[lkml]   [2020]   [Mar]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH 0/7] TI K3 R5F remoteproc support
Hi All,

The following series adds a new K3 R5F remoteproc driver for all the R5F
processor clusters/subsystems on TI AM65x and J721E SoCs. The AM65x has a
single R5FSS cluster, while J721E has three R5FSS clusters. All clusters
are capable of supporting either LockStep (safety compliant providing
fault tolerance) or Split (performance mode) mode. The modes themselves
are limited on some SoC variants through an eFUSE setting. The IP version
and SoC integration is slightly different between AM65x and J721E SoC
families leading to couple of functional behavior differences.

The R5Fs are designed to boot out of TCMs with the initial boot-up code
on the R5Fs configure the Memory Protection Unit (MPU) to run code from
DDR. IPC is through the virtio-rpmsg transport. There is no error recovery
or Power Management support at present. The J721E

The patches are on top of the current rproc-next branch, and uses one
patch from the OMAP remoteproc series [1]. It also leverages the fixed
memory carveout fixes series [2].

The following is the patch summary:
- Patch 1 is an old patch [3] from Loic posted previously to the upstream
lists and allows the driver to perform the necessary sequencing
w.r.t IP power-on and local resets and provide a balanced state
machine across sysfs start/stop, and bind/unbind or module removal.
- Patch 2 is a minor enhancement in remoteproc core to allow dynamically
created platform devices to be registered with remoteproc core.
- Patches 3 and 5 add the base binding and the the driver respectively.
- Patch 4 is a common helper that will also be used by a TI K3 DSP
remoteproc driver (to be posted in the near future) providing the
interface to the System Controller software over TI-SCI for performing
device-specific operations.
- Patches 6 and 7 are couple of incremental features to the R5F driver.



Loic Pallardy (1):
remoteproc: add prepare and unprepare ops

Suman Anna (6):
remoteproc: use a local copy for the name field
dt-bindings: remoteproc: Add bindings for R5F subsystem on TI K3 SoCs
remoteproc/k3-r5: Add TI-SCI processor control helper functions
remoteproc/k3-r5: Add a remoteproc driver for R5F subsystem
remoteproc/k3-r5: Initialize TCM memories for ECC
remoteproc/k3-r5: Add loading support for on-chip SRAM regions

.../bindings/remoteproc/ti,k3-r5f-rproc.yaml | 338 ++++
drivers/remoteproc/Kconfig | 16 +
drivers/remoteproc/Makefile | 1 +
drivers/remoteproc/remoteproc_core.c | 29 +-
drivers/remoteproc/ti_k3_r5_remoteproc.c | 1461 +++++++++++++++++
drivers/remoteproc/ti_sci_proc.h | 102 ++
include/linux/remoteproc.h | 6 +-
7 files changed, 1950 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml
create mode 100644 drivers/remoteproc/ti_k3_r5_remoteproc.c
create mode 100644 drivers/remoteproc/ti_sci_proc.h


 \ /
  Last update: 2020-03-24 21:18    [W:0.309 / U:3.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site