lkml.org 
[lkml]   [2019]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] clk: meson: a1: add support for Amlogic A1 clock driver
From
Date
Hi, Jerome

Thank you for review.

On 2019/9/25 23:09, Jerome Brunet wrote:
> On Wed 25 Sep 2019 at 19:44, Jian Hu <jian.hu@amlogic.com> wrote:
>
>> The Amlogic A1 clock includes three parts:
>> peripheral clocks, pll clocks, CPU clocks.
>> sys pll and CPU clocks will be sent in next patch.
>>
>> Unlike the previous series, there is no EE/AO domain
>> in A1 CLK controllers.
>>
>> Signed-off-by: Jian Hu <jian.hu@amlogic.com>
>> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
>> ---
>> arch/arm64/Kconfig.platforms | 1 +
>> drivers/clk/meson/Kconfig | 10 +
>> drivers/clk/meson/Makefile | 1 +
>> drivers/clk/meson/a1.c | 2617 ++++++++++++++++++++++++++++++++++++++++++
>> drivers/clk/meson/a1.h | 172 +++
>> 5 files changed, 2801 insertions(+)
>> create mode 100644 drivers/clk/meson/a1.c
>> create mode 100644 drivers/clk/meson/a1.h
>>
>> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
>> index 16d7614..a48f67d 100644
>> --- a/arch/arm64/Kconfig.platforms
>> +++ b/arch/arm64/Kconfig.platforms
>> @@ -138,6 +138,7 @@ config ARCH_MESON
>> select COMMON_CLK_AXG
>> select COMMON_CLK_G12A
>> select MESON_IRQ_GPIO
>> + select COMMON_CLK_A1
>
> This need to be separate patch addressed to Kevin once your driver is merged
>
ok, I will remove it in PATCH V2. And send it again after the driver is
merged.
>> help
>> This enables support for the arm64 based Amlogic SoCs
>> such as the s905, S905X/D, S912, A113X/D or S905X/D2
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index dabeb43..e6cb4c3 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -107,3 +107,13 @@ config COMMON_CLK_G12A
>> help
>> Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>> devices, aka g12a. Say Y if you want peripherals to work.
>> +
>> +config COMMON_CLK_A1
>> + bool
>> + depends on ARCH_MESON
>> + select COMMON_CLK_MESON_REGMAP
>> + select COMMON_CLK_MESON_DUALDIV
>> + select COMMON_CLK_MESON_PLL
>> + help
>> + Support for the clock controller on Amlogic A113L device,
>> + aka a1. Say Y if you want peripherals to work.
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 3939f21..6be3a8f 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -19,3 +19,4 @@ obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> +obj-$(CONFIG_COMMON_CLK_A1) += a1.o
>> diff --git a/drivers/clk/meson/a1.c b/drivers/clk/meson/a1.c
>> new file mode 100644
>> index 0000000..26edae0f
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1.c
>> @@ -0,0 +1,2617 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/init.h>
>> +#include <linux/of_device.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of_address.h>
>> +#include "clk-mpll.h"
>> +#include "clk-pll.h"
>> +#include "clk-regmap.h"
>> +#include "vid-pll-div.h"
>> +#include "clk-dualdiv.h"
>> +#include "meson-eeclk.h"
>> +#include "a1.h"
>> +
>> +/* PLLs clock in gates, its parent is xtal */
>> +static struct clk_regmap a1_xtal_clktree = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 0,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_clktree",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>
> Is CCF even expected to touch this ever ? what about RO ops ?
> Please review your other clocks with this in mind
>
the clock should not be changed at runtime.clk_regmap_gate_ro_ops
is a good idea. Set RO ops and remove the CLK_IS_CRITICAL flag.
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_xtal_fixpll = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 1,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_fixpll",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_xtal_usb_phy = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 2,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_usb_phy",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>
> How is an USB clock critical to the system ?
> Please review your other clocks with comment in mind ...
the usb clock does not affect the system,
remove the CLK_IS_CRITICAL flag
>
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_xtal_usb_ctrl = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 3,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_usb_ctrl",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
the usb clock does not affect the system,
remove the CLK_IS_CRITICAL flag
>> +
>> +static struct clk_regmap a1_xtal_hifipll = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 4,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_hifipll",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
CLK_IS_CRITICAL is need to lock hifi pll.
>> +
>> +static struct clk_regmap a1_xtal_syspll = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 5,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_syspll",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
when CPU clock is at fixed clock, sys pll
will be disabled, xtal_syspll will be disabled too.
when setting sys pll, call clk_set_rate to lock
sys pll, add RO ops to avoid disabling the clock

