lkml.org 
[lkml]   [2020]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/3] hwmon: ltc2992: Add support
On Wed, Nov 11, 2020 at 06:20:55PM +0200, alexandru.tachici@analog.com wrote:
> From: Alexandru Tachici <alexandru.tachici@analog.com>
>
> LTC2992 is a rail-to-rail system monitor that
> measures current, voltage, and power of two supplies.
>
> Two ADCs simultaneously measure each supply’s current.
> A third ADC monitors the input voltages and four
> auxiliary external voltages.
>
> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/ltc2992.rst | 56 +++
> drivers/hwmon/Kconfig | 11 +
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/ltc2992.c | 818 ++++++++++++++++++++++++++++++++
> 5 files changed, 887 insertions(+)
> create mode 100644 Documentation/hwmon/ltc2992.rst
> create mode 100644 drivers/hwmon/ltc2992.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index e6b91ab12978..98575a8b1918 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -100,6 +100,7 @@ Hardware Monitoring Kernel Drivers
> lm95234
> lm95245
> lochnagar
> + ltc2992
> ltc2945
> ltc2947
> ltc2978
> diff --git a/Documentation/hwmon/ltc2992.rst b/Documentation/hwmon/ltc2992.rst
> new file mode 100644
> index 000000000000..46aa1aa84a1a
> --- /dev/null
> +++ b/Documentation/hwmon/ltc2992.rst
> @@ -0,0 +1,56 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver ltc2992
> +=====================
> +
> +Supported chips:
> + * Linear Technology LTC2992
> + Prefix: 'ltc2992'
> + Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ltc2992.pdf
> +
> +Author: Alexandru Tachici <alexandru.tachici@analog.com>
> +
> +
> +Description
> +-----------
> +
> +This driver supports hardware monitoring for Linear Technology LTC2992 power monitor.
> +
> +LTC2992 is a rail-to-rail system monitor that measures current,
> +voltage, and power of two supplies.
> +
> +Two ADCs simultaneously measure each supply’s current. A third ADC monitors
> +the input voltages and four auxiliary external voltages.
> +
> +
> +Sysfs entries
> +-------------
> +
> +The following attributes are supported. Limits are read-write,
> +all other attributes are read-only.
> +
> +in_reset_history Reset all highest/lowest values.
> +
> +inX_input Measured voltage.
> +inX_lowest Minimum measured voltage.
> +inX_highest Maximum measured voltage.
> +inX_min Minimum voltage allowed.
> +inX_max Maximum voltage allowed.
> +inX_min_alarm An undervoltage occurred. Cleared on read.
> +inX_max_alarm An overvoltage occurred. Cleared on read.
> +
> +currX_input Measured current.
> +currX_lowest Minimum measured current.
> +currX_highest Maximum measured current.
> +currX_min Minimum current allowed.
> +currX_max Maximum current allowed.
> +currX_min_alarm An undercurrent occurred. Cleared on read.
> +currX_max_alarm An overcurrent occurred. Cleared on read.
> +
> +powerX_input Measured power.
> +powerX_input_lowest Minimum measured voltage.
> +powerX_input_highest Maximum measured voltage.
> +powerX_min Minimum power.
> +powerX_max Maximum power.
> +powerX_min_alarm An underpower occurred. Cleared on read.
> +powerX_max_alarm An overpower occurred. Cleared on read.
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index a850e4f0e0bd..bf9e387270d6 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -858,6 +858,17 @@ config SENSORS_LTC2990
> This driver can also be built as a module. If so, the module will
> be called ltc2990.
>
> +config SENSORS_LTC2992
> + tristate "Linear Technology LTC2992"
> + depends on I2C
> + help
> + If you say yes here you get support for Linear Technology LTC2992
> + I2C System Monitor. The LTC2992 measures current, voltage, and
> + power of two supplies.
> +
> + This driver can also be built as a module. If so, the module will
> + be called ltc2992.
