Messages in this thread | | | Subject | Re: [PATCH 1/2] thermal: power allocator: change the 'k_i' coefficient estimation | From | Lukasz Luba <> | Date | Tue, 13 Oct 2020 11:59:42 +0100 |
| |
Hi Daniel,
On 10/13/20 11:21 AM, Daniel Lezcano wrote: > > Hi Lukasz, > > On 02/10/2020 14:24, Lukasz Luba wrote: >> Intelligent Power Allocation (IPA) is built around the PID controller >> concept. The initialization code tries to setup the environment based on >> the information available in DT or estimate the value based on minimum >> power reported by each of the cooling device. The estimation will have an >> impact on the PID controller behaviour via the related 'k_po', 'k_pu', >> 'k_i' coefficients and also on the power budget calculation. >> >> This change prevents the situation when 'k_i' is relatively big compared >> to 'k_po' and 'k_pu' values. This might happen when the estimation for >> 'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are >> small. >> >> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> >> --- >> drivers/thermal/gov_power_allocator.c | 8 ++++++-- >> 1 file changed, 6 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c >> index 5cb518d8f156..f69fafe486a5 100644 >> --- a/drivers/thermal/gov_power_allocator.c >> +++ b/drivers/thermal/gov_power_allocator.c >> @@ -131,6 +131,7 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, >> int ret; >> int switch_on_temp; >> u32 temperature_threshold; >> + s32 k_i; >> >> ret = tz->ops->get_trip_temp(tz, trip_switch_on, &switch_on_temp); >> if (ret) >> @@ -156,8 +157,11 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, >> tz->tzp->k_pu = int_to_frac(2 * sustainable_power) / >> temperature_threshold; >> >> - if (!tz->tzp->k_i || force) >> - tz->tzp->k_i = int_to_frac(10) / 1000; >> + if (!tz->tzp->k_i || force) { >> + k_i = tz->tzp->k_pu / 10; >> + tz->tzp->k_i = k_i > 0 ? k_i : 1; >> + } > > I do not understand the rational behind this change.
This is the unfortunate impact of the EM abstract scale of power values. IPA didn't have to deal with it, because we always had milli-Watts. Because the EM allows the bogoWatts and some vendors already have them I have to re-evaluate the IPA.
> > Do you have some values to share describing what would be the impact of > this change?
Yes, here is an example: EM has 3 devices with abstract scale power values, where minimum power is 25 and max is 200. The minimum power is used by estimate_sustainable_power() as a sum of all devices' min power. Sustainable power is going to be estimated to 75.
Then in the code we have 'temperature_threshold' which is in milli-Celcius, thus 15degC is 15000.
We estimate 'k_po' according to: int_to_frac(sustainable_power) / temperature_threshold;
which is: (75 << 10) / 15000 = ~75000 / 15000 = 5 <-- 'k_po'
then k_pu: ((2*75) << 10) / 15000 = ~150000 / 15000 = 10
Then the old 'k_i' is just hard-coded 10, which is the same order of magnitude to what is in 'k_pu'. It should be 1 order of magnitude smaller than 'k_pu'.
I did some experiments and the bigger 'k_i' slows down a lot the rising temp. That's why this change.
It was OK to have k_i=10 when we were in milliWatts world, when the min power value was bigger, thus 'k_pu' was also bigger than our hard-coded 'k_i'.
> > Depending on the thermal behavior of a board, these coefficients could > be very different, no ? >
Yes, I strongly believe that vendor engineers will make experiments with these values and not go with default. Then they will store the k_pu, k_po, k_i via sysfs interface, with also sustainable_power.
But I have to also fix the hard-coded k_i in the estimation. As described above, when we have small power values from abstract scale, the k_i stays too big.
Regards, Lukasz
| |