lkml.org 
[lkml]   [2020]   [Feb]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next v2] net: phy: dp83867: Add speed optimization feature
Date
Set the speed optimization bit on the DP83867 PHY.
This feature can also be strapped on the 64 pin PHY devices
but the 48 pin devices do not have the strap pin available to enable
this feature in the hardware. PHY team suggests to have this bit set.

With this bit set the PHY will auto negotiate and report the link
parameters in the PHYSTS register. This register provides a single
location within the register set for quick access to commonly accessed
information.

In this case when auto negotiation is on the PHY core reads the bits
that have been configured or if auto negotiation is off the PHY core
reads the BMCR register and sets the phydev parameters accordingly.

This Giga bit PHY can throttle the speed to 100Mbps or 10Mbps to accomodate a
4-wire cable. If this should occur the PHYSTS register contains the
current negotiated speed and duplex mode.

In overriding the genphy_read_status the dp83867_read_status will do a
genphy_read_status to setup the LP and pause bits. And then the PHYSTS
register is read and the phydev speed and duplex mode settings are
updated.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
v2 - Updated read status to call genphy_read_status first, added link_change
callback to notify of speed change and use phy_set_bits - https://lore.kernel.org/patchwork/patch/1188348/

drivers/net/phy/dp83867.c | 55 +++++++++++++++++++++++++++++++++++++++
1 file changed, 55 insertions(+)

diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c
index 967f57ed0b65..6f86ca1ebb51 100644
--- a/drivers/net/phy/dp83867.c
+++ b/drivers/net/phy/dp83867.c
@@ -21,6 +21,7 @@
#define DP83867_DEVADDR 0x1f

#define MII_DP83867_PHYCTRL 0x10
+#define MII_DP83867_PHYSTS 0x11
#define MII_DP83867_MICR 0x12
#define MII_DP83867_ISR 0x13
#define DP83867_CFG2 0x14
@@ -118,6 +119,15 @@
#define DP83867_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8)
#define DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT 8

+/* PHY STS bits */
+#define DP83867_PHYSTS_1000 BIT(15)
+#define DP83867_PHYSTS_100 BIT(14)
+#define DP83867_PHYSTS_DUPLEX BIT(13)
+#define DP83867_PHYSTS_LINK BIT(10)
+
+/* CFG2 bits */
+#define DP83867_SPEED_OPTIMIZED_EN (BIT(8) | BIT(9))
+
/* CFG3 bits */
#define DP83867_CFG3_INT_OE BIT(7)
#define DP83867_CFG3_ROBUST_AUTO_MDIX BIT(9)
@@ -287,6 +297,43 @@ static int dp83867_config_intr(struct phy_device *phydev)
return phy_write(phydev, MII_DP83867_MICR, micr_status);
}

+static void dp83867_link_change_notify(struct phy_device *phydev)
+{
+ if (phydev->state != PHY_RUNNING)
+ return;
+
+ if (phydev->speed == SPEED_100 || phydev->speed == SPEED_10)
+ phydev_warn(phydev, "Downshift detected connection is %iMbps\n",
+ phydev->speed);
+}
+
+static int dp83867_read_status(struct phy_device *phydev)
+{
+ int status = phy_read(phydev, MII_DP83867_PHYSTS);
+ int ret;
+
+ ret = genphy_read_status(phydev);
+ if (ret)
+ return ret;
+
+ if (status < 0)
+ return status;
+
+ if (status & DP83867_PHYSTS_DUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (status & DP83867_PHYSTS_1000)
+ phydev->speed = SPEED_1000;
+ else if (status & DP83867_PHYSTS_100)
+ phydev->speed = SPEED_100;
+ else
+ phydev->speed = SPEED_10;
+
+ return 0;
+}
+
static int dp83867_config_port_mirroring(struct phy_device *phydev)
{
struct dp83867_private *dp83867 =
@@ -467,6 +514,11 @@ static int dp83867_config_init(struct phy_device *phydev)
int ret, val, bs;
u16 delay;

+ /* Force speed optimization for the PHY even if it strapped */
+ ret = phy_set_bits(phydev, DP83867_CFG2, DP83867_SPEED_OPTIMIZED_EN);
+ if (ret)
+ return ret;
+
ret = dp83867_verify_rgmii_cfg(phydev);
if (ret)
return ret;
@@ -655,6 +707,9 @@ static struct phy_driver dp83867_driver[] = {
.config_init = dp83867_config_init,
.soft_reset = dp83867_phy_reset,

+ .read_status = dp83867_read_status,
+ .link_change_notify = dp83867_link_change_notify,
+
.get_wol = dp83867_get_wol,
.set_wol = dp83867_set_wol,

--
2.25.0
\
 
 \ /
  Last update: 2020-02-04 19:18    [W:0.164 / U:1.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site