> +
> config SENSORS_LTC4151
> tristate "Linear Technology LTC4151"
> depends on I2C
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 9db2903b61e5..d6172c4807c4 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -118,6 +118,7 @@ obj-$(CONFIG_SENSORS_LTC2947) += ltc2947-core.o
> obj-$(CONFIG_SENSORS_LTC2947_I2C) += ltc2947-i2c.o
> obj-$(CONFIG_SENSORS_LTC2947_SPI) += ltc2947-spi.o
> obj-$(CONFIG_SENSORS_LTC2990) += ltc2990.o
> +obj-$(CONFIG_SENSORS_LTC2992) += ltc2992.o
> obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o
> obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o
> obj-$(CONFIG_SENSORS_LTC4222) += ltc4222.o
> diff --git a/drivers/hwmon/ltc2992.c b/drivers/hwmon/ltc2992.c
> new file mode 100644
> index 000000000000..ce679405ac81
> --- /dev/null
> +++ b/drivers/hwmon/ltc2992.c
> @@ -0,0 +1,818 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * LTC2992 - Dual Wide Range Power Monitor
> + *
> + * Copyright 2020 Analog Devices Inc.
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/bits.h>

You only use BIT(), so a single include should be sufficient.

> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>

Unnecessary include.

> +#include <linux/i2c.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +#define LTC2992_CTRLB 0x01
> +#define LTC2992_FAULT1 0x03
> +#define LTC2992_POWER1 0x05
> +#define LTC2992_POWER1_MAX 0x08
> +#define LTC2992_POWER1_MIN 0x0B
> +#define LTC2992_POWER1_MAX_THRESH 0x0E
> +#define LTC2992_POWER1_MIN_THRESH 0x11
> +#define LTC2992_DSENSE1 0x14
> +#define LTC2992_DSENSE1_MAX 0x16
> +#define LTC2992_DSENSE1_MIN 0x18
> +#define LTC2992_DSENSE1_MAX_THRESH 0x1A
> +#define LTC2992_DSENSE1_MIN_THRESH 0x1C
> +#define LTC2992_SENSE1 0x1E
> +#define LTC2992_SENSE1_MAX 0x20
> +#define LTC2992_SENSE1_MIN 0x22
> +#define LTC2992_SENSE1_MAX_THRESH 0x24
> +#define LTC2992_SENSE1_MIN_THRESH 0x26
> +#define LTC2992_G1 0x28
> +#define LTC2992_G1_MAX 0x2A
> +#define LTC2992_G1_MIN 0x2C
> +#define LTC2992_G1_MAX_THRESH 0x2E
> +#define LTC2992_G1_MIN_THRESH 0x30
> +#define LTC2992_FAULT2 0x35
> +#define LTC2992_G2 0x5A
> +#define LTC2992_G2_MAX 0x5C
> +#define LTC2992_G2_MIN 0x5E
> +#define LTC2992_G2_MAX_THRESH 0x60
> +#define LTC2992_G2_MIN_THRESH 0x62
> +#define LTC2992_G3 0x64
> +#define LTC2992_G3_MAX 0x66
> +#define LTC2992_G3_MIN 0x68
> +#define LTC2992_G3_MAX_THRESH 0x6A
> +#define LTC2992_G3_MIN_THRESH 0x6C
> +#define LTC2992_G4 0x6E
> +#define LTC2992_G4_MAX 0x70
> +#define LTC2992_G4_MIN 0x72
> +#define LTC2992_G4_MAX_THRESH 0x74
> +#define LTC2992_G4_MIN_THRESH 0x76
> +#define LTC2992_FAULT3 0x92
> +
> +#define LTC2992_POWER(x) (LTC2992_POWER1 + ((x) * 0x32))
> +#define LTC2992_POWER_MAX(x) (LTC2992_POWER1_MAX + ((x) * 0x32))
> +#define LTC2992_POWER_MIN(x) (LTC2992_POWER1_MIN + ((x) * 0x32))
> +#define LTC2992_POWER_MAX_THRESH(x) (LTC2992_POWER1_MAX_THRESH + ((x) * 0x32))
> +#define LTC2992_POWER_MIN_THRESH(x) (LTC2992_POWER1_MIN_THRESH + ((x) * 0x32))
> +#define LTC2992_DSENSE(x) (LTC2992_DSENSE1 + ((x) * 0x32))
> +#define LTC2992_DSENSE_MAX(x) (LTC2992_DSENSE1_MAX + ((x) * 0x32))
> +#define LTC2992_DSENSE_MIN(x) (LTC2992_DSENSE1_MIN + ((x) * 0x32))
> +#define LTC2992_DSENSE_MAX_THRESH(x) (LTC2992_DSENSE1_MAX_THRESH + ((x) * 0x32))
> +#define LTC2992_DSENSE_MIN_THRESH(x) (LTC2992_DSENSE1_MIN_THRESH + ((x) * 0x32))
> +#define LTC2992_SENSE(x) (LTC2992_SENSE1 + ((x) * 0x32))
