lkml.org 
[lkml]   [2020]   [Oct]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 1/2] dt-bindings: usb: Add binding for discrete onboard USB hubs
On Wed, Oct 07, 2020 at 03:25:42PM -0400, Alan Stern wrote:
> On Wed, Oct 07, 2020 at 10:28:47AM -0700, Matthias Kaehlcke wrote:
> > On Wed, Oct 07, 2020 at 12:38:38PM -0400, Alan Stern wrote:
> > > On Wed, Oct 07, 2020 at 09:03:36AM -0700, Matthias Kaehlcke wrote:
> > > > Ok, I wasn't sure if the hubs suspend asynchronously from each other. If they
> > > > do it should indeed not be a problem to have the "master" wait for its peers.
> > >
> > > Well, order of suspending is selectable by the user. It can be either
> > > asynchronous or reverse order of device registration, which might pose a
> > > problem. We don't know in advance which of two peer hubs will be
> > > registered first. It might be necessary to introduce some additional
> > > explicit synchronization.
> >
> > I'm not sure we are understanding each other completely. I agree that
> > synchronization is needed to have the primary hub wait for its peers, that
> > was one of my initial concerns.
> >
> > Lets use an example to clarify my secondary concern: a hub chip provides a
> > USB 3 and a USB 2 hub, lets say the USB 3 hub is the primary.
> >
> > Here is some pseudo-code for the suspend function:
> >
> > hub_suspend(hub)
> > ...
> >
> > if (hub->primary) {
> > device_pm_wait_for_dev(hub->peer)
> >
> > // check for connected devices and turn regulator off
> > }
> >
> > ...
> > }
> >
> > What I meant with 'asynchronous suspend' in this context:
> >
> > Can hub_suspend() of the peer hub be executed (asynchronously) while the
> > primary is blocked on device_pm_wait_for_dev(),
>
> Yes, that's exactly what would happen with async suspend.
>
> > or would the primary wait
> > forever if the peer hub isn't suspended yet?
>
> That wouldn't happen. device_pm_wait_for_dev is smart; it will return
> immediately if neither device uses async suspend. But in that case you
> could end up removing power from the peer hub before it had suspended.
>
> That's why I said you might need to add additional synchronization. The
> suspend routines for the two hubs could each check to see whether the
> other device had suspended yet, and the last one would handle the power
> regulator. The additional synchronization is for the case where the two
> checks end up being concurrent.

That was exactly my initial concern and one of the reasons I favor(ed) a
platform instead of a USB driver:

> otherwise all hubs need to know their peers and check in suspend if they
> are the last hub standing, only then the power can be switched off.

To which you replied:

> you just need to make the "master" hub wait for its peer to suspend, which
> is easy to do.

However that apparently only works if async suspend is enabled, and we
can't rely on that.

With the peers checking on each other you lose effectively the notion
of a primary.

Going back to the binding:

&usb_1_dwc3 {
hub_2_0: hub@1 {
compatible = "usbbda,5411";
reg = <1>;
};

hub_3_0: hub@2 {
compatible = "usbbda,411";
reg = <2>;
vdd-supply = <&pp3300_hub>;
companion-hubs = <&hub_2_0>;
};
};

How does 'hub_2_0' know that its peer is hub_3_0 and that it has a regulator
(and potentially other resources)?

All this mess can be avoided by having a single instance in control of the
resources which is guaranteed to suspend after the USB devices.

\
 
 \ /
  Last update: 2020-10-07 21:43    [W:0.938 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site