>> +static struct clk_regmap a1_xtal_dds = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_OSCIN_CTRL,
>> + .bit_idx = 6,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "xtal_dds",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
CLK_IS_CRITICAL is need to lock dds
>> +
>> +/* fixed pll = 1536M
>> + *
>> + * fixed pll ----- fclk_div2 = 768M
>> + * |
>> + * ----- fclk_div3 = 512M
>> + * |
>> + * ----- fclk_div5 = 307.2M
>> + * |
>> + * ----- fclk_div7 = 219.4M
>> + */
>
> The framework will make those calculation ... you can remove this
>
ok, I will remote the comment.
>> +static struct clk_regmap a1_fixed_pll_dco = {
>> + .data = &(struct meson_clk_pll_data){
>> + .en = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL1,
>> + .shift = 0,
>> + .width = 19,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .rst = {
>> + .reg_off = ANACTRL_FIXPLL_CTRL0,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fixed_pll_dco",
>> + .ops = &meson_clk_pll_ro_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_xtal_fixpll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fixed_pll = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 20,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "fixed_pll",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll_dco.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static const struct pll_params_table a1_hifi_pll_params_table[] = {
>> + PLL_PARAMS(128, 5), /* DCO = 614.4M */
>> +};
>> +
>> +static const struct reg_sequence a1_hifi_init_regs[] = {
>> + { .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x10022200 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00301000 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f19480 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x11f19480, .delay_us = 10 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x15f11480, .delay_us = 40 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001140 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>> +};
>> +
>> +/*
>> + * The Meson A1 HIFI PLL is 614.4M, it requires
>> + * a strict register sequence to enable the PLL.
>> + * set meson_clk_pcie_pll_ops as its ops
>> + */
>
> Could you elaborate on this ? What need to be done to enable the clock ?
> Also the HIFI PLL used to be able to do a *LOT* of different rate which
> might be desirable for audio use case. Why is this one restricted to one
> particular rate ?
>
The audio working frequency are 44.1khz, 48khz and 192khz.

614.4M can meet the three frequency.

after the hifi pll, there are two dividers in Audio clock.

