lkml.org 
[lkml]   [2019]   [Sep]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] net/skbuff: silence warnings under memory pressure
From
Date
On Wed, 2019-09-04 at 14:07 +0200, Michal Hocko wrote:
> On Wed 04-09-19 07:59:17, Qian Cai wrote:
> > On Wed, 2019-09-04 at 10:25 +0200, Michal Hocko wrote:
> > > On Wed 04-09-19 16:00:42, Sergey Senozhatsky wrote:
> > > > On (09/04/19 15:41), Sergey Senozhatsky wrote:
> > > > > But the thing is different in case of dump_stack() + show_mem() +
> > > > > some other output. Because now we ratelimit not a single printk()
> > > > > line,
> > > > > but hundreds of them. The ratelimit becomes - 10 * $$$ lines in 5
> > > > > seconds
> > > > > (IOW, now we talk about thousands of lines).
> > > >
> > > > And on devices with slow serial consoles this can be somewhat close to
> > > > "no ratelimit". *Suppose* that warn_alloc() adds 700 lines each time.
> > > > Within 5 seconds we can call warn_alloc() 10 times, which will add 7000
> > > > lines to the logbuf. If printk() can evict only 6000 lines in 5 seconds
> > > > then we have a growing number of pending logbuf messages.
> > >
> > > Yes, ratelimit is problematic when the ratelimited operation is slow. I
> > > guess that is a well known problem and we would need to rework both the
> > > api and the implementation to make it work in those cases as well.
> > > Essentially we need to make the ratelimit act as a gatekeeper to an
> > > operation section - something like a critical section except you can
> > > tolerate more code executions but not too many. So effectively
> > >
> > > start_throttle(rate, number);
> > > /* here goes your operation */
> > > end_throttle();
> > >
> > > one operation is not considered done until the whole section ends.
> > > Or something along those lines.
> > >
> > > In this particular case we can increase the rate limit parameters of
> > > course but I think that longterm we need a better api.
> >
> > The problem is when a system is under heavy memory pressure, everything is
> > becoming slower, so I don't know how to come up with a sane default for rate
> > limit parameters as a generic solution that would work for every machine out
> > there. Sure, it is possible to set a limit as low as possible that would
> > work
> > for the majority of systems apart from people may complain that they are now
> > missing important warnings, but using __GFP_NOWARN in this code would work
> > for
> > all systems. You could even argument there is even a separate benefit that
> > it
> > could reduce the noise-level overall from those build_skb() allocation
> > failures
> > as it has a fall-back mechanism anyway.
>
> As Vlastimil already pointed out, __GFP_NOWARN would hide that reserves
> might be configured too low.

Tune "min_free_kbytes" is also an unreliable solution and situational as the
same reason mentioned previously. It may also need a lot of testing to find out
the right value of it on one particular system.

"
When there is a heavy memory pressure, the system is trying hard to reclaim
memory to fill up the watermark. However, the IO is slow to page out, but the
memory pressure keep draining atomic reservoir, and some of those skb_build()
will fail eventually.

Only if there is a fast IO, it will finish swapping sooner and then invoke the
OOM to end the memory pressure.
"

It also have a drawback that "waste" precious memory resources, as allocations
other than GPF_ATOMIC are unable to use those reserved memory anymore.

\
 
 \ /
  Last update: 2019-09-04 14:29    [W:0.299 / U:0.812 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site