lkml.org 
[lkml]   [2020]   [Feb]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH 2/3] [2/3] mmc: mediatek: command queue support
From
Date
Hi Ulf Hansson:

Thanks for your review in details.
I will update v2 patch based on your suggestion by this week.
By the way, I have replied your question below, please take a look and
provide feedback if any.

Regards,
Chun-Hung Wu

On Mon, 2019-11-11 at 14:37 +0100, Ulf Hansson wrote:
+ Trimmed cc list (please do that as well for your next submission).
>
> On Fri, 1 Nov 2019 at 07:43, Chun-Hung Wu <chun-hung.wu@mediatek.com>
wrote:
> >
> > Support command queue for mt6779 platform.
>
> A lot of changes summarized on only one line. I would appreciate some
> more information here, please.
> -> Will provide more information for v2 driver.

> >
> > Change-Id: I56b866fa4097a3c0bee77f53486c470e4f1944b9
> > Feature:
>
> Drop these please.
>
> > Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
>
> For the next submission, please add the maintainers for the cqhci
> driver. They may have some valuable feedback for you.
> -> ok

> Below follows a few review comments, which are more from a patch
> formatting point of view, than technical.
>
> > ---
> > drivers/mmc/host/mtk-sd.c | 151
+++++++++++++++++++++++++++++++++++++++++++---
> > 1 file changed, 141 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> > index 189e426..b132397 100644
> > --- a/drivers/mmc/host/mtk-sd.c
> > +++ b/drivers/mmc/host/mtk-sd.c
> > @@ -31,6 +31,8 @@
> > #include <linux/mmc/sdio.h>
> > #include <linux/mmc/slot-gpio.h>
> >
> > +#include "cqhci.h"
> > +
> > #define MAX_BD_NUM 1024
> >
>
> /*--------------------------------------------------------------------------*/
> > @@ -151,6 +153,7 @@
> > #define MSDC_INT_DMA_BDCSERR (0x1 << 17) /* W1C */
> > #define MSDC_INT_DMA_GPDCSERR (0x1 << 18) /* W1C */
> > #define MSDC_INT_DMA_PROTECT (0x1 << 19) /* W1C */
> > +#define MSDC_INT_CMDQ (0x1 << 28) /* W1C */
> >
> > /* MSDC_INTEN mask */
> > #define MSDC_INTEN_MMCIRQ (0x1 << 0) /* RW */
> > @@ -181,6 +184,7 @@
> > /* SDC_CFG mask */
> > #define SDC_CFG_SDIOINTWKUP (0x1 << 0) /* RW */
> > #define SDC_CFG_INSWKUP (0x1 << 1) /* RW */
> > +#define SDC_CFG_WRDTOC (0x1fff << 2) /* RW */
> > #define SDC_CFG_BUSWIDTH (0x3 << 16) /* RW */
> > #define SDC_CFG_SDIO (0x1 << 19) /* RW */
> > #define SDC_CFG_SDIOIDE (0x1 << 20) /* RW */
> > @@ -228,6 +232,7 @@
> > #define MSDC_PATCH_BIT_SPCPUSH (0x1 << 29) /* RW */
> > #define MSDC_PATCH_BIT_DECRCTMO (0x1 << 30) /* RW */
> >
> > +#define MSDC_PB1_BUSY_CHECK_SEL (0x1 << 7) /* RW */
> > #define MSDC_PATCH_BIT1_STOP_DLY (0xf << 8) /* RW */
> >
> > #define MSDC_PATCH_BIT2_CFGRESP (0x1 << 15) /* RW */
> > @@ -431,6 +436,7 @@ struct msdc_host {
> > struct msdc_save_para save_para; /* used when gate HCLK */
> > struct msdc_tune_para def_tune_para; /* default tune setting
*/
> > struct msdc_tune_para saved_tune_para; /* tune result of
CMD21/CMD19 */
> > + struct cqhci_host *cq_host;
> > };
> >
> > static const struct mtk_mmc_compatible mt8135_compat = {
> > @@ -527,6 +533,18 @@ struct msdc_host {
> > .use_internal_cd = true,
> > };
> >
> > +static const struct mtk_mmc_compatible mt6779_compat = {
> > + .clk_div_bits = 12,
> > + .hs400_tune = false,
> > + .pad_tune_reg = MSDC_PAD_TUNE0,
> > + .async_fifo = true,
> > + .data_tune = true,
> > + .busy_check = true,
> > + .stop_clk_fix = true,
> > + .enhance_rx = true,
> > + .support_64g = true,
> > +};
> > +
