lkml.org 
[lkml]   [2020]   [Jan]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] hwmon: Driver for temperature sensors on SATA drives
Am So., 12. Jan. 2020 um 14:07 Uhr schrieb Guenter Roeck <linux@roeck-us.net>:
>
> On 1/12/20 4:07 AM, Linus Walleij wrote:
> > On Sun, Jan 12, 2020 at 1:03 PM Gabriel C <nix.or.die@gmail.com> wrote:
> >> Am So., 12. Jan. 2020 um 12:22 Uhr schrieb Linus Walleij
> >> <linus.walleij@linaro.org>:
> >>>
> >>> On Sun, Jan 12, 2020 at 12:18 PM Gabriel C <nix.or.die@gmail.com> wrote:
> >>>
> >>>> What I've noticed however is the nvme temperature low/high values on
> >>>> the Sensors X are strange here.
> >>> (...)
> >>>> Sensor 1: +27.9°C (low = -273.1°C, high = +65261.8°C)
> >>>> Sensor 2: +29.9°C (low = -273.1°C, high = +65261.8°C)
> >>> (...)
> >>>> Sensor 1: +23.9°C (low = -273.1°C, high = +65261.8°C)
> >>>> Sensor 2: +25.9°C (low = -273.1°C, high = +65261.8°C)
> >>>
> >>> That doesn't look strange to me. It seems like reasonable defaults
> >>> from the firmware if either it doesn't really log the min/max temperatures
> >>> or hasn't been through a cycle of updating these yet. Just set both
> >>> to absolute min/max temperatures possible.
> >>
> >> Ok I'll check that.
> >>
> >> Do you mean by setting the temperatures to use a lmsensors config?
> >> Or is there a way to set these with a nvme command?
> >
> > Not that I know of.
> >
> > The min/max are the minumum and maximum temperatures the
> > device has experienced during this power-on cycle.
> >
>
> No, that would be lowest/highest. The above are (or should be) per-sensor
> setpoints. The default for those is typically the absolute minimum /
> maximum of the supported range.
>
> Some SATA drives report the lowest/highest temperatures experienced
> since power cycle, like here.
>
> drivetemp-scsi-5-0
> Adapter: SCSI adapter
> temp1: +23.0°C (low = +0.0°C, high = +60.0°C)
> (crit low = -41.0°C, crit = +85.0°C)
> (lowest = +20.0°C, highest = +31.0°C)
>

The SATA temperatures are fine and reported like this here too, just
the nvme ones are strange.

drivetemp-scsi-4-0
Adapter: SCSI adapter
temp1: +28.0°C (low = +1.0°C, high = +61.0°C)
(crit low = +2.0°C, crit = +60.0°C)
(lowest = +16.0°C, highest = +31.0°C)

drivetemp-scsi-12-0
Adapter: SCSI adapter
temp1: +29.0°C (low = +1.0°C, high = +61.0°C)
(crit low = +2.0°C, crit = +60.0°C)
(lowest = +18.0°C, highest = +32.0°C)

and so on.

Btw, where I can find the code does these calculations?

Best regards,

Gabriel C.

\
 
 \ /
  Last update: 2020-01-12 14:46    [W:0.077 / U:13.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site