lkml.org 
[lkml]   [2020]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 00/16] Tegra XHCI controller ELPG support
From
Date

On 11/14/20 12:44 AM, Thierry Reding wrote:
> On Fri, Oct 16, 2020 at 09:07:10PM +0800, JC Kuo wrote:
>> Tegra XHCI controler can be placed in ELPG (Engine Level PowerGated)
>> state for power saving when all of the connected USB devices are in
>> suspended state. This patch series includes clk, phy and pmc changes
>> that are required for properly place controller in ELPG and bring
>> controller out of ELPG.
>>
>> JC Kuo (16):
>> clk: tegra: Add PLLE HW power sequencer control
>> clk: tegra: Don't enable PLLE HW sequencer at init
>> phy: tegra: xusb: Move usb3 port init for Tegra210
>> phy: tegra: xusb: tegra210: Do not reset UPHY PLL
>> phy: tegra: xusb: Rearrange UPHY init on Tegra210
>> phy: tegra: xusb: Add Tegra210 lane_iddq operation
>> phy: tegra: xusb: Add sleepwalk and suspend/resume
>> soc/tegra: pmc: Provide USB sleepwalk register map
>> arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop
>> dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop
>> phy: tegra: xusb: Add wake/sleepwalk for Tegra210
>> phy: tegra: xusb: Tegra210 host mode VBUS control
>> phy: tegra: xusb: Add wake/sleepwalk for Tegra186
>> arm64: tegra210/tegra186/tegra194: XUSB PADCTL irq
>> usb: host: xhci-tegra: Unlink power domain devices
>> xhci: tegra: Enable ELPG for runtime/system PM
>>
>> .../phy/nvidia,tegra124-xusb-padctl.txt | 1 +
>> arch/arm64/boot/dts/nvidia/tegra186.dtsi | 1 +
>> arch/arm64/boot/dts/nvidia/tegra194.dtsi | 1 +
>> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 2 +
>> drivers/clk/tegra/clk-pll.c | 12 -
>> drivers/clk/tegra/clk-tegra210.c | 53 +-
>> drivers/phy/tegra/xusb-tegra186.c | 558 ++++-
>> drivers/phy/tegra/xusb-tegra210.c | 1889 +++++++++++++----
>> drivers/phy/tegra/xusb.c | 92 +-
>> drivers/phy/tegra/xusb.h | 22 +-
>> drivers/soc/tegra/pmc.c | 94 +
>> drivers/usb/host/xhci-tegra.c | 610 ++++--
>> include/linux/clk/tegra.h | 4 +-
>> include/linux/phy/tegra/xusb.h | 10 +-
>> 14 files changed, 2785 insertions(+), 564 deletions(-)
>
> I've been testing this, but I keep seeing the following oops on suspend
> on a Jetson TX1:
>
> [ 153.451108] tegra-xusb-padctl phy-usb2.0: > tegra_xusb_padctl_suspend_noirq(dev=ffff000080917000)
> [ 153.460353] tegra-xusb-padctl phy-usb2.0: driver: ffff8000114453e0 (tegra_xusb_padctl_driver)
> [ 153.469245] tegra-xusb-padctl phy-usb2.0: padctl: ffff0000829f6480
> [ 153.475772] tegra-xusb-padctl phy-usb2.0: soc: ef7bdd7fffffffff (0xef7bdd7fffffffff)
> [ 153.484061] Unable to handle kernel paging request at virtual address 007bdd800000004f
> [ 153.492132] Mem abort info:
> [ 153.495083] ESR = 0x96000004
> [ 153.498308] EC = 0x25: DABT (current EL), IL = 32 bits
> [ 153.503771] SET = 0, FnV = 0
> [ 153.506979] EA = 0, S1PTW = 0
> [ 153.510260] Data abort info:
> [ 153.513200] ISV = 0, ISS = 0x00000004
> [ 153.517181] CM = 0, WnR = 0
> [ 153.520302] [007bdd800000004f] address between user and kernel address ranges
> [ 153.527600] Internal error: Oops: 96000004 [#1] PREEMPT SMP
> [ 153.533231] Modules linked in: nouveau panel_simple tegra_video(C) tegra_drm drm_ttm_helper videobuf2_dma_contig ttm videobuf2_memops cec videobuf2_v4l2 videobuf2_common drm_kms_helper v4l2_fwnode videodev drm mc snd_hda_codec_hdmi cdc_ether usbnet snd_hda_tegra r8152 crct10dif_ce snd_hda_codec snd_hda_core tegra_xudc host1x lp855x_bl at24 ip_tables x_tables ipv6
> [ 153.566417] CPU: 0 PID: 300 Comm: systemd-sleep Tainted: G C 5.10.0-rc3-next-20201113-00019-g5c064d5372b0-dirty #624