> > static const struct of_device_id msdc_of_ids[] = {
> > { .compatible = "mediatek,mt8135-mmc", .data =
&mt8135_compat},
> > { .compatible = "mediatek,mt8173-mmc", .data =
&mt8173_compat},
> > @@ -536,6 +554,7 @@ struct msdc_host {
> > { .compatible = "mediatek,mt7622-mmc", .data =
&mt7622_compat},
> > { .compatible = "mediatek,mt8516-mmc", .data =
&mt8516_compat},
> > { .compatible = "mediatek,mt7620-mmc", .data =
&mt7620_compat},
> > + { .compatible = "mediatek,mt6779-mmc", .data =
&mt6779_compat},
> > {}
> > };
> > MODULE_DEVICE_TABLE(of, msdc_of_ids);
> > @@ -698,21 +717,21 @@ static void msdc_unprepare_data(struct
msdc_host *host, struct mmc_request *mrq)
> > }
> > }
> >
> > -/* clock control primitives */
> > -static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32
clks)
> > +static u64 msdc_timeout_cal(struct msdc_host *host, u64 ns, u64
clks)
> > {
> > - u32 timeout, clk_ns;
> > + u64 timeout, clk_ns;
> > u32 mode = 0;
> >
> > - host->timeout_ns = ns;
> > - host->timeout_clks = clks;
> > if (host->mmc->actual_clock == 0) {
> > timeout = 0;
> > } else {
> > - clk_ns = 1000000000UL / host->mmc->actual_clock;
> > - timeout = (ns + clk_ns - 1) / clk_ns + clks;
> > + clk_ns = 1000000000ULL;
> > + do_div(clk_ns, host->mmc->actual_clock);
> > + timeout = ns + clk_ns - 1;
> > + do_div(timeout, clk_ns);
> > + timeout += clks;
> > /* in 1048576 sclk cycle unit */
> > - timeout = (timeout + (0x1 << 20) - 1) >> 20;
> > + timeout = DIV_ROUND_UP(timeout, (0x1 << 20));
> > if (host->dev_comp->clk_div_bits == 8)
> > sdr_get_field(host->base + MSDC_CFG,
> > MSDC_CFG_CKMOD, &mode);
> > @@ -722,9 +741,30 @@ static void msdc_set_timeout(struct msdc_host
*host, u32 ns, u32 clks)
> > /*DDR mode will double the clk cycles for data
timeout */
> > timeout = mode >= 2 ? timeout * 2 : timeout;
> > timeout = timeout > 1 ? timeout - 1 : 0;
> > - timeout = timeout > 255 ? 255 : timeout;
> > }
> > - sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC, timeout);
> > + return timeout;
> > +}
> > +
> > +/* clock control primitives */
> > +static void msdc_set_timeout(struct msdc_host *host, u64 ns, u64
clks)
> > +{
> > + u64 timeout;
> > +
> > + host->timeout_ns = ns;
> > + host->timeout_clks = clks;
> > +
> > + timeout = msdc_timeout_cal(host, ns, clks);
> > + sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC,
> > + (u32)(timeout > 255 ? 255 : timeout));
> > +}
>
> Does the above changes make sense to split out in a separate patch?
>
> It looks to me, that these are generic clock updates to the driver
> that really doesn't have to be included in $subject patch.
>
> -> thanks, it's ok to separate the clock things to another patch
> +
> > +static void msdc_set_busy_timeout(struct msdc_host *host, u64 ns,
u64 clks)
> > +{
> > + u64 timeout;
> > +
> > + timeout = msdc_timeout_cal(host, ns, clks);
> > + sdr_set_field(host->base + SDC_CFG, SDC_CFG_WRDTOC,
> > + (u32)(timeout > 8191 ? 8191 : timeout));
> > }
> >
> > static void msdc_gate_clock(struct msdc_host *host)
> > @@ -1413,6 +1453,36 @@ static void msdc_enable_sdio_irq(struct
mmc_host *mmc, int enb)
> > pm_runtime_put_noidle(host->dev);
> > }
> >
> > +#if IS_ENABLED(CONFIG_MMC_CQHCI)
>
> Other drivers Kconfig option, uses "select MMC_CQHCI". Would that make
> this more simple and allowing to remove the "if IS_ENABLED" thingy?
> ->We support both CQHCI and legacy(non-CQHCI). And function
cqhci_irq() ->induce compile error if CONFIG_MMC_CQHCI not defined. We
need this
->option here.

