lkml.org 
[lkml]   [2020]   [Feb]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 devicetree 3/6] net: dsa: felix: Use PHY_INTERFACE_MODE_INTERNAL instead of GMII
Date
From: Vladimir Oltean <vladimir.oltean@nxp.com>

phy-mode = "gmii" is confusing because it may mean that the port
supports the 8-bit-wide parallel data interface pinout, which it
doesn't.

It may also be confusing because one of the "gmii" internal ports is
actually overclocked to run at 2.5Gbps (even though, yes, as far as the
switch MAC is concerned, it still thinks it's gigabit).

So use the phy-mode = "internal" property to describe the internal ports
inside the NXP LS1028A chip (the ones facing the ENETC). The change
should be fine, because the device tree bindings document is yet to be
introduced, and there are no stable DT blobs in use.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
---
Changes in v3:
None.

Changes in v2:
Patch is new.

drivers/net/dsa/ocelot/felix.c | 3 +--
drivers/net/dsa/ocelot/felix_vsc9959.c | 3 +--
2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index 3257962c147e..35124ef7e75b 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -176,8 +176,7 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port,
phylink_set(mask, 100baseT_Full);
phylink_set(mask, 1000baseT_Full);

- /* The internal ports that run at 2.5G are overclocked GMII */
- if (state->interface == PHY_INTERFACE_MODE_GMII ||
+ if (state->interface == PHY_INTERFACE_MODE_INTERNAL ||
state->interface == PHY_INTERFACE_MODE_2500BASEX ||
state->interface == PHY_INTERFACE_MODE_USXGMII) {
phylink_set(mask, 2500baseT_Full);
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 2c812b481778..93800e81cdd4 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -955,8 +955,7 @@ static int vsc9959_prevalidate_phy_mode(struct ocelot *ocelot, int port,
phy_interface_t phy_mode)
{
switch (phy_mode) {
- case PHY_INTERFACE_MODE_GMII:
- /* Only supported on internal to-CPU ports */
+ case PHY_INTERFACE_MODE_INTERNAL:
if (port != 4 && port != 5)
return -ENOTSUPP;
return 0;
--
2.17.1
\
 
 \ /
  Last update: 2020-02-23 21:48    [W:0.140 / U:1.780 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site