614.4M/3200 = 192khz

614.4M/12800 = 48khz

614,4M/13932 = 44.0999khz

>> +static struct clk_regmap a1_hifi_pll = {
>> + .data = &(struct meson_clk_pll_data){
>> + .en = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL1,
>> + .shift = 0,
>> + .width = 19,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_HIFIPLL_STS,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .table = a1_hifi_pll_params_table,
>> + .init_regs = a1_hifi_init_regs,
>> + .init_count = ARRAY_SIZE(a1_hifi_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "hifi_pll",
>> + .ops = &meson_clk_pcie_pll_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_xtal_hifipll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div2_div = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div2 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 21,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div2_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
>> + * or its children clocks.
>> + */
>
> The meaning of this flag is already documented in clk-provider.h
> The reason why you need this flag is lot more interesting here ...
>
> Same below
ok, I will replace new comments here.
>
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div3_div = {
>> + .mult = 1,
>> + .div = 3,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div3_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div3 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 22,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div3",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div3_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
>> + * its children clocks.
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div5_div = {
>> + .mult = 1,
>> + .div = 5,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div5_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div5 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 23,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div5",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div5_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
>> + * its children clocks.
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_fclk_div7_div = {
>> + .mult = 1,
>> + .div = 7,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div7_div",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fixed_pll.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div7 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_FIXPLL_CTRL0,
>> + .bit_idx = 23,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div7",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div7_div.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
>> + * or its children clock.
>> + */
>> + .flags = CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +/* sys clk = 64M */
>
> Again this comment does not help understanding the driver code, please
> remove
>
got it.
>> +static u32 mux_table_sys_ab_clk[] = { 0, 1, 2, 3};
>
> This table is useless
>
>> +static const struct clk_parent_data sys_ab_clk_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_fclk_div2.hw },
>> + { .hw = &a1_fclk_div3.hw },
>> + { .hw = &a1_fclk_div5.hw },
>> +};
>> +
>> +static struct clk_regmap a1_sys_b_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 26,
>> + .table = mux_table_sys_ab_clk,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "sys_b_sel",
>> + .ops = &clk_regmap_mux_ro_ops,
>> + .parent_data = sys_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(sys_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_b_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .shift = 16,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "sys_b_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_sys_b_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_b = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .bit_idx = 29,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "sys_b",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_sys_b_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
>
> Why does this need to be critical ?
> The a1_sys_clk (leaf of the block) could possibly be critical (if you
> explain why) ... but the flag should not be needed in the middle of the
> block
>
ok, the a1_sys_clk should not be changed at runtime, it is the same with
the clk81 clock in G12A. Just use another name in A1.
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_a_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 10,
>> + .table = mux_table_sys_ab_clk,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "sys_a_sel",
>> + .ops = &clk_regmap_mux_ro_ops,
>> + .parent_data = sys_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(sys_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_a_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .shift = 0,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "sys_a_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_sys_a_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_a = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .bit_idx = 13,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "sys_a",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_sys_a_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_sys_clk = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = SYS_CLK_CTRL0,
>> + .mask = 0x1,
>> + .shift = 31,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "sys_clk",
>> + .ops = &clk_regmap_mux_ro_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_sys_a.hw, &a1_sys_b.hw,
>> + },
>> + .num_parents = 2,
>
> SET_RATE_PARENT ?
>
the ops is RO, Maybe no flag is better.
>> + },
>> +};
>> +
>> +/* rtc 32k clock in */
>> +static struct clk_regmap a1_rtc_32k_clkin = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = RTC_BY_OSCIN_CTRL0,
>> + .bit_idx = 31,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "rtc_32k_clkin",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static const struct meson_clk_dualdiv_param a1_32k_div_table[] = {
>> + {
>> + .dual = 1,
>> + .n1 = 733,
>> + .m1 = 8,
>> + .n2 = 732,
>> + .m2 = 11,
>> + }, {}
>> +};
>> +
>> +static struct clk_regmap a1_rtc_32k_div = {
>> + .data = &(struct meson_clk_dualdiv_data){
>> + .n1 = {
>> + .reg_off = RTC_BY_OSCIN_CTRL0,
>> + .shift = 0,
>> + .width = 12,
>> + },
>> + .n2 = {
>> + .reg_off = RTC_BY_OSCIN_CTRL0,
>> + .shift = 12,
>> + .width = 12,
>> + },
>> + .m1 = {
>> + .reg_off = RTC_BY_OSCIN_CTRL1,
>> + .shift = 0,
>> + .width = 12,
>> + },
>> + .m2 = {
>> + .reg_off = RTC_BY_OSCIN_CTRL1,
>> + .shift = 12,
>> + .width = 12,
>> + },
>> + .dual = {
>> + .reg_off = RTC_BY_OSCIN_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .table = a1_32k_div_table,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "rtc_32k_div",
>> + .ops = &meson_clk_dualdiv_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_rtc_32k_clkin.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_rtc_32k_xtal = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = RTC_BY_OSCIN_CTRL1,
>> + .bit_idx = 24,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "rtc_32k_xtal",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_rtc_32k_clkin.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static u32 rtc_32k_sel[] = { 0, 1 };
>
> useless
>
ok, I will delete the table.
>> +
>> +static struct clk_regmap a1_rtc_32k_sel = {
>> + .data = &(struct clk_regmap_mux_data) {
>> + .offset = RTC_CTRL,
>> + .mask = 0x3,
>> + .shift = 0,
>> + .table = rtc_32k_sel,
>> + .flags = CLK_MUX_ROUND_CLOSEST,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "rtc_32k_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_rtc_32k_xtal.hw,
>> + &a1_rtc_32k_div.hw,
>> + },
>> + .num_parents = 2,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +struct clk_regmap a1_rtc_clk = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = RTC_BY_OSCIN_CTRL0,
>> + .bit_idx = 30,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "rtc_clk",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_rtc_32k_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +/* dsp a clk */
>> +static u32 mux_table_dsp_ab[] = { 0, 1, 2, 3, 4, 7 };
>> +static const struct clk_parent_data dsp_ab_clk_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_fclk_div2.hw },
>> + { .hw = &a1_fclk_div3.hw },
>> + { .hw = &a1_fclk_div5.hw },
>> + { .hw = &a1_hifi_pll.hw },
>> + { .hw = &a1_rtc_clk.hw },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_a_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 10,
>> + .table = mux_table_dsp_ab,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspa_a_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = dsp_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_a_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .shift = 0,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspa_a_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_a_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_a = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .bit_idx = 13,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspa_a",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_a_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>
> This CLK_IGNORE_UNUSED, if justified, needs to be explained
>
ok, DSP cowork withe ARM in A1, dsp clock shoud not be changed at runtime.
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_b_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 26,
