lkml.org 
[lkml]   [2020]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 04/14] phy/rockchip: inno-hdmi: do not power on rk3328 post pll on reg write
Date
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.

Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.

Fixes: 53706a116863 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
drivers/phy/rockchip/phy-rockchip-inno-hdmi.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
index 06db69c8373e..3a59a6da0440 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
@@ -1020,9 +1020,10 @@ inno_hdmi_phy_rk3328_power_on(struct inno_hdmi_phy *inno,

inno_write(inno, 0xac, RK3328_POST_PLL_FB_DIV_7_0(cfg->fbdiv));
if (cfg->postdiv == 1) {
- inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS);
inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
RK3328_POST_PLL_PRE_DIV(cfg->prediv));
+ inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS |
+ RK3328_POST_PLL_POWER_DOWN);
} else {
v = (cfg->postdiv / 2) - 1;
v &= RK3328_POST_PLL_POST_DIV_MASK;
@@ -1030,7 +1031,8 @@ inno_hdmi_phy_rk3328_power_on(struct inno_hdmi_phy *inno,
inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
RK3328_POST_PLL_PRE_DIV(cfg->prediv));
inno_write(inno, 0xaa, RK3328_POST_PLL_POST_DIV_ENABLE |
- RK3328_POST_PLL_REFCLK_SEL_TMDS);
+ RK3328_POST_PLL_REFCLK_SEL_TMDS |
+ RK3328_POST_PLL_POWER_DOWN);
}

for (v = 0; v < 14; v++)
--
2.17.1
\
 
 \ /
  Last update: 2020-01-08 22:08    [W:0.116 / U:1.840 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site