lkml.org 
[lkml]   [2020]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 02/11] spi: set mode bits for "spi-rx-dtr" and "spi-tx-dtr"
On Wed, 26 Feb 2020 15:06:54 +0530
Pratyush Yadav <p.yadav@ti.com> wrote:

> These two DT properties express DTR receive and transmit capabilities of
> a SPI flash and controller. Introduce two new mode bits: SPI_RX_DTR and
> SPI_TX_DTR which correspond to the new DT properties. Set these bits
> when the two corresponding properties are present in the device tree.
> Also update the detection of unsupported mode bits to include the new
> bits.
>
> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> ---
> drivers/spi/spi.c | 10 +++++++++-
> include/linux/spi/spi.h | 2 ++
> 2 files changed, 11 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
> index 38b4c78df506..25c8ed9343f9 100644
> --- a/drivers/spi/spi.c
> +++ b/drivers/spi/spi.c
> @@ -1927,6 +1927,13 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
> }
> }
>
> + /* Device DTR mode. */
> + if (of_property_read_bool(nc, "spi-tx-dtr"))
> + spi->mode |= SPI_TX_DTR;
> +
> + if (of_property_read_bool(nc, "spi-rx-dtr"))
> + spi->mode |= SPI_RX_DTR;
> +

If this DTR mode is only used in spi-mem, maybe we shouldn't add those
flags. SPI mem devices are usually smart enough to advertise what they
support, and the subsystem in charge of those devices (in this specific
case, spi-nor) will check what the controller supports
using spi_mem_supports_op(). The only case we might have to deal with
at some point is board level limitations (disabling DTR because the
routing prevents using this mode).

> if (spi_controller_is_slave(ctlr)) {
> if (!of_node_name_eq(nc, "slave")) {
> dev_err(&ctlr->dev, "%pOF is not called 'slave'\n",
> @@ -3252,7 +3259,8 @@ int spi_setup(struct spi_device *spi)
> bad_bits &= ~SPI_CS_HIGH;
> ugly_bits = bad_bits &
> (SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL |
> - SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL);
> + SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL |
> + SPI_TX_DTR | SPI_RX_DTR);
> if (ugly_bits) {
> dev_warn(&spi->dev,
> "setup: ignoring unsupported mode bits %x\n",
> diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
> index 6d16ba01ff5a..bf1108318389 100644
> --- a/include/linux/spi/spi.h
> +++ b/include/linux/spi/spi.h
> @@ -183,6 +183,8 @@ struct spi_device {
> #define SPI_TX_OCTAL 0x2000 /* transmit with 8 wires */
> #define SPI_RX_OCTAL 0x4000 /* receive with 8 wires */
> #define SPI_3WIRE_HIZ 0x8000 /* high impedance turnaround */
> +#define SPI_RX_DTR 0x10000 /* receive in DTR mode */
> +#define SPI_TX_DTR 0x20000 /* transmit in DTR mode */
> int irq;
> void *controller_state;
> void *controller_data;

\
 
 \ /
  Last update: 2020-02-27 17:25    [W:0.187 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site