> +#define LTC2992_SENSE_MAX(x) (LTC2992_SENSE1_MAX + ((x) * 0x32))
> +#define LTC2992_SENSE_MIN(x) (LTC2992_SENSE1_MIN + ((x) * 0x32))
> +#define LTC2992_SENSE_MAX_THRESH(x) (LTC2992_SENSE1_MAX_THRESH + ((x) * 0x32))
> +#define LTC2992_SENSE_MIN_THRESH(x) (LTC2992_SENSE1_MIN_THRESH + ((x) * 0x32))
> +#define LTC2992_POWER_FAULT(x) (LTC2992_FAULT1 + ((x) * 0x32))
> +#define LTC2992_SENSE_FAULT(x) (LTC2992_FAULT1 + ((x) * 0x32))
> +#define LTC2992_DSENSE_FAULT(x) (LTC2992_FAULT1 + ((x) * 0x32))
> +
> +/* CTRLB register bitfields */
> +#define LTC2992_RESET_HISTORY BIT(3)
> +
> +/* FAULT1 FAULT2 registers common bitfields */
> +#define LTC2992_POWER_FAULT_MSK(x) (BIT(6) << (x))
> +#define LTC2992_DSENSE_FAULT_MSK(x) (BIT(4) << (x))
> +#define LTC2992_SENSE_FAULT_MSK(x) (BIT(2) << (x))
> +
> +/* FAULT1 bitfields */
> +#define LTC2992_GPIO1_FAULT_MSK(x) (BIT(0) << (x))
> +
> +/* FAULT2 bitfields */
> +#define LTC2992_GPIO2_FAULT_MSK(x) (BIT(0) << (x))
> +
> +/* FAULT3 bitfields */
> +#define LTC2992_GPIO3_FAULT_MSK(x) (BIT(6) << (x))
> +#define LTC2992_GPIO4_FAULT_MSK(x) (BIT(4) << (x))
> +
> +#define LTC2992_IADC_NANOV_LSB 12500
> +#define LTC2992_VADC_UV_LSB 25000
> +#define LTC2992_VADC_GPIO_UV_LSB 500
> +
> +struct ltc2992_state {
> + struct i2c_client *client;
> + struct regmap *regmap;
> + u32 r_sense_uohm[2];
> +};
> +
> +struct ltc2992_gpio_regs {
> + u8 data;
> + u8 max;
> + u8 min;
> + u8 max_thresh;
> + u8 min_thresh;
> + u8 alarm;
> + u8 min_alarm_msk;
> + u8 max_alarm_msk;
> +};
> +
> +static const struct ltc2992_gpio_regs ltc2992_gpio_addr_map[] = {
> + {
> + .data = LTC2992_G1,
> + .max = LTC2992_G1_MAX,
> + .min = LTC2992_G1_MIN,
> + .max_thresh = LTC2992_G1_MAX_THRESH,
> + .min_thresh = LTC2992_G1_MIN_THRESH,
> + .alarm = LTC2992_FAULT1,
> + .min_alarm_msk = LTC2992_GPIO1_FAULT_MSK(0),
> + .max_alarm_msk = LTC2992_GPIO1_FAULT_MSK(1),
> + },
> + {
> + .data = LTC2992_G2,
> + .max = LTC2992_G2_MAX,
> + .min = LTC2992_G2_MIN,
> + .max_thresh = LTC2992_G2_MAX_THRESH,
> + .min_thresh = LTC2992_G2_MIN_THRESH,
> + .alarm = LTC2992_FAULT2,
> + .min_alarm_msk = LTC2992_GPIO2_FAULT_MSK(0),
> + .max_alarm_msk = LTC2992_GPIO2_FAULT_MSK(1),
> + },
> + {
> + .data = LTC2992_G3,
> + .max = LTC2992_G3_MAX,
> + .min = LTC2992_G3_MIN,
> + .max_thresh = LTC2992_G3_MAX_THRESH,
> + .min_thresh = LTC2992_G3_MIN_THRESH,
> + .alarm = LTC2992_FAULT3,
> + .min_alarm_msk = LTC2992_GPIO3_FAULT_MSK(0),
> + .max_alarm_msk = LTC2992_GPIO3_FAULT_MSK(1),
> + },
> + {
> + .data = LTC2992_G4,
> + .max = LTC2992_G4_MAX,
> + .min = LTC2992_G4_MIN,
> + .max_thresh = LTC2992_G4_MAX_THRESH,
> + .min_thresh = LTC2992_G4_MIN_THRESH,
> + .alarm = LTC2992_FAULT3,
> + .min_alarm_msk = LTC2992_GPIO4_FAULT_MSK(0),
> + .max_alarm_msk = LTC2992_GPIO4_FAULT_MSK(1),
> + },
> +};
> +
> +static int ltc2992_read_reg(struct ltc2992_state *st, u8 addr, const u8 reg_len)
> +{
> + u8 regvals[4];
> + int ret;
> + int val;
> + int i;
> +
> + ret = regmap_bulk_read(st->regmap, addr, regvals, reg_len);
> + if (ret < 0)
> + return ret;
> +
> + val = 0;
> + for (i = 0; i < reg_len; i++)
> + val |= regvals[reg_len - i - 1] << (i * 8);
> +
> + return val;
> +}
> +
> +static int ltc2992_write_reg(struct ltc2992_state *st, u8 addr, const u8 reg_len, u32 val)
> +{
> + u8 regvals[4];
> + int i;
> +
> + for (i = 0; i < reg_len; i++)
