lkml.org 
[lkml]   [2020]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3 1/4] media: dt-bindings: media: i2c: Switch to assigned-clock-rates
Hi Prabhakar,

On Wed, Mar 18, 2020 at 08:13:00PM +0000, Lad, Prabhakar wrote:
> On Fri, Mar 13, 2020 at 9:27 PM Laurent Pinchart wrote:
> > On Fri, Mar 13, 2020 at 09:25:01PM +0000, Prabhakar Mahadev Lad wrote:
> >> On Sent: 13 March 2020 21:20, Laurent Pinchart wrote:
> >>> On Fri, Mar 13, 2020 at 09:12:31PM +0000, Lad Prabhakar wrote:
> >>>> Use assigned-clock-rates to specify the clock rate. Also mark
> >>>> clock-frequency property as deprecated.
> >>>
> >>> I would phrase it the other way around, this patch mainly deprecates clock-
> >>> frequency, and as a side effect recommends usage of assigned-clock-rates.
> >>>
> >>> "Deprecate usage of the clock-frequency propertly. The preferred method
> >>> to set clock rates is to use assigned-clock-rates."
> >>
> >> Agreed will do that.
> >>
> >>>> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >>>> ---
> >>>> Documentation/devicetree/bindings/media/i2c/ov5645.txt | 5 +++--
> >>>> 1 file changed, 3 insertions(+), 2 deletions(-)
> >>>>
> >>>> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> >>>> b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> >>>> index 72ad992..e62fe82 100644
> >>>> --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> >>>> +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> >>>> @@ -8,7 +8,7 @@ Required Properties:
> >>>> - compatible: Value should be "ovti,ov5645".
> >>>> - clocks: Reference to the xclk clock.
> >>>> - clock-names: Should be "xclk".
> >>>> -- clock-frequency: Frequency of the xclk clock.
> >>>> +- clock-frequency (deprecated): Frequency of the xclk clock.
> >>>
> >>> I would drop this completely. Drivers need to ensure backward compatibility,
> >>> but DT bindings should only document the latest version, the history is
> >>> available in git.
> >>
> >> Sure will drop it.
> >>
> >>> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> >>>
> >>> While at it, can I enlist you to convert these bindings to yaml ? :-)
> >>>
> >> Sure will do the honours , will make sure yaml patch is ontop of this patch too.
>
> Shall I enlist you as the maintainer in the json-schema ?
> dt_binding_check says 'maintainers' is a required property.

Do you want to be the new maintainer ? :-) Sakari is maintaining sensor
drivers (in his spare time though) so maybe he could be listed in the DT
bindings too if he wants. Otherwise, I could do it.

> > Thank you :-)
> >
> >>>> - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
> >>>> to the hardware pin PWDNB which is physically active low.
> >>>> - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
> >>>> @@ -37,7 +37,8 @@ Example:
> >>>>
> >>>> clocks = <&clks 200>;
> >>>> clock-names = "xclk";
> >>>> -clock-frequency = <24000000>;
> >>>> +assigned-clocks = <&clks 200>;
> >>>> +assigned-clock-rates = <24000000>;
> >>>>
> >>>> vdddo-supply = <&camera_dovdd_1v8>;
> >>>> vdda-supply = <&camera_avdd_2v8>;

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2020-03-18 23:34    [W:0.079 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site