lkml.org 
[lkml]   [2020]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 0/2] PCI: aardvark: Fix comphy with old ATF
On Friday 02 October 2020 16:03:09 Lorenzo Pieralisi wrote:
> On Fri, Oct 02, 2020 at 04:52:37PM +0200, Pali Rohár wrote:
> > On Friday 02 October 2020 15:38:51 Lorenzo Pieralisi wrote:
> > > On Fri, Oct 02, 2020 at 04:26:16PM +0200, Pali Rohár wrote:
> > > > On Friday 02 October 2020 14:37:13 Lorenzo Pieralisi wrote:
> > > > > On Wed, Sep 02, 2020 at 04:43:42PM +0200, Pali Rohár wrote:
> > > > > > This patch series fixes regression introduced in commit 366697018c9a
> > > > > > ("PCI: aardvark: Add PHY support") which caused aardvark driver
> > > > > > initialization failure on EspressoBin board with factory version of
> > > > > > Arm Trusted Firmware provided by Marvell.
> > > > > >
> > > > > > Second patch depends on the first patch, so please add appropriate
> > > > > > Fixes/Cc:stable@ tags to have both patches correctly backported to
> > > > > > stable kernels.
> > > > > >
> > > > > > I have tested both patches with Marvell ATF firmware ebin-17.10-uart.zip
> > > > > > and with upstream ATF+uboot and aardvark was initialized successfully.
> > > > > > Without this patch series on ebin-17.10-uart.zip aardvark initialization
> > > > > > failed.
> > > > > >
> > > > > > Pali Rohár (2):
> > > > > > phy: marvell: comphy: Convert internal SMCC firmware return codes to
> > > > > > errno
> > > > > > PCI: aardvark: Fix initialization with old Marvell's Arm Trusted
> > > > > > Firmware
> > > > > >
> > > > > > drivers/pci/controller/pci-aardvark.c | 4 +++-
> > > > > > drivers/phy/marvell/phy-mvebu-a3700-comphy.c | 14 +++++++++++---
> > > > > > drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 14 +++++++++++---
> > > > > > 3 files changed, 25 insertions(+), 7 deletions(-)
> > > > >
> > > > > Applied to pci/aardvark (both patches), thanks.
> > > >
> > > > Ok! For second patch would be needed to put CC:stable line with
> > > > specifying prerequisite of first patch as written in document:
> > > >
> > > > https://www.kernel.org/doc/html/latest/process/stable-kernel-rules.html
> > > >
> > > > If I understood it correctly, second patch needs following line:
> > > >
> > > > Cc: <stable@vger.kernel.org> # <commit_id_of_first_path>: comphy: errno return codes
> > > >
> > > > where <commit_id_of_first_path> is commit id of PATCH 1/2.
> > > >
> > > > (correct me if I'm wrong)
> > > >
> > > > Now when first commit has commit id, could you update second commit to
> > > > include this information about prerequisite?
> > >
> > > No I can't because they will be merged at the same time.
> >
> > And it is a problem? Git commit id of first patch would not be changed,
> > so referencing to it is now possible from second commit (unless you do
> > rebasing).
> >
> > > What we can do is mark the second patch for stable
> >
> > This is done by adding "Cc: <stable@vger.kernel.org>" line to second
> > patch which I suggested, right?
>
> I will apply the stable tag and dependency, it should be fine.

Ok! I thought that according to stable-kernel-rules.html that dependent
commit could be added after stable email address separated with # char.
At least this is how I understood stable-kernel-rules.html and its
section:

"Additionally, some patches submitted via Option 1 may have additional
patch prerequisites which can be cherry-picked."

> Please ensure you follow up stable updates especially in case patches
> don't backport properly (ie please try).

No problem, I can monitor emails about backporting these patches.

> Lorenzo

\
 
 \ /
  Last update: 2020-10-02 17:08    [W:0.228 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site