lkml.org 
[lkml]   [2020]   [Feb]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/5] clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs
Date
From: Taniya Das <tdas@codeaurora.org>

Add programming sequence support for managing the Lucid PLLs.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 193 +++++++++++++++++++++++++++++++
drivers/clk/qcom/clk-alpha-pll.h | 12 ++
2 files changed, 205 insertions(+)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 0adec585eb4f..9b2dfa08acb2 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -52,6 +52,7 @@
#define PLL_CONFIG_CTL_U1(p) ((p)->offset + (p)->regs[PLL_OFF_CONFIG_CTL_U1])
#define PLL_TEST_CTL(p) ((p)->offset + (p)->regs[PLL_OFF_TEST_CTL])
#define PLL_TEST_CTL_U(p) ((p)->offset + (p)->regs[PLL_OFF_TEST_CTL_U])
+#define PLL_TEST_CTL_U1(p) ((p)->offset + (p)->regs[PLL_OFF_TEST_CTL_U1])
#define PLL_STATUS(p) ((p)->offset + (p)->regs[PLL_OFF_STATUS])
#define PLL_OPMODE(p) ((p)->offset + (p)->regs[PLL_OFF_OPMODE])
#define PLL_FRAC(p) ((p)->offset + (p)->regs[PLL_OFF_FRAC])
@@ -116,6 +117,22 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
[PLL_OFF_ALPHA_VAL] = 0x40,
[PLL_OFF_CAL_VAL] = 0x44,
},
+ [CLK_ALPHA_PLL_TYPE_LUCID] = {
+ [PLL_OFF_L_VAL] = 0x04,
+ [PLL_OFF_CAL_L_VAL] = 0x08,
+ [PLL_OFF_USER_CTL] = 0x0c,
+ [PLL_OFF_USER_CTL_U] = 0x10,
+ [PLL_OFF_USER_CTL_U1] = 0x14,
+ [PLL_OFF_CONFIG_CTL] = 0x18,
+ [PLL_OFF_CONFIG_CTL_U] = 0x1c,
+ [PLL_OFF_CONFIG_CTL_U1] = 0x20,
+ [PLL_OFF_TEST_CTL] = 0x24,
+ [PLL_OFF_TEST_CTL_U] = 0x28,
+ [PLL_OFF_TEST_CTL_U1] = 0x2c,
+ [PLL_OFF_STATUS] = 0x30,
+ [PLL_OFF_OPMODE] = 0x38,
+ [PLL_OFF_ALPHA_VAL] = 0x40,
+ },
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);

@@ -139,6 +156,10 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
#define PLL_OUT_MASK 0x7
#define PLL_RATE_MARGIN 500