> > +static irqreturn_t msdc_cmdq_irq(struct msdc_host *host, u32
intsts)
> > +{
> > + int cmd_err = 0, dat_err = 0;
> > +
> > + if (intsts & MSDC_INT_RSPCRCERR) {
> > + cmd_err = (unsigned int)-EILSEQ;
> > + dev_err(host->dev, "%s: CMD CRC ERR", __func__);
> > + } else if (intsts & MSDC_INT_CMDTMO) {
> > + cmd_err = (unsigned int)-ETIMEDOUT;
> > + dev_err(host->dev, "%s: CMD TIMEOUT ERR", __func__);
> > + }
> > +
> > + if (intsts & MSDC_INT_DATCRCERR) {
> > + dat_err = (unsigned int)-EILSEQ;
> > + dev_err(host->dev, "%s: DATA CRC ERR", __func__);
> > + } else if (intsts & MSDC_INT_DATTMO) {
> > + dat_err = (unsigned int)-ETIMEDOUT;
> > + dev_err(host->dev, "%s: DATA TIMEOUT ERR",
__func__);
> > + }
> > +
> > + if (cmd_err || dat_err) {
> > + dev_err(host->dev, "cmd_err = %d, dat_err =%d,
intsts = 0x%x",
> > + cmd_err, dat_err, intsts);
> > + }
> > +
> > + return cqhci_irq(host->mmc, 0, cmd_err, dat_err);
> > +}
> > +#endif
> > +
> > static irqreturn_t msdc_irq(int irq, void *dev_id)
> > {
> > struct msdc_host *host = (struct msdc_host *) dev_id;
> > @@ -1449,6 +1519,16 @@ static irqreturn_t msdc_irq(int irq, void
*dev_id)
> > if (!(events & (event_mask & ~MSDC_INT_SDIOIRQ)))
> > break;
> >
> > +#if IS_ENABLED(CONFIG_MMC_CQHCI)
>
> Again, please to avoid these "IS_ENABLED".
> ->We support both CQHCI and legacy(non-CQHCI). And function
cqhci_irq() ->induce compile error if CONFIG_MMC_CQHCI not defined. We
need this
->option here.