>> + .table = mux_table_dsp_ab,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspa_b_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = dsp_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_b_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .shift = 16,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspa_b_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_b_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_b = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .bit_idx = 29,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspa_b",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_b_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPA_CLK_CTRL0,
>> + .mask = 0x1,
>> + .shift = 15,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspa_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = (const struct clk_parent_data []) {
>> + { .hw = &a1_dspa_a.hw },
>> + { .hw = &a1_dspa_b.hw },
>> + },
>> + .num_parents = 2,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_en_dspa = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPA_CLK_EN,
>> + .bit_idx = 1,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspa_en_dspa",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspa_en_nic = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPA_CLK_EN,
>> + .bit_idx = 0,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspa_en_nic",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspa_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +/* dsp b clk */
>> +static struct clk_regmap a1_dspb_a_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 10,
>> + .table = mux_table_dsp_ab,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspb_a_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = dsp_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_a_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .shift = 0,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspb_a_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_a_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_a = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .bit_idx = 13,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspb_a",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_a_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_b_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .mask = 0x7,
>> + .shift = 26,
>> + .table = mux_table_dsp_ab,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspb_b_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = dsp_ab_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_b_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .shift = 16,
>> + .width = 10,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspb_b_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_b_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_b = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .bit_idx = 29,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspb_b",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_b_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DSPB_CLK_CTRL0,
>> + .mask = 0x1,
>> + .shift = 15,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dspb_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_a.hw, &a1_dspb_b.hw,
>> + },
>> + .num_parents = 2,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_en_dspb = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPB_CLK_EN,
>> + .bit_idx = 1,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspb_en_dspb",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dspb_en_nic = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DSPB_CLK_EN,
>> + .bit_idx = 0,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dspb_en_nic",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dspb_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +/* 12M/24M clock */
>> +static struct clk_regmap a1_24m = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = CLK12_24_CTRL,
>> + .bit_idx = 11,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "24m",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor a1_24m_div2 = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "24m_div2",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_24m.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_12m = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = CLK12_24_CTRL,
>> + .bit_idx = 10,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "12m",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_24m_div2.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div2_divn_pre = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = CLK12_24_CTRL,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2_divn_pre",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div2.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_fclk_div2_divn = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = CLK12_24_CTRL,
>> + .bit_idx = 12,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "fclk_div2_divn",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_fclk_div2_divn_pre.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +/* gen clk */
>
> Either put something helpful or don't put anything
> For example explaining why there is a hole in the table bellow and what
> is parent 4 (if any) would be helpful.
ok, parent 2 is sys_pll_div16, sys pll and related clock are not
completeed, parent 4 is one of clock measurement source, it relies on
the clock measurement register configuration.
gen clock is a debug and monitor clock.
>
>> +static u32 gen_clk_table[] = { 0, 1, 3, 5, 6, 7, 8 };
>> +static const struct clk_parent_data gen_clk_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_rtc_clk.hw },
>> + { .hw = &a1_hifi_pll.hw },
>> + { .hw = &a1_fclk_div2.hw },
>> + { .hw = &a1_fclk_div3.hw },
>> + { .hw = &a1_fclk_div5.hw },
>> + { .hw = &a1_fclk_div7.hw },
>> +};
>> +
>> +static struct clk_regmap a1_gen_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = GEN_CLK_CTRL,
>> + .mask = 0xf,
>> + .shift = 12,
>> + .table = gen_clk_table,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "gen_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = gen_clk_parent_data,
>> + .num_parents = ARRAY_SIZE(gen_clk_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_gen_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = GEN_CLK_CTRL,
>> + .shift = 0,
>> + .width = 11,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "gen_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_gen_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_gen = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = GEN_CLK_CTRL,
>> + .bit_idx = 11,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "gen",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_gen_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_saradc_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = SAR_ADC_CLK_CTRL,
>> + .mask = 0x1,
>> + .shift = 9,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "saradc_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = (const struct clk_parent_data []) {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_sys_clk.hw, },
>> + },
>> + .num_parents = 2,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_saradc_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = SAR_ADC_CLK_CTRL,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "saradc_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_saradc_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_saradc_clk = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = SAR_ADC_CLK_CTRL,
>> + .bit_idx = 8,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "saradc_clk",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_saradc_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +/* pwm a/b/c/d parent data */
>> +static const struct clk_parent_data pwm_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_sys_clk.hw },
>> +};
>> +
>> +/*
>> + * add CLK_IGNORE_UNUSED flag for pwm controller GATE
>> + * clk core will disable unused clock, it may disable
>> + * vddcore voltage which contrlled by one pwm in bl21.
> ^
> typo
>
>> + * add the flag to avoid changing cpu voltage.
>
> 80 char per line is ok
> This comment would be better placed next to the corresponding flag
>
> Also you could explain that flag could be removed when CCF has some
> hand-off mechanism (similar comments you can copy in other driver)
>
ok, contrlled --> controlled
I will move the comment next to the flag
I have gotten the similar comments in g12a.c
>> + */
>> +/* pwm a clk */
>> +static struct clk_regmap a1_pwm_a_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = PWM_CLK_AB_CTRL,
>> + .mask = 0x1,
>> + .shift = 9,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pwm_a_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = pwm_parent_data,
>> + .num_parents = ARRAY_SIZE(pwm_parent_data),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_pwm_a_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = PWM_CLK_AB_CTRL,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pwm_a_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_pwm_a_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_pwm_a = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = PWM_CLK_AB_CTRL,
>> + .bit_idx = 8,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "pwm_a",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_pwm_a_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +

