lkml.org 
[lkml]   [2020]   [Jan]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net v2 11/12] net/sonic: Fix CAM initialization
Date
Section 4.3.1 of the datasheet says,

This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.

Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.

After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.

When in reset mode, take the opportunity to reset the CAM Enable
register.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
drivers/net/ethernet/natsemi/sonic.c | 21 ++++++++++++---------
1 file changed, 12 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/natsemi/sonic.c b/drivers/net/ethernet/natsemi/sonic.c
index 55660acf5ccc..b712cc6a2560 100644
--- a/drivers/net/ethernet/natsemi/sonic.c
+++ b/drivers/net/ethernet/natsemi/sonic.c
@@ -634,6 +634,8 @@ static void sonic_multicast_list(struct net_device *dev)
(netdev_mc_count(dev) > 15)) {
rcr |= SONIC_RCR_AMC;
} else {
+ unsigned long flags;
+
netif_dbg(lp, ifup, dev, "%s: mc_count %d\n", __func__,
netdev_mc_count(dev));
sonic_set_cam_enable(dev, 1); /* always enable our own address */
@@ -647,9 +649,14 @@ static void sonic_multicast_list(struct net_device *dev)
i++;
}
SONIC_WRITE(SONIC_CDC, 16);
- /* issue Load CAM command */
SONIC_WRITE(SONIC_CDP, lp->cda_laddr & 0xffff);
+
+ /* LCAM and TXP commands can't be used simultaneously */
+ local_irq_save(flags);
+ sonic_quiesce(dev, SONIC_CR_TXP);
SONIC_WRITE(SONIC_CMD, SONIC_CR_LCAM);
+ sonic_quiesce(dev, SONIC_CR_LCAM);
+ local_irq_restore(flags);
}
}

@@ -675,6 +682,9 @@ static int sonic_init(struct net_device *dev)
SONIC_WRITE(SONIC_ISR, 0x7fff);
SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);

+ /* While in reset mode, clear CAM Enable register */
+ SONIC_WRITE(SONIC_CE, 0);
+
/*
* clear software reset flag, disable receiver, clear and
* enable interrupts, then completely initialize the SONIC
@@ -785,14 +795,7 @@ static int sonic_init(struct net_device *dev)
* load the CAM
*/
SONIC_WRITE(SONIC_CMD, SONIC_CR_LCAM);
-
- i = 0;
- while (i++ < 100) {
- if (SONIC_READ(SONIC_ISR) & SONIC_INT_LCD)
- break;
- }
- netif_dbg(lp, ifup, dev, "%s: CMD=%x, ISR=%x, i=%d\n", __func__,
- SONIC_READ(SONIC_CMD), SONIC_READ(SONIC_ISR), i);
+ sonic_quiesce(dev, SONIC_CR_LCAM);

/*
* enable receiver, disable loopback
--
2.24.1
\
 
 \ /
  Last update: 2020-01-21 23:11    [W:0.450 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site