lkml.org 
[lkml]   [2020]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 3/5] dt-bindings: phy: tegra: Add Tegra194 support
Date
Extend the bindings to cover the set of features found in Tegra194.
Note that, technically, there are four more supplies connected to the
XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
, but the power sequencing requirements of Tegra194 require these to be
under the control of the PMIC.

Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".

Signed-off-by: JC Kuo <jckuo@nvidia.com>
---
Changes in v6: none
Changes in v5:
- re-use "maximum-speed" instead of adding "nvidia,disable-gen2"
Changes in v4: none
Changes in v3: none
Changes in v2:
- fix a typo

.../phy/nvidia,tegra124-xusb-padctl.txt | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
index 9fb682e47c29..7d0089006e67 100644
--- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
+++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
@@ -37,6 +37,7 @@ Required properties:
- Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
- Tegra210: "nvidia,tegra210-xusb-padctl"
- Tegra186: "nvidia,tegra186-xusb-padctl"
+ - Tegra194: "nvidia,tegra194-xusb-padctl"
- reg: Physical base address and length of the controller's registers.
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must include the following entries:
@@ -62,6 +63,10 @@ For Tegra186:
- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.

+For Tegra194:
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+ 3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.

Pad nodes:
==========
@@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
- sata: sata-0
- functions: "usb3-ss", "sata"

+For Tegra194, the list of valid PHY nodes is given below:
+- usb2: usb2-0, usb2-1, usb2-2, usb2-3
+ - functions: "xusb"
+- usb3: usb3-0, usb3-1, usb3-2, usb3-3
+ - functions: "xusb"

Port nodes:
===========
@@ -221,6 +231,11 @@ Optional properties:
is internal. In the absence of this property the port is considered to be
external.

+- maximum-speed: Only for Tegra194. A string property that specifies maximum
+ supported speed of a usb3 port. Valid values are:
+ - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed.
+ - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only.
+
For Tegra124 and Tegra132, the XUSB pad controller exposes the following
ports:
- 3x USB2: usb2-0, usb2-1, usb2-2
@@ -233,6 +248,9 @@ For Tegra210, the XUSB pad controller exposes the following ports:
- 2x HSIC: hsic-0, hsic-1
- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

+For Tegra194, the XUSB pad controller exposes the following ports:
+- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
+- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

Examples:
=========
--
2.17.1
\
 
 \ /
  Last update: 2020-02-12 07:13    [W:0.154 / U:0.688 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site