[...]

>> +/* usb bus clk */
>> +static const struct clk_parent_data usb_bus_parent_data[] = {
>> + { .fw_name = "xtal", },
>> + { .hw = &a1_sys_clk.hw },
>> + { .hw = &a1_fclk_div3.hw },
>> + { .hw = &a1_fclk_div5.hw },
>> +};
>> +
>> +static struct clk_regmap a1_usb_bus_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = USB_BUSCLK_CTRL,
>> + .mask = 0x3,
>> + .shift = 9,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "usb_bus_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = usb_bus_parent_data,
>> + .num_parents = ARRAY_SIZE(usb_bus_parent_data),
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>
> Again, every unused flag need to be properly explained
>
ok, I will confirm this flag
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_usb_bus_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = USB_BUSCLK_CTRL,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "usb_bus_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_usb_bus_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_usb_bus = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = USB_BUSCLK_CTRL,
>> + .bit_idx = 8,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "usb_bus",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_usb_bus_div.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +

[...]

>> +
>> +/* dmc clk */
>> +static const struct clk_hw *dmc_parent_hws[] = {
>> + &a1_fclk_div2.hw,
>> + &a1_fclk_div3.hw,
>> + &a1_fclk_div5.hw,
>> + &a1_hifi_pll.hw,
>> +};
>> +
>> +static struct clk_regmap a1_dmc_sel = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DMC_CLK_CTRL,
>> + .mask = 0x3,
>> + .shift = 9,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dmc_sel",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_hws = dmc_parent_hws,
>> + .num_parents = ARRAY_SIZE(dmc_parent_hws),
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dmc_div = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = DMC_CLK_CTRL,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dmc_div",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dmc_sel.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dmc_sel2 = {
>> + .data = &(struct clk_regmap_mux_data){
>> + .offset = DMC_CLK_CTRL,
>> + .mask = 0x1,
>> + .shift = 15,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "dmc_sel2",
>> + .ops = &clk_regmap_mux_ops,
>> + .parent_data = (const struct clk_parent_data []) {
>> + { .hw = &a1_dmc_div.hw },
>> + { .fw_name = "xtal", },
>> + },
>> + .num_parents = 2,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap a1_dmc = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = DMC_CLK_CTRL,
>> + .bit_idx = 8,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "dmc",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &a1_dmc_sel2.hw
>> + },
>> + .num_parents = 1,
>> + /*
>> + * add CLK_IGNORE_UNUSED to avoid hangup
>> + * DDR clock should not change at runtime
>> + */
>
> CRITICAL ? RO ops maybe ?
RO ops is better
>
>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + },
>> +};
>> +

[...]

