lkml.org 
[lkml]   [2020]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v2 4/6] Documentation: arm64: document support for the AMU extension
From
Date
On 18/12/2019 18:26, Ionela Voinescu wrote:
> +Basic support
> +-------------
> +
> +The kernel can safely run a mix of CPUs with and without support for the
> +activity monitors extension. Therefore, when CONFIG_ARM64_AMU_EXTN is
> +selected we unconditionally enable the capability to allow any late CPU
> +(secondary or hotplugged) to detect and use the feature.
> +
> +When the feature is detected on a CPU, a per-CPU variable (amu_feat) is
> +set, but this does not guarantee the correct functionality of the
> +counters, only the presence of the extension.
> +
> +Firmware (code running at higher exception levels, e.g. arm-tf) support is
> +needed to:
> + - Enable access for lower exception levels (EL2 and EL1) to the AMU
> + registers.
> + - Enable the counters. If not enabled these will read as 0.

Just to make sure I understand - if AMUs are physically present but not
enabled by FW, we'll still
- see them as implemented in ID_AA64PFR0_EL1.AMU
- see some counters as available with e.g. AMCGCR_ELO.CG0NC > 0

But reading some AMEVCNTR<g><n> will return 0?

> + - Save/restore the counters before/after the CPU is being put/brought up
> + from the 'off' power state.
> +
> +When using kernels that have this configuration enabled but boot with
> +broken firmware the user may experience panics or lockups when accessing
> +the counter registers.

Yikes

> Even if these symptoms are not observed, the
> +values returned by the register reads might not correctly reflect reality.
> +Most commonly, the counters will read as 0, indicating that they are not
> +enabled. If proper support is not provided in firmware it's best to disable
> +CONFIG_ARM64_AMU_EXTN.
> +

I haven't seen something that would try to catch this on the kernel side.
Can we try to detect that (e.g. at least one counter returns > 0) in
cpu_amu_enable() and thus not write to the CPU-local 'amu_feat'?

While we're on the topic of detecting broken stuff, what if some CPUs
implement some auxiliary counters that some others don't?

> +The fixed counters of AMUv1 are accessible though the following system
> +register definitions:
> + - SYS_AMEVCNTR0_CORE_EL0
> + - SYS_AMEVCNTR0_CONST_EL0
> + - SYS_AMEVCNTR0_INST_RET_EL0
> + - SYS_AMEVCNTR0_MEM_STALL_EL0
> +
> +Auxiliary platform specific counters can be accessed using
> +SYS_AMEVCNTR1_EL0(n), where n is a value between 0 and 15.
> +
> +Details can be found in: arch/arm64/include/asm/sysreg.h.
> +
> diff --git a/Documentation/arm64/booting.rst b/Documentation/arm64/booting.rst
> index 5d78a6f5b0ae..a3f1a47b6f1c 100644
> --- a/Documentation/arm64/booting.rst
> +++ b/Documentation/arm64/booting.rst
> @@ -248,6 +248,20 @@ Before jumping into the kernel, the following conditions must be met:
> - HCR_EL2.APK (bit 40) must be initialised to 0b1
> - HCR_EL2.API (bit 41) must be initialised to 0b1
>
> + For CPUs with Activity Monitors Unit v1 (AMUv1) extension present:
> + - If EL3 is present:
> + CPTR_EL3.TAM (bit 30) must be initialised to 0b0
> + CPTR_EL2.TAM (bit 30) must be initialised to 0b0
> + AMCNTENSET0_EL0 must be initialised to 0b1111

Nit: Or be a superset of the above, right? AIUI v1 only mandates the lower
4 bits to be set. Probably doesn't matter that much...

\
 
 \ /
  Last update: 2020-01-27 17:48    [W:0.186 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site