lkml.org 
[lkml]   [2020]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] MIPS: Ingenic: Add missing nodes for X1000 and CU1000-Neo.
Date
Add I2C0/I2C1/I2C2 nodes for X1000 and add I2C0, ADS7830,
MSC1, AP6212A, wlan_pwrseq nodes for CU1000-Neo.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
arch/mips/boot/dts/ingenic/cu1000-neo.dts | 71 +++++++++++++++++++++++++++++++
arch/mips/boot/dts/ingenic/x1000.dtsi | 45 ++++++++++++++++++++
2 files changed, 116 insertions(+)

diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index b0733da..03abd94 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -4,6 +4,7 @@
#include "x1000.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>

/ {
compatible = "yna,cu1000-neo", "ingenic,x1000";
@@ -21,6 +22,22 @@
device_type = "memory";
reg = <0x0 0x04000000>;
};
+
+ wlan_pwrseq: msc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+
+ clocks = <&lpoclk>;
+ clock-names = "ext_clock";
+
+ reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+
+ lpoclk: ap6212a {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
};

&exclk {
@@ -36,6 +53,20 @@
ingenic,pwm-channels-mask = <0xfa>;
};

+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_i2c0>;
+
+ ads7830@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pins_uart2>;
@@ -78,7 +109,41 @@
status = "okay";
};

+&msc1 {
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ non-removable;
+
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ status = "okay";
+
+ ap6212a: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpc>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ brcm,drive-strength = <10>;
+ };
+};
+
&pinctrl {
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-disable;
+ };
+
pins_uart2: uart2 {
function = "uart2";
groups = "uart2-data-d";
@@ -96,4 +161,10 @@
groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
bias-disable;
};
+
+ pins_msc1: msc1 {
+ function = "mmc1";
+ groups = "mmc1-1bit", "mmc1-4bit";
+ bias-disable;
+ };
};
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index ea54263..376df1b 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -169,6 +169,51 @@
};
};

+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <60>;
+
+ clocks = <&cgu X1000_CLK_I2C0>;
+
+ status = "disabled";
+ };
+
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <59>;
+
+ clocks = <&cgu X1000_CLK_I2C1>;
+
+ status = "disabled";
+ };
+
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1000_CLK_I2C2>;
+
+ status = "disabled";
+ };
+
uart0: serial@10030000 {
compatible = "ingenic,x1000-uart";
reg = <0x10030000 0x100>;
--
2.7.4
\
 
 \ /
  Last update: 2020-01-14 18:05    [W:0.039 / U:134.516 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site