> + regvals[reg_len - i - 1] = (val >> (i * 8)) & 0xFF;
> +
> + return regmap_bulk_write(st->regmap, addr, regvals, reg_len);
> +}
> +
> +static umode_t ltc2992_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr,
> + int channel)
> +{
> + const struct ltc2992_state *st = data;
> +
> + switch (type) {
> + case hwmon_chip:
> + switch (attr) {
> + case hwmon_chip_in_reset_history:
> + return 0200;
> + }
> + break;
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + case hwmon_in_lowest:
> + case hwmon_in_highest:
> + case hwmon_in_min_alarm:
> + case hwmon_in_max_alarm:
> + return 0444;
> + case hwmon_in_min:
> + case hwmon_in_max:
> + return 0644;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + case hwmon_curr_lowest:
> + case hwmon_curr_highest:
> + case hwmon_curr_min_alarm:
> + case hwmon_curr_max_alarm:
> + if (st->r_sense_uohm[channel])
> + return 0444;
> + break;
> + case hwmon_curr_min:
> + case hwmon_curr_max:
> + if (st->r_sense_uohm[channel])
> + return 0644;
> + break;
> + }
> + break;
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_input:
> + case hwmon_power_input_lowest:
> + case hwmon_power_input_highest:
> + case hwmon_power_min_alarm:
> + case hwmon_power_max_alarm:
> + if (st->r_sense_uohm[channel])
> + return 0444;
> + break;
> + case hwmon_power_min:
> + case hwmon_power_max:
> + if (st->r_sense_uohm[channel])
> + return 0644;
> + break;
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> +static int ltc2992_get_voltage(struct ltc2992_state *st, u32 reg, u32 scale, long *val)
> +{
> + int reg_val;
> +
> + reg_val = ltc2992_read_reg(st, reg, 2);
> + if (reg_val < 0)
> + return reg_val;
> +
> + reg_val = reg_val >> 4;
> + *val = DIV_ROUND_CLOSEST(reg_val * scale, 1000);
> +
> + return 0;
> +}
> +
> +static int ltc2992_set_voltage(struct ltc2992_state *st, u32 reg, u32 scale, long val)
> +{
> + val = DIV_ROUND_CLOSEST(val * 1000, scale);
> + val = val << 4;
> +
> + return ltc2992_write_reg(st, reg, 2, val);
> +}
> +
> +static int ltc2992_read_gpio_alarm(struct ltc2992_state *st, int nr_gpio, u32 attr, long *val)
> +{
> + int reg_val;
> + u32 mask;
> +
> + if (attr == hwmon_in_max_alarm)
> + mask = ltc2992_gpio_addr_map[nr_gpio].max_alarm_msk;
> + else
> + mask = ltc2992_gpio_addr_map[nr_gpio].min_alarm_msk;
> +
> + reg_val = ltc2992_read_reg(st, ltc2992_gpio_addr_map[nr_gpio].alarm, 1);
> + if (reg_val < 0)
> + return reg_val;
> +
> + *val = !!(reg_val & mask);
> + reg_val &= ~mask;
> +
> + return ltc2992_write_reg(st, ltc2992_gpio_addr_map[nr_gpio].alarm, 1, reg_val);
> +}
> +
> +static int ltc2992_read_gpios_in(struct device *dev, u32 attr, int nr_gpio, long *val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + switch (attr) {
> + case hwmon_in_input:
> + reg = ltc2992_gpio_addr_map[nr_gpio].data;
> + break;
> + case hwmon_in_lowest:
> + reg = ltc2992_gpio_addr_map[nr_gpio].min;
> + break;
> + case hwmon_in_highest:
> + reg = ltc2992_gpio_addr_map[nr_gpio].max;
> + break;
> + case hwmon_in_min:
> + reg = ltc2992_gpio_addr_map[nr_gpio].min_thresh;
> + break;
> + case hwmon_in_max:
> + reg = ltc2992_gpio_addr_map[nr_gpio].max_thresh;
> + break;
> + case hwmon_in_min_alarm:
> + case hwmon_in_max_alarm:
> + return ltc2992_read_gpio_alarm(st, nr_gpio, attr, val);
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_get_voltage(st, reg, LTC2992_VADC_GPIO_UV_LSB, val);