>> +
>> +#define MESON_GATE(_name, _reg, _bit) \
>> + MESON_PCLK(_name, _reg, _bit, &a1_sys_clk.hw)
>> +
>> +/* CLKTREE_SYS_CLK_EN0 */
>
> Full caps is not ok ... and once again, try to add comment which helps
ok, I will add some useful comment.
>
>> +static MESON_GATE(a1_clk_tree, SYS_CLK_EN0, 0);
>> +static MESON_GATE(a1_reset_ctrl, SYS_CLK_EN0, 1);
>> +static MESON_GATE(a1_analog_ctrl, SYS_CLK_EN0, 2);
>> +static MESON_GATE(a1_pwr_ctrl, SYS_CLK_EN0, 3);
>> +static MESON_GATE(a1_pad_ctrl, SYS_CLK_EN0, 4);
>> +static MESON_GATE(a1_sys_ctrl, SYS_CLK_EN0, 5);
>> +static MESON_GATE(a1_temp_sensor, SYS_CLK_EN0, 6);
>> +static MESON_GATE(a1_am2axi_dev, SYS_CLK_EN0, 7);
>> +static MESON_GATE(a1_spicc_b, SYS_CLK_EN0, 8);
>> +static MESON_GATE(a1_spicc_a, SYS_CLK_EN0, 9);
>> +static MESON_GATE(a1_clk_msr, SYS_CLK_EN0, 10);
>> +static MESON_GATE(a1_audio, SYS_CLK_EN0, 11);
>> +static MESON_GATE(a1_jtag_ctrl, SYS_CLK_EN0, 12);
>> +static MESON_GATE(a1_saradc, SYS_CLK_EN0, 13);
>> +static MESON_GATE(a1_pwm_ef, SYS_CLK_EN0, 14);
>> +static MESON_GATE(a1_pwm_cd, SYS_CLK_EN0, 15);
>> +static MESON_GATE(a1_pwm_ab, SYS_CLK_EN0, 16);
>> +static MESON_GATE(a1_cec, SYS_CLK_EN0, 17);
>> +static MESON_GATE(a1_i2c_s, SYS_CLK_EN0, 18);
>> +static MESON_GATE(a1_ir_ctrl, SYS_CLK_EN0, 19);
>> +static MESON_GATE(a1_i2c_m_d, SYS_CLK_EN0, 20);
>> +static MESON_GATE(a1_i2c_m_c, SYS_CLK_EN0, 21);
>> +static MESON_GATE(a1_i2c_m_b, SYS_CLK_EN0, 22);
>> +static MESON_GATE(a1_i2c_m_a, SYS_CLK_EN0, 23);
>> +static MESON_GATE(a1_acodec, SYS_CLK_EN0, 24);
>> +static MESON_GATE(a1_otp, SYS_CLK_EN0, 25);
>> +static MESON_GATE(a1_sd_emmc_a, SYS_CLK_EN0, 26);
>> +static MESON_GATE(a1_usb_phy, SYS_CLK_EN0, 27);
>> +static MESON_GATE(a1_usb_ctrl, SYS_CLK_EN0, 28);
>> +static MESON_GATE(a1_sys_dspb, SYS_CLK_EN0, 29);
>> +static MESON_GATE(a1_sys_dspa, SYS_CLK_EN0, 30);
>> +static MESON_GATE(a1_dma, SYS_CLK_EN0, 31);
>> +/* CLKTREE_SYS_CLK_EN1 */
>> +static MESON_GATE(a1_irq_ctrl, SYS_CLK_EN1, 0);
>> +static MESON_GATE(a1_nic, SYS_CLK_EN1, 1);
>> +static MESON_GATE(a1_gic, SYS_CLK_EN1, 2);
>> +static MESON_GATE(a1_uart_c, SYS_CLK_EN1, 3);
>> +static MESON_GATE(a1_uart_b, SYS_CLK_EN1, 4);
>> +static MESON_GATE(a1_uart_a, SYS_CLK_EN1, 5);
>> +static MESON_GATE(a1_sys_psram, SYS_CLK_EN1, 6);
>> +static MESON_GATE(a1_rsa, SYS_CLK_EN1, 8);
>> +static MESON_GATE(a1_coresight, SYS_CLK_EN1, 9);
>> +/* CLKTREE_AXI_CLK_EN */
>> +static MESON_GATE(a1_am2axi_vad, AXI_CLK_EN, 0);
>> +static MESON_GATE(a1_audio_vad, AXI_CLK_EN, 1);
>> +static MESON_GATE(a1_axi_dmc, AXI_CLK_EN, 3);
>> +static MESON_GATE(a1_axi_psram, AXI_CLK_EN, 4);
>> +static MESON_GATE(a1_ramb, AXI_CLK_EN, 5);
>> +static MESON_GATE(a1_rama, AXI_CLK_EN, 6);
>> +static MESON_GATE(a1_axi_spifc, AXI_CLK_EN, 7);
>> +static MESON_GATE(a1_axi_nic, AXI_CLK_EN, 8);
>> +static MESON_GATE(a1_axi_dma, AXI_CLK_EN, 9);
>> +static MESON_GATE(a1_cpu_ctrl, AXI_CLK_EN, 10);
>> +static MESON_GATE(a1_rom, AXI_CLK_EN, 11);
>> +static MESON_GATE(a1_prod_i2c, AXI_CLK_EN, 12);
>> +

