lkml.org 
[lkml]   [2020]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/4] spi: LS7A: Add Loongson LS7A SPI controller driver support
Date
The SPI controller has the following characteristics:

- Full-duplex synchronous serial data transmission
- Support up to 4 variable length byte transmission
- Main mode support
- Mode failure generates an error flag and issues an interrupt request
- Double buffer receiver
- Serial clock with programmable polarity and phase
- SPI can be controlled in wait mode
- Support boot from SPI

Use mtd_debug tool to earse/write/read /dev/mtd0 on development.

eg:

[root@linux mtd-utils-1.0.0]# mtd_debug erase /dev/mtd0 0x20000 0x40000
Erased 262144 bytes from address 0x00020000 in flash
[root@linux mtd-utils-1.0.0]# mtd_debug write /dev/mtd0 0x20000 13 1.img
Copied 13 bytes from 1.img to address 0x00020000 in flash
[root@linux mtd-utils-1.0.0]# mtd_debug read /dev/mtd0 0x20000 13 2.img
Copied 13 bytes from address 0x00020000 in flash to 2.img
[root@linux mtd-utils-1.0.0]# cmp -l 1.img 2.img

Signed-off-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
---

v2:
- keep Kconfig and Makefile sorted
- make the entire comment a C++ one so things look more intentional
- Fix unclear indentation
- make conditional statements to improve legibility
- Don't use static inline
- the core handle message queue
- Add a new binding document
- Fix probe part mixed pdev and PCI
---
drivers/spi/Kconfig | 7 ++
drivers/spi/Makefile | 1 +
drivers/spi/spi-ls7a.c | 324 +++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 332 insertions(+)
create mode 100644 drivers/spi/spi-ls7a.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index aadaea0..af7c0d4 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -413,6 +413,13 @@ config SPI_LP8841_RTC
Say N here unless you plan to run the kernel on an ICP DAS
LP-8x4x industrial computer.