> > + if ((host->mmc->caps2 & MMC_CAP2_CQE) &&
> > + (events & MSDC_INT_CMDQ)) {
> > + msdc_cmdq_irq(host, events);
> > + /* clear interrupts */
> > + writel(events, host->base + MSDC_INT);
> > + return IRQ_HANDLED;
> > + }
> > +#endif
> > +
> > if (!mrq) {
> > dev_err(host->dev,
> > "%s: MRQ=NULL; events=%08X;
event_mask=%08X\n",
> > @@ -2132,6 +2212,36 @@ static int msdc_get_cd(struct mmc_host *mmc)
> > return !val;
> > }
> >
> > +static void msdc_cqe_enable(struct mmc_host *mmc)
> > +{
> > + struct msdc_host *host = mmc_priv(mmc);
> > +
> > + /* enable cmdq irq */
> > + writel(MSDC_INT_CMDQ, host->base + MSDC_INTEN);
> > + /* enable busy check */
> > + sdr_set_bits(host->base + MSDC_PATCH_BIT1,
MSDC_PB1_BUSY_CHECK_SEL);
> > + /* default write data / busy timeout 20s */
> > + msdc_set_busy_timeout(host, 20 * 1000000000ULL, 0);
> > + /* default read data timeout 1s */
> > + msdc_set_timeout(host, 1000000000ULL, 0);
>
> Some magic timeout values here. Can you elaborate why these values?
> ->The value is from current msdc specs and calculate a timeout value
>> ->read/write timeout spec

> > +}
> > +
> > +void msdc_cqe_disable(struct mmc_host *mmc, bool recovery)
> > +{
> > + struct msdc_host *host = mmc_priv(mmc);
> > +
> > + /* disable cmdq irq */
> > + sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INT_CMDQ);
> > + /* disable busy check */
> > + sdr_clr_bits(host->base + MSDC_PATCH_BIT1,
MSDC_PB1_BUSY_CHECK_SEL);
> > +
> > + if (recovery) {
> > + sdr_set_field(host->base + MSDC_DMA_CTRL,
> > + MSDC_DMA_CTRL_STOP, 1);
> > + msdc_reset_hw(host);
> > + }
> > +}
> > +
> > static const struct mmc_host_ops mt_msdc_ops = {
> > .post_req = msdc_post_req,
> > .pre_req = msdc_pre_req,
> > @@ -2148,6 +2258,11 @@ static int msdc_get_cd(struct mmc_host *mmc)
> > .hw_reset = msdc_hw_reset,
>
> The hw_reset callback is really for resetting the card, but it seems
> like you are using it to reset the controller. No?
>
> I notice there are some other drivers abusing the callback as well,
> but I am wondering whether it's time to really look into what's going
> on here.
>
> Can you elaborate on why you need this?
> ->We did reset card in msdc_hw_reset() not controller. The bit we set
in ->the function is to reset card.

> > };
> >
> > +static const struct cqhci_host_ops msdc_cmdq_ops = {
> > + .enable = msdc_cqe_enable,
> > + .disable = msdc_cqe_disable,
> > +};
> > +
> > static void msdc_of_property_parse(struct platform_device *pdev,
> > struct msdc_host *host)
> > {
> > @@ -2299,6 +2414,22 @@ static int msdc_drv_probe(struct
platform_device *pdev)
> > host->dma_mask = DMA_BIT_MASK(32);
> > mmc_dev(mmc)->dma_mask = &host->dma_mask;
> >
> > +#if IS_ENABLED(CONFIG_MMC_CQHCI)
> > + if (mmc->caps2 & MMC_CAP2_CQE) {
> > + host->cq_host = devm_kzalloc(host->mmc->parent,
> > + sizeof(*host->cq_host),
> > + GFP_KERNEL);
> > + host->cq_host->caps |= CQHCI_TASK_DESC_SZ_128;
> > + host->cq_host->mmio = host->base + 0x800;
> > + host->cq_host->ops = &msdc_cmdq_ops;
> > + cqhci_init(host->cq_host, mmc, true);
> > + mmc->max_segs = 128;
> > + /* cqhci 16bit length */
> > + /* 0 size, means 65536 so we don't have to -1 here
*/
> > + mmc->max_seg_size = 64 * 1024;
> > + }
> > +#endif
> > +
> > host->timeout_clks = 3 * 1048576;
> > host->dma.gpd = dma_alloc_coherent(&pdev->dev,
> > 2 * sizeof(struct mt_gpdma_desc),
> > --
> > 1.9.1
> >
>
> Kind regards
> Uffe
>
\
 
 \ /
  Last update: 2020-02-04 02:02    [W:0.067 / U:1.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site