lkml.org 
[lkml]   [2020]   [Feb]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: TI PCIe xHCI and kexec
On Thu, 6 Feb 2020 at 14:23, Mathias Nyman
<mathias.nyman@linux.intel.com> wrote:
>
> On 6.2.2020 5.37, Joel Stanley wrote:
> > On Wed, 5 Feb 2020 at 09:35, Mathias Nyman
> > <mathias.nyman@linux.intel.com> wrote:
> >>
> >> On 5.2.2020 2.55, Joel Stanley wrote:
> >>> I'm supporting a system that uses Linux-as-a-bootloader to load a
> >>> distro kernel via kexec, The systems have a TI TUSB73x0 PCIe
> >>> controller which goes out to lunch after a kexec. This is the distro
> >>> (post-kexec) kernel:
> >>>
> >>> [ 0.235411] pci 0003:01:00.0: xHCI HW did not halt within 16000
> >>> usec status = 0x0
> >>> [ 1.037298] xhci_hcd 0003:01:00.0: xHCI Host Controller
> >>> [ 1.037367] xhci_hcd 0003:01:00.0: new USB bus registered, assigned
> >>> bus number 1
> >>> [ 1.053481] xhci_hcd 0003:01:00.0: Host halt failed, -110
> >>> [ 1.053523] xhci_hcd 0003:01:00.0: can't setup: -110
> >>> [ 1.053565] xhci_hcd 0003:01:00.0: USB bus 1 deregistered
> >>> [ 1.053629] xhci_hcd 0003:01:00.0: init 0003:01:00.0 fail, -110
> >>> [ 1.053703] xhci_hcd: probe of 0003:01:00.0 failed with error -110
> >>>
>
> >>>
> >>> 0003:01:00.0 USB controller: Texas Instruments TUSB73x0 SuperSpeed USB
> >>> 3.0 xHCI Host Controller (rev 02)
> >>>
> >>> The full debug log of the distro kernel booting is below.
> >>>
> >>> [ 1.037833] xhci_hcd 0003:01:00.0: USBCMD 0x0:
> >>> [ 1.037835] xhci_hcd 0003:01:00.0: HC is being stopped
> >>> [ 1.037837] xhci_hcd 0003:01:00.0: HC has finished hard reset
> >>> [ 1.037839] xhci_hcd 0003:01:00.0: Event Interrupts disabled
> >>> [ 1.037841] xhci_hcd 0003:01:00.0: Host System Error Interrupts disabled
> >>> [ 1.037843] xhci_hcd 0003:01:00.0: HC has finished light reset
> >>> [ 1.037846] xhci_hcd 0003:01:00.0: USBSTS 0x0:
> >>> [ 1.037847] xhci_hcd 0003:01:00.0: Event ring is empty
> >>> [ 1.037849] xhci_hcd 0003:01:00.0: No Host System Error
> >>> [ 1.037851] xhci_hcd 0003:01:00.0: HC is running
> >>
> >> Hmm, all bits in both USBCMD and USBSTS are 0. This is a bit suspicious.
> >> Normally at least USBCMD Run/Stop bit, and USBSTS HCHalted bit have
> >> opposite values.
> >
> > Does this suggest the controller is not responding at all?
> >
>
> The Capability registers looks fine, so does port status registers.
> It's just the operational USBSTS and USBCMD registers that return 0.
>
> Current xhci implementation assumes host failed to halt because USBSTS
> HCHalted bit is still 0, and bails out before reset.
> Host is probably not running, register just returns all zero.
>
> Can you try if the below code works, it checks if host is running from
> an additional place, and continues with the host reset.

Here's the patch applied to 5.6-rc1, and then kexec'd twice (once so
we're running a kernel without any workarounds on shutdown, and the
second time to test the recovery code).

It appears to have made it a bit further:

[ 1.532920] pci 0003:01:00.0: enabling device (0140 -> 0142)
[ 1.549081] pci 0003:01:00.0: xHCI HW did not halt within 16000
usec status = 0x10
[ 1.549119] pci 0003:01:00.0: quirk_usb_early_handoff+0x0/0x7c4
took 15820 usecs

[ 5.494595] xhci_hcd 0003:01:00.0: xHCI Host Controller
[ 5.494670] xhci_hcd 0003:01:00.0: new USB bus registered, assigned
bus number 1
[ 5.510774] xhci_hcd 0003:01:00.0: Host halt failed, -110
[ 5.510791] xhci_hcd 0003:01:00.0: Continue with reset even if host
appears running
[ 5.511271] xhci_hcd 0003:01:00.0: hcc params 0x0270f06d hci
version 0x96 quirks 0x0000000004000000
[ 5.522063] xhci_hcd 0003:01:00.0: xHCI Host Controller
[ 5.522115] xhci_hcd 0003:01:00.0: new USB bus registered, assigned
bus number 2
[ 5.522186] xhci_hcd 0003:01:00.0: Host supports USB 3.0 SuperSpeed

[ 19.003160] xhci_hcd 0003:01:00.0: Abort failed to stop command ring: -110
[ 19.019167] xhci_hcd 0003:01:00.0: Host halt failed, -110
[ 19.019168] xhci_hcd 0003:01:00.0: xHCI host controller not
responding, assume dead
[ 19.019172] xhci_hcd 0003:01:00.0: HC died; cleaning up
[ 19.019299] xhci_hcd 0003:01:00.0: Error while assigning device slot ID
[ 19.019302] xhci_hcd 0003:01:00.0: Max number of devices this xHCI
host supports is 64.


>
> diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> index fe38275363e0..2dbfeaf88574 100644
> --- a/drivers/usb/host/xhci.c
> +++ b/drivers/usb/host/xhci.c
> @@ -177,8 +177,16 @@ int xhci_reset(struct xhci_hcd *xhci)
> }
>
> if ((state & STS_HALT) == 0) {
> - xhci_warn(xhci, "Host controller not halted, aborting reset.\n");
> - return 0;
> + /*
> + * After a kexec TI TUSB73x0 might appear running as its USBSTS
> + * and USBCMD registers return all zeroes. Doublecheck if host
> + * is running from USBCMD RUN bit before bailing out.
> + */
> + command = readl(&xhci->op_regs->command);
> + if (command & CMD_RUN) {
> + xhci_warn(xhci, "Host controller not halted, aborting reset.\n");
> + return 0;
> + }
> }
>
> xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Reset the HC");
> @@ -5217,7 +5225,7 @@ int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks)
> /* Make sure the HC is halted. */
> retval = xhci_halt(xhci);
> if (retval)
> - return retval;
> + xhci_warn(xhci, "Continue with reset even if host appears running\n");
>
> xhci_zero_64b_regs(xhci);

\
 
 \ /
  Last update: 2020-02-10 07:13    [W:1.223 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site