> +}
> +
> +static int ltc2992_read_in_alarm(struct ltc2992_state *st, int channel, long *val, u32 attr)
> +{
> + u32 reg_val;
> + u32 mask;
> +
> + if (attr == hwmon_in_max_alarm)
> + mask = LTC2992_SENSE_FAULT_MSK(1);
> + else
> + mask = LTC2992_SENSE_FAULT_MSK(0);
> +
> + reg_val = ltc2992_read_reg(st, LTC2992_SENSE_FAULT(channel), 1);
> + if (reg_val < 0)
> + return reg_val;
> +
> + *val = !!(reg_val & mask);
> + reg_val &= ~mask;
> +
> + return ltc2992_write_reg(st, LTC2992_SENSE_FAULT(channel), 1, reg_val);
> +}
> +
> +static int ltc2992_read_in(struct device *dev, u32 attr, int channel, long *val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + if (channel > 1)
> + return ltc2992_read_gpios_in(dev, attr, channel - 2, val);
> +
> + switch (attr) {
> + case hwmon_in_input:
> + reg = LTC2992_SENSE(channel);
> + break;
> + case hwmon_in_lowest:
> + reg = LTC2992_SENSE_MIN(channel);
> + break;
> + case hwmon_in_highest:
> + reg = LTC2992_SENSE_MAX(channel);
> + break;
> + case hwmon_in_min:
> + reg = LTC2992_SENSE_MIN_THRESH(channel);
> + break;
> + case hwmon_in_max:
> + reg = LTC2992_SENSE_MAX_THRESH(channel);
> + break;
> + case hwmon_in_min_alarm:
> + case hwmon_in_max_alarm:
> + return ltc2992_read_in_alarm(st, channel, val, attr);
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_get_voltage(st, reg, LTC2992_VADC_UV_LSB, val);
> +}
> +
> +static int ltc2992_get_current(struct ltc2992_state *st, u32 reg, u32 channel, long *val)
> +{
> + u32 reg_val;
> +
> + reg_val = ltc2992_read_reg(st, reg, 2);
> + if (reg_val < 0)
> + return reg_val;
> +
> + reg_val = reg_val >> 4;
> + *val = DIV_ROUND_CLOSEST(reg_val * LTC2992_IADC_NANOV_LSB, st->r_sense_uohm[channel]);
> +
> + return 0;
> +}
> +
> +static int ltc2992_set_current(struct ltc2992_state *st, u32 reg, u32 channel, long val)
> +{
> + u32 reg_val;
> +
> + reg_val = DIV_ROUND_CLOSEST(val * st->r_sense_uohm[channel], LTC2992_IADC_NANOV_LSB);
> + reg_val = reg_val << 4;
> +
> + return ltc2992_write_reg(st, reg, 2, reg_val);
> +}
> +
> +static int ltc2992_read_curr_alarm(struct ltc2992_state *st, int channel, long *val, u32 attr)
> +{
> + u32 reg_val;
> + u32 mask;
> +
> + if (attr == hwmon_curr_max_alarm)
> + mask = LTC2992_DSENSE_FAULT_MSK(1);
> + else
> + mask = LTC2992_DSENSE_FAULT_MSK(0);
> +
> + reg_val = ltc2992_read_reg(st, LTC2992_DSENSE_FAULT(channel), 1);
> + if (reg_val < 0)
> + return reg_val;
> +
> + *val = !!(reg_val & mask);
> +
> + reg_val &= ~mask;
> + return ltc2992_write_reg(st, LTC2992_DSENSE_FAULT(channel), 1, reg_val);
> +}
> +
> +static int ltc2992_read_curr(struct device *dev, u32 attr, int channel, long *val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + switch (attr) {
> + case hwmon_curr_input:
> + reg = LTC2992_DSENSE(channel);
> + break;
> + case hwmon_curr_lowest:
> + reg = LTC2992_DSENSE_MIN(channel);
> + break;
> + case hwmon_curr_highest:
> + reg = LTC2992_DSENSE_MAX(channel);
> + break;
> + case hwmon_curr_min:
> + reg = LTC2992_DSENSE_MIN_THRESH(channel);
> + break;
> + case hwmon_curr_max:
> + reg = LTC2992_DSENSE_MAX_THRESH(channel);
> + break;
> + case hwmon_curr_min_alarm:
> + case hwmon_curr_max_alarm:
> + return ltc2992_read_curr_alarm(st, channel, val, attr);
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_get_current(st, reg, channel, val);
> +}
> +
