lkml.org 
[lkml]   [2020]   [Mar]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.19 08/86] serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE
Date
From: Daniel Golle <daniel@makrotopia.org>

[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ]

On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.

Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/tty/serial/ar933x_uart.c | 8 ++++++++
1 file changed, 8 insertions(+)

diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index 3bdd56a1021b2..ea12f10610b64 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -286,6 +286,10 @@ static void ar933x_uart_set_termios(struct uart_port *port,
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
AR933X_UART_CS_HOST_INT_EN);

+ /* enable RX and TX ready overide */
+ ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+ AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
/* reenable the UART */
ar933x_uart_rmw(up, AR933X_UART_CS_REG,
AR933X_UART_CS_IF_MODE_M << AR933X_UART_CS_IF_MODE_S,
@@ -418,6 +422,10 @@ static int ar933x_uart_startup(struct uart_port *port)
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
AR933X_UART_CS_HOST_INT_EN);

+ /* enable RX and TX ready overide */
+ ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+ AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
/* Enable RX interrupts */
up->ier = AR933X_UART_INT_RX_VALID;
ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
--
2.20.1


\
 
 \ /
  Last update: 2020-03-10 14:12    [W:2.822 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site