lkml.org 
[lkml]   [2020]   [Oct]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v11 01/14] s390/vfio-ap: No need to disable IRQ after queue reset
On Thu, 29 Oct 2020 19:29:35 -0400
Tony Krowiak <akrowiak@linux.ibm.com> wrote:

> >> @@ -1177,7 +1166,10 @@ static int vfio_ap_mdev_reset_queues(struct mdev_device *mdev)
> >> */
> >> if (ret)
> >> rc = ret;
> >> - vfio_ap_irq_disable_apqn(AP_MKQID(apid, apqi));
> >> + q = vfio_ap_get_queue(matrix_mdev,
> >> + AP_MKQID(apid, apqi));
> >> + if (q)
> >> + vfio_ap_free_aqic_resources(q);
> > Is it safe to do vfio_ap_free_aqic_resources() at this point? I don't
> > think so. I mean does the current code (and vfio_ap_mdev_reset_queue()
> > in particular guarantee that the reset is actually done when we arrive
> > here)? BTW, I think we have a similar problem with the current code as
> > well.
>
> If the return code from the vfio_ap_mdev_reset_queue() function
> is zero, then yes, we are guaranteed the reset was done and the
> queue is empty.

I've read up on this and I disagree. We should discuss this offline.

>  The function returns a non-zero return code if
> the reset fails or the queue the reset did not complete within a given
> amount of time, so maybe we shouldn't free AQIC resources when
> we get a non-zero return code from the reset function?
>

If the queue is gone, or broken, it won't produce interrupts or poke the
notifier bit, and we should clean up the AQIC resources.


> There are three occasions when the vfio_ap_mdev_reset_queues()
> is called:
> 1. When the VFIO_DEVICE_RESET ioctl is invoked from userspace
>     (i.e., when the guest is started)
> 2. When the mdev fd is closed (vfio_ap_mdev_release())
> 3. When the mdev is removed (vfio_ap_mdev_remove())
>
> The IRQ resources are initialized when the PQAP(AQIC)
> is intercepted to enable interrupts. This would occur after
> the guest boots and the AP bus initializes. So, 1 would
> presumably occur before that happens. I couldn't find
> anywhere in the AP bus or zcrypt code where a PQAP(AQIC)
> is executed to disable interrupts, so my assumption is
> that IRQ disablement is accomplished by a reset on
> the guest. I'll have to ask Harald about that. So, 2 would
> occur when the guest is about to terminate and 3
> would occur only after the guest is terminated. In any
> case, it seems that IRQ resources should be cleaned up.
> Maybe it would be more appropriate to do that in the
> vfio_ap_mdev_release() and vfio_ap_mdev_remove()
> functions themselves?

I'm a bit confused. But I think you are wrong. What happens when the
guest reIPLs? I guess the subsystem reset should also do the
VFIO_DEVICE_RESET ioctl, and that has to reset the queues and disable
the interrupts. Or?

Regards,
Halil

\
 
 \ /
  Last update: 2020-10-30 18:43    [W:0.117 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site