lkml.org 
[lkml]   [2020]   [Jan]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 4.14 02/74] iio: adc: max9611: Fix too short conversion time delay
    Date
    From: Geert Uytterhoeven <geert+renesas@glider.be>

    [ Upstream commit 9fd229c478fbf77c41c8528aa757ef14210365f6 ]

    As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
    reading in probe"), max9611 initialization sometimes fails on the
    Salvator-X(S) development board with:

    max9611 4-007f: Invalid value received from ADC 0x8000: aborting
    max9611: probe of 4-007f failed with error -5

    The max9611 driver tests communications with the chip by reading the die
    temperature during the probe function, which returns an invalid value.

    According to the datasheet, the typical ADC conversion time is 2 ms, but
    no minimum or maximum values are provided. Maxim Technical Support
    confirmed this was tested with temperature Ta=25 degreeC, and promised
    to inform me if a maximum/minimum value is available (they didn't get
    back to me, so I assume it is not).

    However, the driver assumes a 1 ms conversion time. Usually the
    usleep_range() call returns after more than 1.8 ms, hence it succeeds.
    When it returns earlier, the data register may be read too early, and
    the previous measurement value will be returned. After boot, this is
    the temperature POR (power-on reset) value, causing the failure above.

    Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.

    Note that this issue has always been present, but it was exposed by the
    aformentioned commit.

    Fixes: 69780a3bbc0b1e7e ("iio: adc: Add Maxim max9611 ADC driver")
    Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
    Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
    Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
    Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
    Signed-off-by: Sasha Levin <sashal@kernel.org>
    ---
    drivers/iio/adc/max9611.c | 16 ++++++++++------
    1 file changed, 10 insertions(+), 6 deletions(-)

    diff --git a/drivers/iio/adc/max9611.c b/drivers/iio/adc/max9611.c
    index 33be07c78b96..8649a61c50bc 100644
    --- a/drivers/iio/adc/max9611.c
    +++ b/drivers/iio/adc/max9611.c
    @@ -92,6 +92,12 @@
    #define MAX9611_TEMP_SCALE_NUM 1000000
    #define MAX9611_TEMP_SCALE_DIV 2083

    +/*
    + * Conversion time is 2 ms (typically) at Ta=25 degreeC
    + * No maximum value is known, so play it safe.
    + */
    +#define MAX9611_CONV_TIME_US_RANGE 3000, 3300
    +
    struct max9611_dev {
    struct device *dev;
    struct i2c_client *i2c_client;
    @@ -239,11 +245,9 @@ static int max9611_read_single(struct max9611_dev *max9611,
    return ret;
    }

    - /*
    - * need a delay here to make register configuration
    - * stabilize. 1 msec at least, from empirical testing.
    - */
    - usleep_range(1000, 2000);
    + /* need a delay here to make register configuration stabilize. */
    +
    + usleep_range(MAX9611_CONV_TIME_US_RANGE);

    ret = i2c_smbus_read_word_swapped(max9611->i2c_client, reg_addr);
    if (ret < 0) {
    @@ -511,7 +515,7 @@ static int max9611_init(struct max9611_dev *max9611)
    MAX9611_REG_CTRL2, 0);
    return ret;
    }
    - usleep_range(1000, 2000);
    + usleep_range(MAX9611_CONV_TIME_US_RANGE);

    return 0;
    }
    --
    2.20.1


    \
     
     \ /
      Last update: 2020-01-07 22:17    [W:4.099 / U:0.432 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site