> +static int ltc2992_get_power(struct ltc2992_state *st, u32 reg, u32 channel, long *val)
> +{
> + u32 reg_val;
> +
> + reg_val = ltc2992_read_reg(st, reg, 3);
> + if (reg_val < 0)
> + return reg_val;
> +
> + *val = mul_u64_u32_div(reg_val, LTC2992_VADC_UV_LSB * LTC2992_IADC_NANOV_LSB,
> + st->r_sense_uohm[channel] * 1000);
> +
> + return 0;
> +}
> +
> +static int ltc2992_set_power(struct ltc2992_state *st, u32 reg, u32 channel, long val)
> +{
> + u32 reg_val;
> +
> + reg_val = mul_u64_u32_div(val, st->r_sense_uohm[channel] * 1000,
> + LTC2992_VADC_UV_LSB * LTC2992_IADC_NANOV_LSB);
> +
> + return ltc2992_write_reg(st, reg, 3, reg_val);
> +}
> +
> +static int ltc2992_read_power_alarm(struct ltc2992_state *st, int channel, long *val, u32 attr)
> +{
> + u32 reg_val;
> + u32 mask;
> +
> + if (attr == hwmon_power_max_alarm)
> + mask = LTC2992_POWER_FAULT_MSK(1);
> + else
> + mask = LTC2992_POWER_FAULT_MSK(0);
> +
> + reg_val = ltc2992_read_reg(st, LTC2992_POWER_FAULT(channel), 1);
> + if (reg_val < 0)
> + return reg_val;
> +
> + *val = !!(reg_val & mask);
> + reg_val &= ~mask;
> +
> + return ltc2992_write_reg(st, LTC2992_POWER_FAULT(channel), 1, reg_val);
> +}
> +
> +static int ltc2992_read_power(struct device *dev, u32 attr, int channel, long *val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + switch (attr) {
> + case hwmon_power_input:
> + reg = LTC2992_POWER(channel);
> + break;
> + case hwmon_power_input_lowest:
> + reg = LTC2992_POWER_MIN(channel);
> + break;
> + case hwmon_power_input_highest:
> + reg = LTC2992_POWER_MAX(channel);
> + break;
> + case hwmon_power_min:
> + reg = LTC2992_POWER_MIN_THRESH(channel);
> + break;
> + case hwmon_power_max:
> + reg = LTC2992_POWER_MAX_THRESH(channel);
> + break;
> + case hwmon_power_min_alarm:
> + case hwmon_power_max_alarm:
> + return ltc2992_read_power_alarm(st, channel, val, attr);
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_get_power(st, reg, channel, val);
> +}
> +
> +static int ltc2992_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel,
> + long *val)
> +{
> + switch (type) {
> + case hwmon_in:
> + return ltc2992_read_in(dev, attr, channel, val);
> + case hwmon_curr:
> + return ltc2992_read_curr(dev, attr, channel, val);
> + case hwmon_power:
> + return ltc2992_read_power(dev, attr, channel, val);
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static int ltc2992_write_curr(struct device *dev, u32 attr, int channel, long val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + switch (attr) {
> + case hwmon_curr_min:
> + reg = LTC2992_DSENSE_MIN_THRESH(channel);
> + break;
> + case hwmon_curr_max:
> + reg = LTC2992_DSENSE_MAX_THRESH(channel);
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_set_current(st, reg, channel, val);
> +}
> +
> +static int ltc2992_write_gpios_in(struct device *dev, u32 attr, int nr_gpio, long val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg;
> +
> + switch (attr) {
> + case hwmon_in_min:
> + reg = ltc2992_gpio_addr_map[nr_gpio].min_thresh;
> + break;
> + case hwmon_in_max:
> + reg = ltc2992_gpio_addr_map[nr_gpio].max_thresh;
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_set_voltage(st, reg, LTC2992_VADC_GPIO_UV_LSB, val);
> +}
> +
> +static int ltc2992_write_in(struct device *dev, u32 attr, int channel, long val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg = 0;

Unnecessary initialization.