[...]

>> +
>> +/* Convenience table to populate regmap in .probe
>> + * Peripheral clock register base address is 0xfe000800
>
> this info will be in DT
I will remove the address commit
>
>> + */

[...]

>> +
>> +/*
>> + * cpu clock register base address is 0xfd000080
>> + */
>> +static struct clk_regmap *const a1_cpu_clk_regmaps[] = {
>> + /* TODO */
>> +};
>> +
>> +/*
>> + * pll clock register base address is 0xfe007c00
>> + */
>> +static struct clk_regmap *const a1_pll_clk_regmaps[] = {
>> + &a1_fixed_pll_dco,
>> + &a1_fixed_pll,
>> + &a1_hifi_pll,
>> + &a1_fclk_div2,
>> + &a1_fclk_div3,
>> + &a1_fclk_div5,
>> + &a1_fclk_div7,
>> +};
>> +
>> +static struct regmap_config clkc_regmap_config = {
>> + .reg_bits = 32,
>> + .val_bits = 32,
>> + .reg_stride = 4,
>> +};
>> +
>> +static struct regmap *a1_regmap_resource(struct device *dev, char *name)
>> +{
>> + struct resource res;
>> + void __iomem *base;
>> + int i;
>> + struct device_node *node = dev->of_node;
>> +
>> + i = of_property_match_string(node, "reg-names", name);
>> + if (of_address_to_resource(node, i, &res))
>> + return ERR_PTR(-ENOENT);
>> +
>> + base = devm_ioremap_resource(dev, &res);
>> + if (IS_ERR(base))
>> + return ERR_CAST(base);
>> +
>> + clkc_regmap_config.max_register = resource_size(&res) - 4;
>> + clkc_regmap_config.name = devm_kasprintf(dev, GFP_KERNEL,
>> + "%s-%s", node->name,
>> + name);
>> + if (!clkc_regmap_config.name)
>> + return ERR_PTR(-ENOMEM);
>> +
>> + return devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
>> +}
>> +
>> +static int a1_clkc_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct regmap *peripheral_map, *pll_map, *cpu_map;
>> + int ret, i;
>> +
>> + /* Get regmap for different clock area */
>> + peripheral_map = a1_regmap_resource(dev, "peripheral");
>> + if (IS_ERR(peripheral_map)) {
>> + dev_err(dev, "peripheral clk registers not found\n");
>> + return PTR_ERR(peripheral_map);
>> + }
>> +
>> + pll_map = a1_regmap_resource(dev, "pll");
>> + if (IS_ERR(pll_map)) {
>> + dev_err(dev, "pll clk registers not found\n");
>> + return PTR_ERR(pll_map);
>> + }
>> +
>> + cpu_map = a1_regmap_resource(dev, "cpu");
>> + if (IS_ERR(cpu_map)) {
>> + dev_err(dev, "cpu clk registers not found\n");
>> + return PTR_ERR(cpu_map);
>> + }
>> +
>> + /* Populate regmap for the regmap backed clocks */
>> + for (i = 0; i < ARRAY_SIZE(a1_clk_regmaps); i++)
>> + a1_clk_regmaps[i]->map = peripheral_map;
>> +
>> + for (i = 0; i < ARRAY_SIZE(a1_cpu_clk_regmaps); i++)
>> + a1_cpu_clk_regmaps[i]->map = cpu_map;
>> +
>> + for (i = 0; i < ARRAY_SIZE(a1_pll_clk_regmaps); i++)
>> + a1_pll_clk_regmaps[i]->map = pll_map;
>
> Unless you have a rock solid reason why you absolutely need to make
> single controller out of this 3 regions, Nack.
>
As comment replying in
Documentation/devicetree/bindings/clock/amlogic,a1-clkc.yaml, I will
