lkml.org 
[lkml]   [2020]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab
Hi,

On Fri, Jan 10, 2020 at 11:52:25PM +0800, Icenowy Zheng wrote:
> PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
>
> It includes the following peripherals:
>
> USB:
> - A microUSB Type-B port connected to the OTG-capable USB PHY of
> Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
> Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
> functionality on this port.
> - A USB Type-A port is connected to the internal hub attached to the
> non-OTG USB PHY of Allwinner A64.
> - There are reserved pins for an external keyboard connected to the
> internal hub.
>
> Power:
> - The microUSB port has its Vbus connected to AXP803, mentioned above.
> - A DC jack (of a strange size, 2.5mm outer diameter) is connected to
> the ACIN of AXP803.
> - A Li-Polymer battery is connected to the battery pins of AXP803.
>
> Storage:
> - An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
> module by factory.
> - An external microSD slot is hidden under a protect case.
>
> Display:
> - A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
> - A mini HDMI port.
>
> Input:
> - A touch panel attached to a Goodix GT9271 touch controller.
> - Volume keys connected to the LRADC of the A64 SoC.
>
> Camera:
> - An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
> - A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
>
> Audio:
> - A headphone jack is conencted to the SoC's internal codec.
> - A speaker connected is to the Line Out port of SoC's internal codec, via
> an amplifier.
>
> Misc:
> - Debug UART is muxed with the headphone jack, with the switch next to
> the microSD slot.
> - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
> - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
> one in Pinebook.
>
> This commit adds a basically usable device tree for it, implementing
> most of the features mentioned above. HDMI is not supported now because
> bad LCD-HDMI coexistence situation of mainline A64 display driver, and
> the front camera currently lacks a driver and a facility to share the
> bus with the rear one.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
> 2 files changed, 462 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index cf4f78617c3f..6dad63881cd3 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> new file mode 100644
> index 000000000000..1dfa3668636e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> @@ -0,0 +1,461 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-a64.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "PineTab";
> + compatible = "pine64,pinetab", "allwinner,sun50i-a64";
> +
> + aliases {
> + serial0 = &uart0;
> + ethernet0 = &rtl8723cs;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;

Each step should be a perceived step, not a decimal one. So let's say,
if you have 10 steps, each step should be seen as a 10% increase in
brightness. Usually a quadratic increase works better there.

> +&dsi {
> + vcc-dsi-supply = <&reg_dldo1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";

address-cells and size-cells aren't in the DTSI? They should be.

> +
> + panel@0 {
> + compatible = "feixin,k101-im2ba02";
> + reg = <0>;
> + avdd-supply = <&reg_dc1sw>;
> + dvdd-supply = <&reg_dc1sw>;
> + cvdd-supply = <&reg_ldo_io1>;
> + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> + backlight = <&backlight>;
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;

That should be set in the DTSI already?

> + status = "okay";
> +
> + touchscreen@5d {
> + compatible = "goodix,gt9271";
> + reg = <0x5d>;
> + interrupt-parent = <&pio>;
> + interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
> + irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> + reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> + AVDD28-supply = <&reg_ldo_io1>;
> + };
> +};
> +
> +&i2c0_pins {
> + bias-pull-up;
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;

Ditto

> + status = "okay";
> +
> + bma223@18 {
> + compatible = "bosch,bma223", "bosch,bma222e";
> + reg = <0x18>;
> + interrupt-parent = <&pio>;
> + interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
> + mount-matrix = "0", "-1", "0",
> + "-1", "0", "0",
> + "0", "0", "-1";
> + };
> +};
> +
> +&lradc {
> + vref-supply = <&reg_aldo3>;
> + status = "okay";
> +
> + button-200 {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + channel = <0>;
> + voltage = <200000>;
> + };
> +
> + button-400 {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + channel = <0>;
> + voltage = <400000>;
> + };
> +};
> +
> +&mixer1 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;

Ditto

> + vmmc-supply = <&reg_dcdc1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;

Ditto

> + vmmc-supply = <&reg_dldo4>;
> + vqmmc-supply = <&reg_eldo1>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +
> + rtl8723cs: wifi@1 {
> + reg = <1>;
> + };
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_pins>;

Ditto

Looks good otherwise, thanks!
Maxime
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-01-10 18:23    [W:0.155 / U:1.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site