> +
> + if (channel > 1)
> + return ltc2992_write_gpios_in(dev, attr, channel - 2, val);
> +
> + switch (attr) {
> + case hwmon_in_min:
> + reg = LTC2992_SENSE_MIN_THRESH(channel);
> + break;
> + case hwmon_in_max:
> + reg = LTC2992_SENSE_MAX_THRESH(channel);
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_set_voltage(st, reg, LTC2992_VADC_UV_LSB, val);
> +}
> +
> +static int ltc2992_write_power(struct device *dev, u32 attr, int channel, long val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> + u32 reg = 0;

Unnecessary initialization.

> +
> + switch (attr) {
> + case hwmon_power_min:
> + reg = LTC2992_POWER_MIN_THRESH(channel);
> + break;
> + case hwmon_power_max:
> + reg = LTC2992_POWER_MAX_THRESH(channel);
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + return ltc2992_set_power(st, reg, channel, val);
> +}
> +
> +static int ltc2992_write_chip(struct device *dev, u32 attr, int channel, long val)
> +{
> + struct ltc2992_state *st = dev_get_drvdata(dev);
> +
> + switch (attr) {
> + case hwmon_chip_in_reset_history:
> + return regmap_update_bits(st->regmap, LTC2992_CTRLB, LTC2992_RESET_HISTORY,
> + LTC2992_RESET_HISTORY);
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static int ltc2992_write(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel,
> + long val)
> +{
> + switch (type) {
> + case hwmon_chip:
> + return ltc2992_write_chip(dev, attr, channel, val);
> + case hwmon_in:
> + return ltc2992_write_in(dev, attr, channel, val);
> + case hwmon_curr:
> + return ltc2992_write_curr(dev, attr, channel, val);
> + case hwmon_power:
> + return ltc2992_write_power(dev, attr, channel, val);
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static const struct hwmon_ops ltc2992_hwmon_ops = {
> + .is_visible = ltc2992_is_visible,
> + .read = ltc2992_read,
> + .write = ltc2992_write,
> +};
> +
> +static const u32 ltc2992_chip_config[] = {
> + HWMON_C_IN_RESET_HISTORY,
> + 0
> +};
> +
> +static const struct hwmon_channel_info ltc2992_chip = {
> + .type = hwmon_chip,
> + .config = ltc2992_chip_config,
> +};
> +
> +static const u32 ltc2992_in_config[] = {
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | HWMON_I_MIN | HWMON_I_MAX |
> + HWMON_I_MIN_ALARM | HWMON_I_MAX_ALARM,
> + 0
> +};
> +
> +static const struct hwmon_channel_info ltc2992_in = {
> + .type = hwmon_in,
> + .config = ltc2992_in_config,
> +};
> +
> +static const u32 ltc2992_curr_config[] = {
> + HWMON_C_INPUT | HWMON_C_LOWEST | HWMON_C_HIGHEST | HWMON_C_MIN | HWMON_C_MAX |
> + HWMON_C_MIN_ALARM | HWMON_C_MAX_ALARM,
> + HWMON_C_INPUT | HWMON_C_LOWEST | HWMON_C_HIGHEST | HWMON_C_MIN | HWMON_C_MAX |
> + HWMON_C_MIN_ALARM | HWMON_C_MAX_ALARM,
> + 0
> +};
> +
> +static const struct hwmon_channel_info ltc2992_curr = {
> + .type = hwmon_curr,
> + .config = ltc2992_curr_config,
> +};
> +
> +static const u32 ltc2992_power_config[] = {
> + HWMON_P_INPUT | HWMON_P_INPUT_LOWEST | HWMON_P_INPUT_HIGHEST | HWMON_P_MIN | HWMON_P_MAX |
> + HWMON_P_MIN_ALARM | HWMON_P_MAX_ALARM,