+config SPI_LS7A
+ tristate "Loongson LS7A SPI Controller Support"
+ depends on CPU_LOONGSON64 || COMPILE_TEST
+ help
+ This drivers supports the Loongson LS7A SPI controller in master
+ SPI mode.
+
config SPI_MPC52xx
tristate "Freescale MPC52xx SPI (non-PSC) controller support"
depends on PPC_MPC52xx
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 6fea582..d015cf2 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
+obj-$(CONFIG_SPI_LS7A) += spi-ls7a.o
obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o
diff --git a/drivers/spi/spi-ls7a.c b/drivers/spi/spi-ls7a.c
new file mode 100644
index 0000000..21ca1ab
--- /dev/null
+++ b/drivers/spi/spi-ls7a.c
@@ -0,0 +1,324 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Loongson LS7A SPI Controller driver
+ *
+ * Copyright (C) 2020 Loongson Technology Corporation Limited
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/spi/spi.h>
+#include <linux/pci.h>
+#include <linux/of.h>
+
+/* define spi register */
+#define SPCR 0x00
+#define SPSR 0x01
+#define FIFO 0x02
+#define SPER 0x03
+#define PARA 0x04
+#define SFCS 0x05
+#define TIMI 0x06
+
+struct ls7a_spi {
+ spinlock_t lock;
+ struct spi_master *master;
+ void __iomem *base;
+ int cs_active;
+ unsigned int hz;
+ unsigned char spcr, sper;
+ unsigned int mode;
+};
+
+static void ls7a_spi_write_reg(struct ls7a_spi *spi,
+ unsigned char reg,
+ unsigned char data)
+{
+ writeb(data, spi->base + reg);
+}
+
+static char ls7a_spi_read_reg(struct ls7a_spi *spi,
+ unsigned char reg)
+{
+ return readb(spi->base + reg);
+}
+
+static int set_cs(struct ls7a_spi *ls7a_spi, struct spi_device *spi, int val)
+{
+ int cs = ls7a_spi_read_reg(ls7a_spi, SFCS) & ~(0x11 << spi->chip_select);
+
+ if (spi->mode & SPI_CS_HIGH)
+ val = !val;
+ ls7a_spi_write_reg(ls7a_spi, SFCS,
+ (val ? (0x11 << spi->chip_select):(0x1 << spi->chip_select)) | cs);
+
+ return 0;
+}
+
+static int ls7a_spi_do_transfer(struct ls7a_spi *ls7a_spi,
+ struct spi_device *spi,
+ struct spi_transfer *t)
+{
+ unsigned int hz;
+ unsigned int div, div_tmp;
+ unsigned int bit;
+ unsigned long clk;
+ unsigned char val;
+ const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
+
+ if (t) {
+ hz = t->speed_hz;
+ if (!hz)
+ hz = spi->max_speed_hz;
+ } else
+ hz = spi->max_speed_hz;
+
+ if (((spi->mode ^ ls7a_spi->mode) & (SPI_CPOL | SPI_CPHA))
+ || (hz && ls7a_spi->hz != hz)) {
+ clk = 100000000;
+
+ div = DIV_ROUND_UP(clk, hz);
+ if (div < 2)
+ div = 2;
+ if (div > 4096)
+ div = 4096;
+
+ bit = fls(div) - 1;
+ if ((1<<bit) == div)
+ bit--;
+ div_tmp = rdiv[bit];
+
+ dev_dbg(&spi->dev, "clk = %ld hz = %d div_tmp = %d bit = %d\n",
+ clk, hz, div_tmp, bit);
+
+ ls7a_spi->hz = hz;
+ ls7a_spi->spcr = div_tmp & 3;
+ ls7a_spi->sper = (div_tmp >> 2) & 3;
+
+ val = ls7a_spi_read_reg(ls7a_spi, SPCR);
+ val &= ~0xc;
+ if (spi->mode & SPI_CPOL)
+ val |= 8;
+ if (spi->mode & SPI_CPHA)
+ val |= 4;
+ ls7a_spi_write_reg(ls7a_spi, SPCR, (val & ~3) | ls7a_spi->spcr);
+ val = ls7a_spi_read_reg(ls7a_spi, SPER);
+ ls7a_spi_write_reg(ls7a_spi, SPER, (val & ~3) | ls7a_spi->sper);
+ ls7a_spi->mode = spi->mode;
+ }
+ return 0;
+}
+
+static int ls7a_spi_setup(struct spi_device *spi)
+{
+ struct ls7a_spi *ls7a_spi;
+
+ ls7a_spi = spi_master_get_devdata(spi->master);
+
+ if (spi->chip_select >= spi->master->num_chipselect)
+ return -EINVAL;
+
+ set_cs(ls7a_spi, spi, 1);
+
+ return 0;
+}
+
+static int ls7a_spi_write_read_8bit(struct spi_device *spi,
+ const u8 **tx_buf, u8 **rx_buf,
+ unsigned int num)
+{
+ struct ls7a_spi *ls7a_spi;
+
+ ls7a_spi = spi_master_get_devdata(spi->master);
+
+ if (tx_buf && *tx_buf) {
+ ls7a_spi_write_reg(ls7a_spi, FIFO, *((*tx_buf)++));
+
+ while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x1) == 1)
+ ;
+ } else {
+ ls7a_spi_write_reg(ls7a_spi, FIFO, 0);
+
+ while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x1) == 1)
+ ;
+ }
+
+ if (rx_buf && *rx_buf)
+ *(*rx_buf)++ = ls7a_spi_read_reg(ls7a_spi, FIFO);
+ else