+/* LUCID PLL specific settings and offsets */
+#define LUCID_PLL_CAL_VAL 0x44
+#define LUCID_PCAL_DONE BIT(26)
+
#define pll_alpha_width(p) \
((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ? \
ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
@@ -1370,3 +1391,175 @@ const struct clk_ops clk_alpha_pll_postdiv_fabia_ops = {
.set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_fabia_ops);
+
+/**
+ * clk_lucid_pll_configure - configure the lucid pll
+ *
+ * @pll: clk alpha pll
+ * @regmap: register map
+ * @config: configuration to apply for pll
+ */
+void clk_lucid_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+ const struct alpha_pll_config *config)
+{
+ if (config->l)
+ regmap_write(regmap, PLL_L_VAL(pll), config->l);
+
+ regmap_write(regmap, PLL_CAL_L_VAL(pll), LUCID_PLL_CAL_VAL);
+
+ if (config->alpha)
+ regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
+
+ if (config->config_ctl_val)
+ regmap_write(regmap, PLL_CONFIG_CTL(pll),
+ config->config_ctl_val);
+
+ if (config->config_ctl_hi_val)
+ regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
+ config->config_ctl_hi_val);
+
+ if (config->config_ctl_hi1_val)
+ regmap_write(regmap, PLL_CONFIG_CTL_U1(pll),
+ config->config_ctl_hi1_val);
+
+ if (config->user_ctl_val)
+ regmap_write(regmap, PLL_USER_CTL(pll),
+ config->user_ctl_val);
+
+ if (config->user_ctl_hi_val)
+ regmap_write(regmap, PLL_USER_CTL_U(pll),
+ config->user_ctl_hi_val);
+
+ if (config->user_ctl_hi1_val)
+ regmap_write(regmap, PLL_USER_CTL_U1(pll),
+ config->user_ctl_hi1_val);
+
+ if (config->test_ctl_val)
+ regmap_write(regmap, PLL_TEST_CTL(pll),
+ config->test_ctl_val);
+
+ if (config->test_ctl_hi_val)
+ regmap_write(regmap, PLL_TEST_CTL_U(pll),
+ config->test_ctl_hi_val);
+
+ if (config->test_ctl_hi1_val)
+ regmap_write(regmap, PLL_TEST_CTL_U1(pll),
+ config->test_ctl_hi1_val);
+
+ regmap_update_bits(regmap, PLL_MODE(pll), PLL_UPDATE_BYPASS,
+ PLL_UPDATE_BYPASS);
+
+ /* Disable PLL output */
+ regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
+
+ /* Set operation mode to OFF */
+ regmap_write(regmap, PLL_OPMODE(pll), PLL_STANDBY);
+
+ /* Place the PLL in STANDBY mode */
+ regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
+}
+EXPORT_SYMBOL_GPL(clk_lucid_pll_configure);
+
+/*
+ * The Lucid PLL requires a power-on self-calibration which happens when the
+ * PLL comes out of reset. Calibrate in case it is not completed.
+ */
+static int alpha_pll_lucid_prepare(struct clk_hw *hw)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ u32 regval;
+ int ret;
+
+ /* Return early if calibration is not needed. */
+ regmap_read(pll->clkr.regmap, PLL_STATUS(pll), &regval);
+ if (regval & LUCID_PCAL_DONE)
+ return 0;
+
+ /* On/off to calibrate */
+ ret = clk_trion_pll_enable(hw);
+ if (!ret)
+ clk_trion_pll_disable(hw);
+
+ return ret;
+}
+
+static int alpha_pll_lucid_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ unsigned long rrate;
+ u32 regval, l, alpha_width = pll_alpha_width(pll);
+ u64 a;
+ int ret;
+
+ rrate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
+
+ /*
+ * Due to a limited number of bits for fractional rate programming, the
+ * rounded up rate could be marginally higher than the requested rate.
+ */
+ if (rrate > (rate + PLL_RATE_MARGIN) || rrate < rate) {
+ pr_err("Call set rate on the PLL with rounded rates!\n");
+ return -EINVAL;
+ }
+
+ regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
+ regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
+
+ /* Latch the PLL input */
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll),
+ PLL_UPDATE, PLL_UPDATE);
+ if (ret)
+ return ret;
+
+ /* Wait for 2 reference cycles before checking the ACK bit. */
+ udelay(1);
+ regmap_read(pll->clkr.regmap, PLL_MODE(pll), &regval);
+ if (!(regval & ALPHA_PLL_ACK_LATCH)) {
+ pr_err("Lucid PLL latch failed. Output may be unstable!\n");
+ return -EINVAL;
+ }
+
+ /* Return the latch input to 0 */
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll),
+ PLL_UPDATE, 0);
+ if (ret)
+ return ret;
+
+ if (clk_hw_is_enabled(hw)) {
+ ret = wait_for_pll_enable_lock(pll);
+ if (ret)
+ return ret;
+ }
+
+ /* Wait for PLL output to stabilize */
+ udelay(100);
+ return 0;
+}
+
+const struct clk_ops clk_alpha_pll_lucid_ops = {
+ .prepare = alpha_pll_lucid_prepare,
+ .enable = clk_trion_pll_enable,
+ .disable = clk_trion_pll_disable,
+ .is_enabled = clk_trion_pll_is_enabled,
+ .recalc_rate = clk_trion_pll_recalc_rate,
+ .round_rate = clk_alpha_pll_round_rate,
+ .set_rate = alpha_pll_lucid_set_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_lucid_ops);
+
+const struct clk_ops clk_alpha_pll_fixed_lucid_ops = {
+ .enable = clk_trion_pll_enable,
+ .disable = clk_trion_pll_disable,
+ .is_enabled = clk_trion_pll_is_enabled,
+ .recalc_rate = clk_trion_pll_recalc_rate,
+ .round_rate = clk_alpha_pll_round_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_fixed_lucid_ops);
+
+const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
+ .recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
+ .round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
+ .set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_lucid_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index fbc1f67c7a26..704674a153b6 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -14,6 +14,7 @@ enum {
CLK_ALPHA_PLL_TYPE_BRAMMO,
CLK_ALPHA_PLL_TYPE_FABIA,
CLK_ALPHA_PLL_TYPE_TRION,
+ CLK_ALPHA_PLL_TYPE_LUCID,
CLK_ALPHA_PLL_TYPE_MAX,
};

@@ -30,6 +31,7 @@ enum {
PLL_OFF_CONFIG_CTL_U1,
PLL_OFF_TEST_CTL,
PLL_OFF_TEST_CTL_U,
+ PLL_OFF_TEST_CTL_U1,
PLL_OFF_STATUS,
PLL_OFF_OPMODE,
PLL_OFF_FRAC,
@@ -94,10 +96,13 @@ struct alpha_pll_config {
u32 alpha_hi;
u32 config_ctl_val;
u32 config_ctl_hi_val;
+ u32 config_ctl_hi1_val;
u32 user_ctl_val;
u32 user_ctl_hi_val;
+ u32 user_ctl_hi1_val;
u32 test_ctl_val;
u32 test_ctl_hi_val;
+ u32 test_ctl_hi1_val;
u32 main_output_mask;
u32 aux_output_mask;
u32 aux2_output_mask;
@@ -123,10 +128,17 @@ extern const struct clk_ops clk_alpha_pll_fabia_ops;
extern const struct clk_ops clk_alpha_pll_fixed_fabia_ops;
extern const struct clk_ops clk_alpha_pll_postdiv_fabia_ops;

+extern const struct clk_ops clk_alpha_pll_lucid_ops;
+extern const struct clk_ops clk_alpha_pll_fixed_lucid_ops;
+extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
+
void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
+void clk_lucid_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+ const struct alpha_pll_config *config);
+
extern const struct clk_ops clk_trion_fixed_pll_ops;
extern const struct clk_ops clk_trion_pll_postdiv_ops;

--
2.24.1
\
 
 \ /
  Last update: 2020-02-24 05:51    [W:0.166 / U:1.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site