> + HWMON_P_INPUT | HWMON_P_INPUT_LOWEST | HWMON_P_INPUT_HIGHEST | HWMON_P_MIN | HWMON_P_MAX |
> + HWMON_P_MIN_ALARM | HWMON_P_MAX_ALARM,
> + 0
> +};
> +
> +static const struct hwmon_channel_info ltc2992_power = {
> + .type = hwmon_power,
> + .config = ltc2992_power_config,
> +};
> +
> +static const struct hwmon_channel_info *ltc2992_info[] = {
> + &ltc2992_chip,
> + &ltc2992_in,
> + &ltc2992_curr,
> + &ltc2992_power,
> + NULL
> +};
> +
> +static const struct hwmon_chip_info ltc2992_chip_info = {
> + .ops = &ltc2992_hwmon_ops,
> + .info = ltc2992_info,
> +};
> +
> +static const struct regmap_config ltc2992_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = 0xE8,
> +};
> +
> +static int ltc2992_parse_dt(struct ltc2992_state *st)
> +{
> + struct fwnode_handle *fwnode;
> + struct fwnode_handle *child;
> + u32 addr;
> + u32 val;
> + int ret;
> +
> + fwnode = dev_fwnode(&st->client->dev);
> +
> + fwnode_for_each_available_child_node(fwnode, child) {
> + ret = fwnode_property_read_u32(child, "reg", &addr);
> + if (ret < 0)
> + return ret;
> +
> + if (addr > 1)
> + return -EINVAL;
> +
> + ret = fwnode_property_read_u32(child, "shunt-resistor-micro-ohms", &val);
> + if (!ret)
> + st->r_sense_uohm[addr] = val;
> + }
> +
> + return 0;
> +}
> +
> +static int ltc2992_i2c_probe(struct i2c_client *client, const struct i2c_device_id *id)
> +{
> + struct device *hwmon_dev;
> + struct ltc2992_state *st;
> + int ret;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> + return -ENODEV;

This shuld be unnecesssary. It only really makes sense if there are direct
i2c reads and for special functions like reading block data.

> +
> + st = devm_kzalloc(&client->dev, sizeof(*st), GFP_KERNEL);
> + if (!st)
> + return -ENOMEM;
> +
> + st->client = client;
> + st->regmap = devm_regmap_init_i2c(client, &ltc2992_regmap_config);
> + if (IS_ERR(st->regmap))
> + return PTR_ERR(st->regmap);
> +
> + ret = ltc2992_parse_dt(st);
> + if (ret < 0)
> + return ret;
> +
> + hwmon_dev = devm_hwmon_device_register_with_info(&client->dev, client->name, st,
> + &ltc2992_chip_info, NULL);
> +
> + return PTR_ERR_OR_ZERO(hwmon_dev);
> +}
> +
> +static const struct of_device_id ltc2992_of_match[] = {
> + { .compatible = "adi,ltc2992" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, ltc2992_of_match);
> +
> +static const struct i2c_device_id ltc2992_i2c_id[] = {
> + {"ltc2992", 0},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, ltc2992_i2c_id);
> +
> +static struct i2c_driver ltc2992_i2c_driver = {
> + .driver = {
> + .name = "ltc2992",
> + .of_match_table = ltc2992_of_match,
> + },
> + .probe = ltc2992_i2c_probe,
> + .id_table = ltc2992_i2c_id,
> +};
> +
> +module_i2c_driver(ltc2992_i2c_driver);
> +
> +MODULE_AUTHOR("Alexandru Tachici <alexandru.tachici@analog.com>");
> +MODULE_DESCRIPTION("Hwmon driver for Linear Technology 2992");
> +MODULE_LICENSE("Dual BSD/GPL");

\
 
 \ /
  Last update: 2020-11-22 17:03    [W:0.092 / U:0.872 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site