+ ls7a_spi_read_reg(ls7a_spi, FIFO);
+
+ return 1;
+}
+
+static unsigned int ls7a_spi_write_read(struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ struct ls7a_spi *ls7a_spi;
+ unsigned int count;
+ const u8 *tx = xfer->tx_buf;
+ u8 *rx = xfer->rx_buf;
+
+ ls7a_spi = spi_master_get_devdata(spi->master);
+ count = xfer->len;
+
+ do {
+ if (ls7a_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
+ goto out;
+ count--;
+ } while (count);
+
+out:
+ return xfer->len - count;
+}
+
+static int ls7a_spi_transfer_one_message(struct spi_master *master,
+ struct spi_message *m)
+{
+ struct ls7a_spi *ls7a_spi;
+ struct spi_device *spi;
+ struct spi_transfer *t = NULL;
+ int param, status, r;
+ unsigned int total_len = 0;
+ unsigned int cs_change;
+ const int nsecs = 50;
+
+ ls7a_spi = spi_master_get_devdata(master);
+ spi = m->spi;
+
+ cs_change = 1;
+
+ spin_lock(&ls7a_spi->lock);
+ param = ls7a_spi_read_reg(ls7a_spi, PARA);
+ ls7a_spi_write_reg(ls7a_spi, PARA, param&~1);
+ spin_unlock(&ls7a_spi->lock);
+ list_for_each_entry(t, &m->transfers, transfer_list) {
+ if (cs_change) {
+ set_cs(ls7a_spi, spi, 0);
+ ls7a_spi_do_transfer(ls7a_spi, spi, t);
+ ndelay(nsecs);
+ }
+ cs_change = t->cs_change;
+
+ r = ls7a_spi_write_read(spi, t);
+ if (r < 0) {
+ status = r;
+ goto error;
+ }
+ total_len += r;
+
+ spi_transfer_delay_exec(t);
+
+ if (cs_change) {
+ set_cs(ls7a_spi, spi, 1);
+ ndelay(nsecs);
+ }
+ }
+
+ spin_lock(&ls7a_spi->lock);
+ ls7a_spi_write_reg(ls7a_spi, PARA, param);
+ spin_unlock(&ls7a_spi->lock);
+
+ if (!cs_change) {
+ ndelay(nsecs);
+ set_cs(ls7a_spi, spi, 1);
+ }
+
+error:
+ m->status = status;
+ m->actual_length = total_len;
+ spi_finalize_current_message(master);
+ return status;
+}
+
+static int ls7a_spi_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct device *dev = &pdev->dev;
+ struct spi_master *master;
+ struct ls7a_spi *spi;
+ int ret;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct ls7a_spi));
+ if (!master)
+ return -ENOMEM;
+
+ spi = spi_master_get_devdata(master);
+ ret = pcim_enable_device(pdev);
+ if (ret)
+ goto err_free_master;
+
+ ret = pci_request_regions(pdev, "ls7a-spi");
+ if (ret)
+ goto err_free_master;
+
+ spi->base = pcim_iomap(pdev, 0, pci_resource_len(pdev, 0));
+ if (!spi->base) {
+ ret = -EINVAL;
+ goto err_free_master;
+ }
+ ls7a_spi_write_reg(spi, SPCR, 0x51);
+ ls7a_spi_write_reg(spi, SPER, 0x00);
+ ls7a_spi_write_reg(spi, TIMI, 0x01);
+ ls7a_spi_write_reg(spi, PARA, 0x40);
+ spi->mode = 0;
+
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+ master->setup = ls7a_spi_setup;
+ master->transfer_one_message = ls7a_spi_transfer_one_message;
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->num_chipselect = 4;
+ master->dev.of_node = of_node_get(pdev->dev.of_node);
+
+ spi->master = master;
+
+ pci_set_drvdata(pdev, master);
+
+ ret = devm_spi_register_master(dev, master);
+ if (ret)
+ goto err_free_master;
+
+ return 0;
+
+err_free_master:
+ pci_release_regions(pdev);
+ spi_master_put(master);
+ return ret;
+}
+
+static void ls7a_spi_pci_remove(struct pci_dev *pdev)
+{
+ struct spi_master *master = pci_get_drvdata(pdev);
+ struct ls7a_spi *spi;
+
+ spi = spi_master_get_devdata(master);
+ if (!spi)
+ return;
+
+ pci_release_regions(pdev);
+}
+
+static const struct pci_device_id ls7a_spi_pci_id_table[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
+ { 0, }
+};
+
+MODULE_DEVICE_TABLE(pci, ls7a_spi_pci_id_table);
+
+static struct pci_driver ls7a_spi_pci_driver = {
+ .name = "ls7a-spi",
+ .id_table = ls7a_spi_pci_id_table,
+ .probe = ls7a_spi_pci_probe,
+ .remove = ls7a_spi_pci_remove,
+};
+
+module_pci_driver(ls7a_spi_pci_driver);
+
+MODULE_AUTHOR("Juxin Gao <gaojuxin@loongson.cn>");
+MODULE_AUTHOR("Qing Zhang <zhangqing@loongson.cn>");
+MODULE_DESCRIPTION("Loongson LS7A SPI controller driver");
--
2.1.0
\
 
 \ /
  Last update: 2020-12-08 08:47    [W:0.087 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site