lkml.org 
[lkml]   [2019]   [Sep]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: Is: Default governor regardless of cpuidle driver Was: [PATCH v2] cpuidle-haltpoll: vcpu hotplug support
From
Date
On 9/2/19 10:55 PM, Rafael J. Wysocki wrote:
> On Thu, Aug 29, 2019 at 7:24 PM Marcelo Tosatti <mtosatti@redhat.com> wrote:
>>
>> On Thu, Aug 29, 2019 at 06:16:05PM +0100, Joao Martins wrote:
>>> On 8/29/19 4:10 PM, Joao Martins wrote:
>>>> When cpus != maxcpus cpuidle-haltpoll will fail to register all vcpus
>>>> past the online ones and thus fail to register the idle driver.
>>>> This is because cpuidle_add_sysfs() will return with -ENODEV as a
>>>> consequence from get_cpu_device() return no device for a non-existing
>>>> CPU.
>>>>
>>>> Instead switch to cpuidle_register_driver() and manually register each
>>>> of the present cpus through cpuhp_setup_state() callback and future
>>>> ones that get onlined. This mimmics similar logic that intel_idle does.
>>>>
>>>> Fixes: fa86ee90eb11 ("add cpuidle-haltpoll driver")
>>>> Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
>>>> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
>>>> ---
>>>
>>> While testing the above, I found out another issue on the haltpoll series.
>>> But I am not sure what is best suited to cpuidle framework, hence requesting
>>> some advise if below is a reasonable solution or something else is preferred.
>>>
>>> Essentially after haltpoll governor got introduced and regardless of the cpuidle
>>> driver the default governor is gonna be haltpoll for a guest (given haltpoll
>>> governor doesn't get registered for baremetal).
>>
>> Right.
>>
>>> Right now, for a KVM guest, the
>>> idle governors have these ratings:
>>>
>>> * ladder -> 10
>>> * teo -> 19
>>> * menu -> 20
>>> * haltpoll -> 21
>>> * ladder + nohz=off -> 25
>>
>> Yes. PowerPC KVM guests crash currently due to the use of the haltpoll
>> governor (have a patch in my queue to fix this, but your solution
>> embraces more cases).
>>
>>> When a guest is booted with MWAIT and intel_idle is probed and sucessfully
>>> registered, we will end up with a haltpoll governor being used as opposed to
>>> 'menu' (which used to be the default case). This would prevent IIUC that other
>>> C-states get used other than poll_state (state 0) and state 1.
>>>
>>> Given that haltpoll governor is largely only useful with a cpuidle-haltpoll
>>> it doesn't look reasonable to be the default? What about using haltpoll governor
>>> as default when haltpoll idle driver registers or modloads.
>>>
>>> My idea to achieve the above would be to decrease the rating to 9 (before the
>>> lowest rated governor) and retain old defaults before haltpoll. Then we would
>>> allow a cpuidle driver to define a preferred governor to switch on idle driver
>>> registration. Naturally all of would be ignored if overidden by
>>> cpuidle.governor=.
>>>
>>> The diff below the scissors line is an example of that.
>>>
>>> Thoughts?
>>
>> Works for me. Rafael?
>
> It works for me too, basically, except that I would rename
> cpuidle_default_governor in the patch to cpuidle_prev_governor.
>

Great! I'll send over a series with this then (splitted accordingly).

Also, In the course of hotplug/hotunplug testing, I found two small issues with
modload/modunload -- regardless of the hotplug patch. So I am gonna add that to
the series too.

Joao

\
 
 \ /
  Last update: 2019-09-03 12:16    [W:0.075 / U:3.624 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site