lkml.org 
[lkml]   [2020]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] tty/serial: atmel: RS485 & ISO7816: wait for TXRDY before sending data
Date
On 08.01.2020 15:45, Richard Genoud wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>
> Le 07/01/2020 à 12:17, Codrin.Ciubotariu@microchip.com a écrit :
>> At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
>> modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
>> Register are empty, even though TXRDY might be up and controller is able to
>> receive data. Since the controller sends data only when TXEMPTY is ready,
>> on RS485, when DMA is not used, the RTS pin is driven low after each byte.
>> With this patch, the characters will be transmitted when TXRDY is up and
>> so, RTS pin will remain high between bytes.
>> The performance improvement on RS485 is about 8% with a baudrate of 300.
>>
>> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
> seems ok to me
> Acked-by: Richard Genoud <richard.genoud@gmail.com>
>
> NB: MS exchange has added some =3D and =20 here and there, but git am
> doesn't seems to be bothered by them.

We are struggling with some e-mail changes, sorry for that. Thanks for
letting me know about this.

>> ---
>> drivers/tty/serial/atmel_serial.c | 26 +++++++++++++++++++-------
>> 1 file changed, 19 insertions(+), 7 deletions(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index a8dc8af83f39..19c8fb9faa36 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -313,7 +313,11 @@ static int atmel_config_rs485(struct uart_port *port,
>>
>> if (rs485conf->flags & SER_RS485_ENABLED) {
>> dev_dbg(port->dev, "Setting UART to RS485\n");
>> - atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
>> + if (port->rs485.flags & SER_RS485_RX_DURING_TX)
>> + atmel_port->tx_done_mask = ATMEL_US_TXRDY;
>> + else
>> + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
>> +
>> atmel_uart_writel(port, ATMEL_US_TTGR,
>> rs485conf->delay_rts_after_send);
>> mode |= ATMEL_US_USMODE_RS485;
>> @@ -831,7 +835,7 @@ static void atmel_tx_chars(struct uart_port *port)
>> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>>
>> if (port->x_char &&
>> - (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) {
>> + (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) {
>> atmel_uart_write_char(port, port->x_char);
>> port->icount.tx++;
>> port->x_char = 0;
>> @@ -839,8 +843,7 @@ static void atmel_tx_chars(struct uart_port *port)
>> if (uart_circ_empty(xmit) || uart_tx_stopped(port))
>> return;
>>
>> - while (atmel_uart_readl(port, ATMEL_US_CSR) &
>> - atmel_port->tx_done_mask) {
>> + while (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY) {
>> atmel_uart_write_char(port, xmit->buf[xmit->tail]);
>> xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
>> port->icount.tx++;
>> @@ -851,10 +854,20 @@ static void atmel_tx_chars(struct uart_port *port)
>> if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
>> uart_write_wakeup(port);
>>
>> - if (!uart_circ_empty(xmit))
>> + if (!uart_circ_empty(xmit)) {
>> + /* we still have characters to transmit, so we should continue
>> + * transmitting them when TX is ready, regardless of
>> + * mode or duplexity
>> + */
>> + atmel_port->tx_done_mask |= ATMEL_US_TXRDY;
>> +
>> /* Enable interrupts */
>> atmel_uart_writel(port, ATMEL_US_IER,
>> atmel_port->tx_done_mask);
>> + } else {
>> + if (atmel_uart_is_half_duplex(port))
>> + atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY;
>> + }
>> }
>>
>> static void atmel_complete_tx_dma(void *arg)
>> @@ -2525,8 +2538,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
>> * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
>> * ENDTX|TXBUFE
>> */
>> - if (port->rs485.flags & SER_RS485_ENABLED ||
>> - port->iso7816.flags & SER_ISO7816_ENABLED)
>> + if (atmel_uart_is_half_duplex(port))
>> atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
>> else if (atmel_use_pdc_tx(port)) {
>> port->fifosize = PDC_BUFFER_SIZE;
>>
>
\
 
 \ /
  Last update: 2020-01-08 17:04    [W:0.068 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site