lkml.org 
[lkml]   [2020]   [Oct]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 2/2] Add hardware monitoring driver for Moortec MR75203 PVT controller
On Mon, Oct 5, 2020 at 11:53 AM Tanwar, Rahul
<rahul.tanwar@linux.intel.com> wrote:
> On 3/10/2020 2:11 am, Andy Shevchenko wrote:
> > On Fri, Oct 02, 2020 at 03:04:27PM +0800, Rahul Tanwar wrote:

...

> >> + pvt_temp.config = temp_config;
> >> +
> >> + pvt_info[index++] = &pvt_temp;
> >> + }
> >> +
> >> + if (pd_num) {
> >> + ret = pvt_get_regmap(pdev, "pd", pvt);
> >> + if (ret)
> >> + return ret;
> >> + }
> >> +
> >> + if (vm_num) {
> >> + u32 num = vm_num;
> >> +
> >> + ret = pvt_get_regmap(pdev, "vm", pvt);
> >> + if (ret)
> >> + return ret;
> >> +
> >> + pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx),
> >> + GFP_KERNEL);
> >> + if (!pvt->vm_idx)
> >> + return -ENOMEM;
> >> + for (i = 0; i < vm_num; i++)
> >> + pvt->vm_idx[i] = i;
> > What the point if you are replace them below in one case?
> >
> >> + ret = device_property_read_u8_array(dev, "intel,vm-map",
> >> + pvt->vm_idx, vm_num);
> >> + if (!ret)
> > Misses {} and because of above
> >
> > if (ret) {
> > for () ...
> > } else {
> > for () ...
> > }
> >
> >> + for (i = 0; i < vm_num; i++)
> >> + if (pvt->vm_idx[i] >= vm_num ||
> >> + pvt->vm_idx[i] == 0xff) {
> >> + num = i;
> >> + break;
> >> + }
> > Or looking in this, perhaps move the incremental for-loop here and start it
> > with num which is 0.
>
> Not able to understand what exactly you are suggesting here. Presently
> it is like below:
> 1. Init vm_idx array with incremental values.
> 2. Read array from device property.
> 3. If success, figure out the last valid value and assign to num.
>
> Can you please elaborate and explain more clearly? Thanks.

device_property_read_u8_array() effectively (partially) rewrites the
vm_idx array.
The code above is inefficient and not clear.
My understanding based on the above is that half of the code may be dropped.

So, clearer variant looks like this to me:

ret = device_property_read_u8_array(dev, "intel,vm-map", pvt->vm_idx, vm_num);
if (ret) {
num = 0;
} else {
for (i = 0; i < vm_num; i++) {
if (pvt->vm_idx[i] >= vm_num || pvt->vm_idx[i] == 0xff)
break;
}
num = i;
}
for (i = num; i < vm_num; i++)
pvt->vm_idx[i] = i;

And all these require a good comment to describe why you are doing the
trailing loop.

--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2020-10-05 11:07    [W:1.632 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site