processor.
> To resolve this, this patch uses scm call to route GPIO interrupts
> to application processor. Also the scm call interface is changed.
>

Oh no...but this does look pretty reasonable after all, some comments
and suggestions below.

> Signed-off-by: Ajay Kishore <akisho@codeaurora.org>

With this --author should be Ajay.

> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> ---
> drivers/pinctrl/qcom/pinctrl-msm.c | 36 ++++++++++++++++++++++++++----
> 1 file changed, 32 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
> index 9a8daa256a32..a83cfd1da219 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> @@ -22,6 +22,8 @@
> #include <linux/reboot.h>
> #include <linux/pm.h>
> #include <linux/log2.h>
> +#include <linux/qcom_scm.h>
> +#include <linux/io.h>
>
> #include <linux/soc/qcom/irq.h>
>
> @@ -710,6 +712,9 @@ static void msm_gpio_irq_mask(struct irq_data *d)
> const struct msm_pingroup *g;
> unsigned long flags;
> u32 val;
> + u32 addr;
> + int ret;
> + const __be32 *reg;
>
> if (d->parent_data)
> irq_chip_mask_parent(d);
> @@ -863,6 +868,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
> const struct msm_pingroup *g;
> unsigned long flags;
> u32 val;
> + int ret;
>
> if (d->parent_data)
> irq_chip_set_type_parent(d, type);
> @@ -882,11 +888,33 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
> else
> clear_bit(d->hwirq, pctrl->dual_edge_irqs);
>
> + ret = of_device_is_compatible(pctrl->dev->of_node,
> + "qcom,ipq8064-pinctrl");

This won't change in runtime, so I would like for you to query this
during probe and then carry the result in msm_pinctrl.

> /* Route interrupts to application cpu */
> - val = msm_readl_intr_target(pctrl, g);
> - val &= ~(7 << g->intr_target_bit);
> - val |= g->intr_target_kpss_val << g->intr_target_bit;
> - msm_writel_intr_target(val, pctrl, g);
> + if (!ret) {
> + val = msm_readl_intr_target(pctrl, g);
> + val &= ~(7 << g->intr_target_bit);
> + val |= g->intr_target_kpss_val << g->intr_target_bit;
> + msm_writel_intr_target(val, pctrl, g);
> + } else {
> + const __be32 *reg = of_get_property(pctrl->dev->of_node,
> + "reg", NULL);

This too will be static, and we already resolve this, properly, with
address translation etc during probe.

So if you do a partial rollback of '4b024225c4a8 ("pinctrl: use
devm_platform_ioremap_resource() to simplify code")' you can stash the
base address of the resource in msm_pinctrl, and then make your change
conditional on this being NULL or not.

> +
> + if (reg) {
> + u32 addr = be32_to_cpup(reg) + g->intr_target_reg;
> +
> + qcom_scm_io_readl(addr, &val);
> + __iormb();

Why do you need this and below barriers?

> +
> + val &= ~(7 << g->intr_target_bit);
> + val |= g->intr_target_kpss_val << g->intr_target_bit;
> +
> + __iowmb();
> + ret = qcom_scm_io_writel(addr, val);
> + if (ret)
> + pr_err("\n Routing interrupts to Apps proc failed");

You have msm_pinctrl->dev, so use dev_err(). And the \n goes at the end
in Linux - and perhaps make it include d->hwirq to make it a little bit
informative?

Regards,
Bjorn

> + }
> + }
>
> /* Update configuration for gpio.
> * RAW_STATUS_EN is left on for all gpio irqs. Due to the
> --
> 2.25.0
>

\
 
 \ /
  Last update: 2020-03-26 01:49    [W:0.058 / U:25.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site