lkml.org 
[lkml]   [2020]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: Kernel 5.10-rc1 not mounting NAND flash (Bisected to d7157ff49a5b ("mtd: rawnand: Use the ECC framework user input parsing bits"))

Quoting Miquel Raynal <miquel.raynal@bootlin.com>:

> Hi Christophe,
>
> Christophe Leroy <christophe.leroy@csgroup.eu> wrote on Wed, 4 Nov 2020
> 19:37:57 +0100:
>
>> Hi Miquel,
>>
>> Le 04/11/2020 à 18:38, Miquel Raynal a écrit :
>> > Hi Christophe,
>> >
>> > Christophe Leroy <christophe.leroy@csgroup.eu> wrote on Wed, 04 Nov
>> > 2020 18:33:53 +0100:
>> >
>> >> Hi Miquel,
>> >>
>> >> I'm unable to boot 5.10-rc1 on my boards. I get the following error:
>> >>
>> >> [ 4.125811] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x76
>> >> [ 4.131992] nand: Hynix NAND 64MiB 3,3V 8-bit
>> >> [ 4.136173] nand: 64 MiB, SLC, erase size: 16 KiB, page size:
>> 512, OOB size: 16
>> >> [ 4.143534] ------------[ cut here ]------------
>> >> [ 4.147934] Unsupported ECC algorithm!
>> >> [ 4.152142] WARNING: CPU: 0 PID: 1 at
>> drivers/mtd/nand/raw/nand_base.c:5244
>> nand_scan_with_ids+0x1260/0x1640
>> >> ...
>> >> [ 4.332052] ---[ end trace e3a36f62cae4ac56 ]---
>> >> [ 4.336882] gpio-nand: probe of c0000000.nand failed with error -22
>> >>
>> >> Bisected to commit d7157ff49a5b ("mtd: rawnand: Use the ECC
>> framework user input parsing bits")
>> >>
>> >> My first impression is that with that change, the value set in
>> chip->ecc.algo
>> >> by gpio_nand_probe() in drivers/mtd/nand/raw/gpio.c gets
>> overwritten in rawnand_dt_init()
>> >>
>> >> The following change fixes the problem, though I'm not sure it
>> is the right fix. Can you have a look ?
>> >>
>> >> diff --git a/drivers/mtd/nand/raw/nand_base.c
>> b/drivers/mtd/nand/raw/nand_base.c
>> >> index 1f0d542d5923..aa74797cf2da 100644
>> >> --- a/drivers/mtd/nand/raw/nand_base.c
>> >> +++ b/drivers/mtd/nand/raw/nand_base.c
>> >> @@ -5032,7 +5032,8 @@ static int rawnand_dt_init(struct nand_chip *chip)
>> >> chip->ecc.engine_type = nand->ecc.defaults.engine_type;
>> >>
>> >> chip->ecc.placement = nand->ecc.user_conf.placement;
>> >> - chip->ecc.algo = nand->ecc.user_conf.algo;
>> >> + if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
>> >> + chip->ecc.algo = nand->ecc.user_conf.algo;
>> >> chip->ecc.strength = nand->ecc.user_conf.strength;
>> >> chip->ecc.size = nand->ecc.user_conf.step_size;
>> >>
>> >> ---
>> >>
>> >> Thanks
>> >> Christophe
>> >
>> > Sorry for introducing this issue, I didn't had the time to send the
>> > Fixes PR yet but I think this issue has been solved already. Could
>> > you please try with a recent linux-next?
>> >
>>
>> Sorry, same problem with "Linux version 5.10.0-rc2-next-20201104"
>
> Can you please give this patch a try, please?
>
> ---8<---
>
> Author: Miquel Raynal <miquel.raynal@bootlin.com>
> Date: Thu Nov 5 08:44:48 2020 +0100
>
> mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()
>
> While forcing a Hamming software ECC looks clearly wrong, let's just
> fix the situation for now and move these lines to the ->attach_chip()
> hook which gets executed after the user input parsing and NAND chip
> discovery.
>
> Fixes: d7157ff49a5b ("mtd: rawnand: Use the ECC framework user
> input parsing bits")
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
>
> diff --git a/drivers/mtd/nand/raw/gpio.c b/drivers/mtd/nand/raw/gpio.c
> index 3bd847ccc3f3..6feab847f5e0 100644
> --- a/drivers/mtd/nand/raw/gpio.c
> +++ b/drivers/mtd/nand/raw/gpio.c
> @@ -161,8 +161,15 @@ static int gpio_nand_exec_op(struct nand_chip *chip,
> return ret;
> }
>
> +static int gpio_nand_attach_chip(struct nand_chip *chip)
> +{
> + chip->ecc.mode = NAND_ECC_SOFT;
> + chip->ecc.algo = NAND_ECC_HAMMING;
> +}
> +
> static const struct nand_controller_ops gpio_nand_ops = {
> .exec_op = gpio_nand_exec_op,
> + .attach_chip = gpio_nand_attach_chip,
> };
>
> #ifdef CONFIG_OF
> @@ -342,8 +349,6 @@ static int gpio_nand_probe(struct platform_device *pdev)
> gpiomtd->base.ops = &gpio_nand_ops;
>
> nand_set_flash_node(chip, pdev->dev.of_node);
> - chip->ecc.mode = NAND_ECC_SOFT;
> - chip->ecc.algo = NAND_ECC_HAMMING;
> chip->options = gpiomtd->plat.options;
> chip->controller = &gpiomtd->base;


Works with the following:

diff --git a/drivers/mtd/nand/raw/gpio.c b/drivers/mtd/nand/raw/gpio.c
index 4ec0a1e10867..66d3f1eb788c 100644
--- a/drivers/mtd/nand/raw/gpio.c
+++ b/drivers/mtd/nand/raw/gpio.c
@@ -161,8 +161,17 @@ static int gpio_nand_exec_op(struct nand_chip *chip,
return ret;
}

+static int gpio_nand_attach_chip(struct nand_chip *chip)
+{
+ chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+ chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
+
+ return 0;
+}
+
static const struct nand_controller_ops gpio_nand_ops = {
.exec_op = gpio_nand_exec_op,
+ .attach_chip = gpio_nand_attach_chip,
};

#ifdef CONFIG_OF
@@ -342,8 +351,6 @@ static int gpio_nand_probe(struct platform_device *pdev)
gpiomtd->base.ops = &gpio_nand_ops;

nand_set_flash_node(chip, pdev->dev.of_node);
- chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
- chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
chip->options = gpiomtd->plat.options;
chip->controller = &gpiomtd->base;

---
Christophe
\
 
 \ /
  Last update: 2020-11-05 10:05    [W:0.078 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site