lkml.org 
[lkml]   [2020]   [Oct]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v14 15/15] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode
On 01/10/20 08:38AM, Tudor.Ambarus@microchip.com wrote:
> On 9/30/20 9:57 PM, Pratyush Yadav wrote:
> > EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> >
> > Since this flash doesn't have a Profile 1.0 table, the Octal DTR
> > capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
> > fast read settings.
> >
> > Enable Octal DTR mode with 20 dummy cycles to allow running at the
> > maximum supported frequency of 200Mhz.
> >
> > The flash supports the soft reset sequence. So, add the flag in the
> > flash's info.
> >
> > Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> > ---
> > drivers/mtd/spi-nor/micron-st.c | 100 +++++++++++++++++++++++++++++++-
> > 1 file changed, 99 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/mtd/spi-nor/micron-st.c b/drivers/mtd/spi-nor/micron-st.c
> > index ef3695080710..b0002c29fd37 100644
> > --- a/drivers/mtd/spi-nor/micron-st.c
> > +++ b/drivers/mtd/spi-nor/micron-st.c
> > @@ -8,10 +8,108 @@
> >
> > #include "core.h"
> >
> > +#define SPINOR_OP_MT_DTR_RD 0xfd /* Fast Read opcode in DTR mode */
> > +#define SPINOR_OP_MT_RD_ANY_REG 0x85 /* Read volatile register */
> > +#define SPINOR_OP_MT_WR_ANY_REG 0x81 /* Write volatile register */
> > +#define SPINOR_REG_MT_CFR0V 0x00 /* For setting octal DTR mode */
> > +#define SPINOR_REG_MT_CFR1V 0x01 /* For setting dummy cycles */
> > +#define SPINOR_MT_OCT_DTR 0xe7 /* Enable Octal DTR. */
> > +#define SPINOR_MT_EXSPI 0xff /* Enable Extended SPI (default) */
> > +
> > +static int spi_nor_micron_octal_dtr_enable(struct spi_nor *nor, bool enable)
> > +{
> > + struct spi_mem_op op;
> > + u8 *buf = nor->bouncebuf;
> > + int ret;
> > +
> > + if (enable) {
> > + /* Use 20 dummy cycles for memory array reads. */
> > + ret = spi_nor_write_enable(nor);
> > + if (ret)
> > + return ret;
> > +
> > + *buf = 20;
> > + op = (struct spi_mem_op)
> > + SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_MT_WR_ANY_REG, 1),
> > + SPI_MEM_OP_ADDR(3, SPINOR_REG_MT_CFR1V, 1),
> > + SPI_MEM_OP_NO_DUMMY,
> > + SPI_MEM_OP_DATA_OUT(1, buf, 1));
> > +
> > + ret = spi_mem_exec_op(nor->spimem, &op);
> > + if (ret)
> > + return ret;
> > +
> > + ret = spi_nor_wait_till_ready(nor);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + ret = spi_nor_write_enable(nor);
> > + if (ret)
> > + return ret;
> > +
> > + if (enable)
> > + *buf = SPINOR_MT_OCT_DTR;
> > + else
> > + *buf = SPINOR_MT_EXSPI;
> > +
> > + op = (struct spi_mem_op)
> > + SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_MT_WR_ANY_REG, 1),
> > + SPI_MEM_OP_ADDR(enable ? 3 : 4,
> > + SPINOR_REG_MT_CFR0V, 1),
> > + SPI_MEM_OP_NO_DUMMY,
> > + SPI_MEM_OP_DATA_OUT(1, buf, 1));
> > +
> > + if (!enable)
> > + spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
> > +
> > + ret = spi_mem_exec_op(nor->spimem, &op);
> > + if (ret)
> > + return ret;
> > +
> > + /* Give some time for the mode change to take place. */
> > + usleep_range(400, 600);
>
> Don't we need to still read the Status Register here? The same question
> applies for the previous patch.

We do, and I even added a check here after reading your email. But in
practice I realized that all we get from it is a false sense of
security. If the sleep is too little, then the read status register will
give out garbage data (or might even hang the controller) because the
flash is still in a transition state. If the sleep is long enough then
the read status register will tell us the flash is ready on the first
try and we don't really gain any new insight.

> > +
> > + return 0;
> > +}
> > +
> > +static void mt35xu512aba_default_init(struct spi_nor *nor)
> > +{
> > + nor->params->octal_dtr_enable = spi_nor_micron_octal_dtr_enable;
> > +}
> > +
> > +static void mt35xu512aba_post_sfdp_fixup(struct spi_nor *nor)
> > +{
> > + /* Set the Fast Read settings. */
> > + nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
> > + spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
> > + 0, 20, SPINOR_OP_MT_DTR_RD,
> > + SNOR_PROTO_8_8_8_DTR);
> > +
> > + nor->cmd_ext_type = SPI_NOR_EXT_REPEAT;
> > + nor->params->rdsr_dummy = 8;
> > + nor->params->rdsr_addr_nbytes = 0;
> > +
> > + /*
> > + * The BFPT quad enable field is set to a reserved value so the quad
> > + * enable function is ignored by spi_nor_parse_bfpt(). Make sure we
> > + * disable it.
> > + */
> > + nor->params->quad_enable = NULL;
> > +}
> > +
> > +static struct spi_nor_fixups mt35xu512aba_fixups = {
> > + .default_init = mt35xu512aba_default_init,
> > + .post_sfdp = mt35xu512aba_post_sfdp_fixup,
> > +};
> > +
> > static const struct flash_info micron_parts[] = {
> > { "mt35xu512aba", INFO(0x2c5b1a, 0, 128 * 1024, 512,
> > SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
> > - SPI_NOR_4B_OPCODES) },
> > + SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
> > + SPI_NOR_OCTAL_DTR_PP |
> > + SPI_NOR_IO_MODE_EN_VOLATILE)
> > + .fixups = &mt35xu512aba_fixups},
> > { "mt35xu02g", INFO(0x2c5b1c, 0, 128 * 1024, 2048,
> > SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
> > SPI_NOR_4B_OPCODES) },
> > --
> > 2.28.0
> >
>

--
Regards,
Pratyush Yadav
Texas Instruments India

\
 
 \ /
  Last update: 2020-10-01 21:44    [W:0.067 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site