> [ 153.578283] Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)
> [ 153.584281] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
> [ 153.590381] pc : tegra_xusb_padctl_suspend_noirq+0x88/0x100
> [ 153.596016] lr : tegra_xusb_padctl_suspend_noirq+0x80/0x100
> [ 153.601632] sp : ffff8000120dbb60
> [ 153.604999] x29: ffff8000120dbb60 x28: ffff000080a1df00
> [ 153.610430] x27: 0000000000000002 x26: ffff8000106f8540
> [ 153.615858] x25: ffff8000113ac4a4 x24: ffff80001148c198
> [ 153.621277] x23: ffff800010c4538c x22: 0000000000000002
> [ 153.626692] x21: ffff800010ccde80 x20: ffff0000829f6480
> [ 153.632107] x19: ffff000080917000 x18: 0000000000000030
> [ 153.637521] x17: 0000000000000000 x16: 0000000000000000
> [ 153.642933] x15: ffff000080a1e380 x14: 74636461702d6273
> [ 153.648346] x13: ffff8000113ad058 x12: 0000000000000f39
> [ 153.653759] x11: 0000000000000513 x10: ffff800011405058
> [ 153.659176] x9 : 00000000fffff000 x8 : ffff8000113ad058
> [ 153.664590] x7 : ffff800011405058 x6 : 0000000000000000
> [ 153.670002] x5 : 0000000000000000 x4 : ffff0000fe908bc0
> [ 153.675414] x3 : ffff0000fe910228 x2 : 162ef67e0581e700
> [ 153.680826] x1 : 162ef67e0581e700 x0 : ef7bdd7fffffffff
> [ 153.686241] Call trace:
> [ 153.688769] tegra_xusb_padctl_suspend_noirq+0x88/0x100
> [ 153.694077] __device_suspend_noirq+0x68/0x1cc
> [ 153.698594] dpm_noirq_suspend_devices+0x10c/0x1d0
> [ 153.703456] dpm_suspend_noirq+0x28/0xa0
> [ 153.707461] suspend_devices_and_enter+0x234/0x4bc
> [ 153.712314] pm_suspend+0x1e4/0x270
> [ 153.715868] state_store+0x8c/0x110
> [ 153.719440] kobj_attr_store+0x1c/0x30
> [ 153.723259] sysfs_kf_write+0x4c/0x7c
> [ 153.726981] kernfs_fop_write+0x124/0x240
> [ 153.731065] vfs_write+0xe4/0x204
> [ 153.734449] ksys_write+0x6c/0x100
> [ 153.737925] __arm64_sys_write+0x20/0x30
> [ 153.741931] el0_svc_common.constprop.0+0x78/0x1a0
> [ 153.746789] do_el0_svc+0x24/0x90
> [ 153.750181] el0_sync_handler+0x254/0x260
> [ 153.754251] el0_sync+0x174/0x180
> [ 153.757663] Code: aa0303e2 94000f64 f9405680 b40000e0 (f9402803)
> [ 153.763826] ---[ end trace 81543a3394cb409d ]---
>
> Note that I've added a bit of debug information there to show what's
> going on. See how tegra_xusb_padctl_suspend_noirq() is being called for
> the phy-usb2.0 device? That's one of the PHYs that's being created for
> the USB2 lanes. Sometimes I do see that padctl->soc ends up being NULL
> for that device and in that case the function just aborts early and then
> tegra_xusb_padctl_suspend_noirq() will get called again for the padctl
> device and succeed.
>
> I can't explain what's happening here. tegra_xusb_padctl_driver never
> binds to the phy-usb2.0 device, so I don't understand how it could end
> up suspending the device with that set of dev_pm_ops. Perhaps this is
> some weird type of corruption somewhere?
>
> Thierry
>

Hi Thierry,
I figured out that phy-usb2.0 device is bound to tegra-xusb-padctl driver by
those two lines in tegra_xusb_setup_usb_role_switch()

port->usb_phy.dev = &lane->pad->lanes[port->index]->dev;
port->usb_phy.dev->driver = port->padctl->dev->driver;

Instead of assigning lane (phy) device to 'struct usb_phy', I think it should be
the port device (port->dev) since the 'usb-role-switch' capability belongs to
port device.

port->usb_phy.dev = &port->dev;

I will submit a patch and ask for your review.

Thanks,
JC

\
 
 \ /
  Last update: 2020-11-17 07:15    [W:0.145 / U:2.428 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site