lkml.org 
[lkml]   [2020]   [Feb]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi supported chips
From
Date
Hi, Jitao:

On Fri, 2020-02-21 at 19:28 +0800, Jitao Shi wrote:
> Add decriptions about supported chips, including MT2701 & MT8173 &
> mt8183
>
> 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> 2. Add property "dpi_pin_mode_swap" and "pinctrl-names" gpio mode dpi mode and
> gpio oupput-low to avoid leakage current.
> 3. Add property "dpi_dual_edge" to config the dpi pin output mode dual edge or
> single edge sample data.
>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
> .../bindings/display/mediatek/mediatek,dpi.txt | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index b6a7e7397b8b..cd6a1469c8b7 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -7,6 +7,7 @@ output bus.
>
> Required properties:
> - compatible: "mediatek,<chip>-dpi"
> + the supported chips are mt2701 , mt8173 and mt8183.
> - reg: Physical base address and length of the controller's registers
> - interrupts: The interrupt signal from the function block.
> - clocks: device clocks
> @@ -16,6 +17,11 @@ Required properties:
> Documentation/devicetree/bindings/graph.txt. This port should be connected
> to the input port of an attached HDMI or LVDS encoder chip.
>
> +Optional properties:
> +- dpi_pin_mode_swap: Swap the pin mode between dpi mode and gpio mode.

When you have both pinctrl-name of "gpiomode" and "dpimode", it imply
that dpi_pin_mode_swap = true, isn't it? If so, I think this property is
redundant.

Regards,
CK

> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +- dpi_dual_edge: Control the RGB 24bit data on 12 pins or 24 pins.
> +
> Example:
>
> dpi0: dpi@1401d000 {
> @@ -26,6 +32,11 @@ dpi0: dpi@1401d000 {
> <&mmsys CLK_MM_DPI_ENGINE>,
> <&apmixedsys CLK_APMIXED_TVDPLL>;
> clock-names = "pixel", "engine", "pll";
> + dpi_dual_edge;
> + dpi_pin_mode_swap;
> + pinctrl-names = "gpiomode", "dpimode";
> + pinctrl-0 = <&dpi_pin_gpio>;
> + pinctrl-1 = <&dpi_pin_func>;
>
> port {
> dpi0_out: endpoint {

\
 
 \ /
  Last update: 2020-02-24 08:51    [W:0.082 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site