lkml.org 
[lkml]   [2020]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] mfd: fix spelling mistakes
Date
Signed-off-by: Michael Klein <michael@fossekall.de>
---
drivers/regulator/da9055-regulator.c | 4 ++--
include/linux/mfd/da9055/reg.h | 4 ++--
include/linux/mfd/si476x-core.h | 2 +-
3 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c
index 73ff5fc7d8d7..c0394ac5e60a 100644
--- a/drivers/regulator/da9055-regulator.c
+++ b/drivers/regulator/da9055-regulator.c
@@ -184,7 +184,7 @@ static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev)
ret &= info->conf.sel_mask;

/* Get the voltage for the active register set A/B */
- if (ret == DA9055_REGUALTOR_SET_A)
+ if (ret == DA9055_REGULATOR_SET_A)
ret = da9055_reg_read(regulator->da9055, volt.reg_a);
else
ret = da9055_reg_read(regulator->da9055, volt.reg_b);
@@ -231,7 +231,7 @@ static int da9055_regulator_set_voltage_sel(struct regulator_dev *rdev,
ret &= info->conf.sel_mask;

/* Set the voltage */
- if (ret == DA9055_REGUALTOR_SET_A)
+ if (ret == DA9055_REGULATOR_SET_A)
return da9055_reg_update(regulator->da9055, info->volt.reg_a,
info->volt.v_mask, selector);
else
diff --git a/include/linux/mfd/da9055/reg.h b/include/linux/mfd/da9055/reg.h
index 54a717b6c3de..1204e6b152d5 100644
--- a/include/linux/mfd/da9055/reg.h
+++ b/include/linux/mfd/da9055/reg.h
@@ -344,8 +344,8 @@
#define DA9055_VLDO_GPI_MASK 0x60
#define DA9055_LDO_CONF_SHIFT 0x07
#define DA9055_LDO_CONF_MASK 0x80
-#define DA9055_REGUALTOR_SET_A 0x00
-#define DA9055_REGUALTOR_SET_B 0x10
+#define DA9055_REGULATOR_SET_A 0x00
+#define DA9055_REGULATOR_SET_B 0x10

/* DA9055_REG_ADC_MAN (addr=0x1B) */
#define DA9055_ADC_MUX_SHIFT 0
diff --git a/include/linux/mfd/si476x-core.h b/include/linux/mfd/si476x-core.h
index 4708c2b8512a..dd95c37ca134 100644
--- a/include/linux/mfd/si476x-core.h
+++ b/include/linux/mfd/si476x-core.h
@@ -57,7 +57,7 @@ enum si476x_mfd_cells {
* @SI476X_POWER_DOWN: In this state all regulators are turned off
* and the reset line is pulled low. The device is completely
* inactive.
- * @SI476X_POWER_UP_FULL: In this state all the power regualtors are
+ * @SI476X_POWER_UP_FULL: In this state all the power regulators are
* turned on, reset line pulled high, IRQ line is enabled(polling is
* active for polling use scenario) and device is turned on with
* POWER_UP command. The device is ready to be used.
--
2.29.2
\
 
 \ /
  Last update: 2020-11-24 19:40    [W:2.070 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site