lkml.org 
[lkml]   [2020]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 04/11] spi: spi-mem: allow specifying a command's extension
On Wed, 26 Feb 2020 15:06:56 +0530
Pratyush Yadav <p.yadav@ti.com> wrote:

> In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
> the "command extension". There can be 3 types of extensions in xSPI:
> repeat, invert, and hex. When the extension type is "repeat", the same
> opcode is sent twice. When it is "invert", the second byte is the
> inverse of the opcode. When it is "hex" an additional opcode byte based
> is sent with the command whose value can be anything.
>
> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> ---
> drivers/spi/spi-mem.c | 23 +++++++++++++++++++++++
> include/linux/spi/spi-mem.h | 24 ++++++++++++++++++++++++
> 2 files changed, 47 insertions(+)
>
> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> index cb13e0878b95..3838ddc9aeec 100644
> --- a/drivers/spi/spi-mem.c
> +++ b/drivers/spi/spi-mem.c
> @@ -462,6 +462,29 @@ int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
> }
> EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);
>
> +int spi_mem_get_cmd_ext(const struct spi_mem_op *op, u8 *ext)
> +{
> + switch (op->cmd.ext_type) {
> + case SPI_MEM_EXT_INVERT:
> + *ext = ~op->cmd.opcode;
> + break;
> +
> + case SPI_MEM_EXT_REPEAT:
> + *ext = op->cmd.opcode;
> + break;
> +
> + case SPI_MEM_EXT_HEX:
> + *ext = op->cmd.ext;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(spi_mem_get_cmd_ext);
> +
> static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc,
> u64 offs, size_t len, void *buf)
> {
> diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
> index 4669082b4e3b..06ccab17e4d0 100644
> --- a/include/linux/spi/spi-mem.h
> +++ b/include/linux/spi/spi-mem.h
> @@ -67,11 +67,31 @@ enum spi_mem_data_dir {
> SPI_MEM_DATA_OUT,
> };
>
> +/**
> + * enum spi_mem_cmd_ext - describes the command opcode extension in DTR mode
> + * @SPI_MEM_EXT_NONE: no extension. This is the default, and is used in Legacy
> + * SPI mode
> + * @SPI_MEM_EXT_REPEAT: the extension is same as the opcode
> + * @SPI_MEM_EXT_INVERT: the extension is the bitwise inverse of the opcode
> + * @SPI_MEM_EXT_HEX: the extension is any hex value. The command and opcode
> + * combine to form a 16-bit opcode.
> + */
> +enum spi_mem_cmd_ext {
> + SPI_MEM_EXT_NONE = 0,
> + SPI_MEM_EXT_REPEAT,
> + SPI_MEM_EXT_INVERT,
> + SPI_MEM_EXT_HEX,
> +};
> +
> /**
> * struct spi_mem_op - describes a SPI memory operation
> * @cmd.buswidth: number of IO lines used to transmit the command
> * @cmd.opcode: operation opcode
> * @cmd.is_dtr: whether the command opcode should be sent in DTR mode or not
> + * @cmd.ext_type: type of the command opcode extension in DTR mode
> + * @cmd.ext: value of the command opcode extension in DTR mode. It is
> + * only set when 'ext_type' is 'SPI_MEM_EXT_HEX'. In all other
> + * cases, the extension can be directly derived from the opcode.
> * @addr.nbytes: number of address bytes to send. Can be zero if the operation
> * does not need to send an address
> * @addr.buswidth: number of IO lines used to transmit the address cycles
> @@ -97,6 +117,8 @@ struct spi_mem_op {
> u8 buswidth;
> u8 opcode;
> bool is_dtr;
> + enum spi_mem_cmd_ext ext_type;
> + u8 ext;

Could we instead make opcode an u16 (or u8[2]) and pass the number of
bytes, as done for the other addr? Mode can be extracted from the
opcode/nbytes values if really needed, and the caller would be
responsible for filling those fields properly (which shouldn't be too
hard)

> } cmd;
>
> struct {
> @@ -361,6 +383,8 @@ int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
>
> void spi_mem_driver_unregister(struct spi_mem_driver *drv);
>
> +int spi_mem_get_cmd_ext(const struct spi_mem_op *op, u8 *ext);
> +
> #define spi_mem_driver_register(__drv) \
> spi_mem_driver_register_with_owner(__drv, THIS_MODULE)
>

\
 
 \ /
  Last update: 2020-02-27 17:45    [W:0.157 / U:0.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site