lkml.org 
[lkml]   [2020]   [Feb]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 10/11] mtd: spi-nor: enable octal DTR mode when possible
Date
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
drivers/mtd/spi-nor/spi-nor.c | 31 +++++++++++++++++++++++++++++++
include/linux/mtd/spi-nor.h | 2 ++
2 files changed, 33 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 06cfc525260c..fdcc1b4abc3f 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -5184,6 +5184,31 @@ static void spi_nor_init_params(struct spi_nor *nor)
spi_nor_late_init_params(nor);
}

+/** spi_nor_octal_dtr_enable() - enable Octal DTR I/O if needed
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_octal_dtr_enable(struct spi_nor *nor)
+{
+ int ret;
+
+ if (!nor->params.octal_dtr_enable)
+ return 0;
+
+ if (!(spi_nor_get_protocol_width(nor->read_proto) == 8 ||
+ spi_nor_get_protocol_width(nor->write_proto) == 8))
+ return 0;
+
+ ret = nor->params.octal_dtr_enable(nor);
+ if (ret)
+ return ret;
+
+ nor->reg_proto = SNOR_PROTO_8_8_8_DTR;
+
+ return 0;
+}
+
/**
* spi_nor_quad_enable() - enable Quad I/O if needed.
* @nor: pointer to a 'struct spi_nor'
@@ -5223,6 +5248,12 @@ static int spi_nor_init(struct spi_nor *nor)
{
int err;

+ err = spi_nor_octal_dtr_enable(nor);
+ if (err) {
+ dev_dbg(nor->dev, "octal mode not supported\n");
+ return err;
+ }
+
err = spi_nor_quad_enable(nor);
if (err) {
dev_dbg(nor->dev, "quad mode not supported\n");
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index f54dbd0f86ab..c653f6713cfc 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -526,6 +526,7 @@ struct spi_nor_locking_ops {
* higher index in the array, the higher priority.
* @erase_map: the erase map parsed from the SFDP Sector Map Parameter
* Table.
+ * @octal_dtr_enable: enables SPI NOR octal DTR mode.
* @quad_enable: enables SPI NOR quad mode.
* @set_4byte: puts the SPI NOR in 4 byte addressing mode.
* @convert_addr: converts an absolute address into something the flash
@@ -549,6 +550,7 @@ struct spi_nor_flash_parameter {

struct spi_nor_erase_map erase_map;

+ int (*octal_dtr_enable)(struct spi_nor *nor);
int (*quad_enable)(struct spi_nor *nor);
int (*set_4byte)(struct spi_nor *nor, bool enable);
u32 (*convert_addr)(struct spi_nor *nor, u32 addr);
--
2.25.0
\
 
 \ /
  Last update: 2020-02-26 10:39    [W:0.106 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site