implement three clock drivers.
>> +
>> + for (i = 0; i < a1_hw_onecell_data.num; i++) {
>> + /* array might be sparse */
>> + if (!a1_hw_onecell_data.hws[i])
>> + continue;
>> +
>> + ret = devm_clk_hw_register(dev, a1_hw_onecell_data.hws[i]);
>> + if (ret) {
>> + dev_err(dev, "Clock registration failed\n");
>> + return ret;
>> + }
>> + }
>> +
>> + return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
>> + &a1_hw_onecell_data);
>> +}
>> +
>> +static const struct of_device_id clkc_match_table[] = {
>> + { .compatible = "amlogic,a1-clkc" },
>> + { /* sentinel */ }
>> +};
>> +
>> +static struct platform_driver a1_driver = {
>> + .probe = a1_clkc_probe,
>> + .driver = {
>> + .name = "a1-clkc",
>> + .of_match_table = clkc_match_table,
>> + },
>> +};
>> +
>> +builtin_platform_driver(a1_driver);
>> diff --git a/drivers/clk/meson/a1.h b/drivers/clk/meson/a1.h
>> new file mode 100644
>> index 0000000..f2291c4
>> --- /dev/null
>> +++ b/drivers/clk/meson/a1.h
>> @@ -0,0 +1,172 @@
>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>> +/*
>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>> + */
>> +
>> +#ifndef __A1_H
>> +#define __A1_H
>> +
>> +/*
>> + * peripheral clock controller register address
>> + * APB_BASE: APB0_BASE_ADDR = 0xfe000800
>
> Again this info is DT and might become wrong if your controller is ever
> compatible with another SoC
>
I will remove the address comment, the right address is 0xfe000080.
>> + */
>> +#define SYS_OSCIN_CTRL 0x0
>> +#define RTC_BY_OSCIN_CTRL0 0x4
>> +#define RTC_BY_OSCIN_CTRL1 0x8
>> +#define RTC_CTRL 0xc
>> +#define SYS_CLK_CTRL0 0x10
>> +#define AXI_CLK_CTRL0 0x14
>> +#define SYS_CLK_EN0 0x1c
>> +#define SYS_CLK_EN1 0x20
>> +#define AXI_CLK_EN 0x24
>> +#define DSPA_CLK_EN 0x28
>> +#define DSPB_CLK_EN 0x2c
>> +#define DSPA_CLK_CTRL0 0x30
>> +#define DSPB_CLK_CTRL0 0x34
>> +#define CLK12_24_CTRL 0x38
>> +#define GEN_CLK_CTRL 0x3c
>> +#define TIMESTAMP_CTRL0 0x40
>> +#define TIMESTAMP_CTRL1 0x44
>> +#define TIMESTAMP_CTRL2 0x48
>> +#define TIMESTAMP_VAL0 0x4c
>> +#define TIMESTAMP_VAL1 0x50
>> +#define TIMEBASE_CTRL0 0x54
>> +#define TIMEBASE_CTRL1 0x58
>> +#define SAR_ADC_CLK_CTRL 0xc0
>> +#define PWM_CLK_AB_CTRL 0xc4
>> +#define PWM_CLK_CD_CTRL 0xc8
>> +#define PWM_CLK_EF_CTRL 0xcc
>> +#define SPICC_CLK_CTRL 0xd0
>> +#define TS_CLK_CTRL 0xd4
>> +#define SPIFC_CLK_CTRL 0xd8
>> +#define USB_BUSCLK_CTRL 0xdc
>> +#define SD_EMMC_CLK_CTRL 0xe0
>> +#define CECA_CLK_CTRL0 0xe4
>> +#define CECA_CLK_CTRL1 0xe8
>> +#define CECB_CLK_CTRL0 0xec
>> +#define CECB_CLK_CTRL1 0xf0
>> +#define PSRAM_CLK_CTRL 0xf4
>> +#define DMC_CLK_CTRL 0xf8
>> +#define FCLK_DIV1_SEL 0xfc
>> +#define TST_CTRL 0x100
>> +/*
>> + * For PLL register offset
>> + * APB_BASE: APB0_BASE_ADDR = 0xfe007c00
>> + */
>> +#define ANACTRL_FIXPLL_CTRL0 0x80
>> +#define ANACTRL_FIXPLL_CTRL1 0x84
>> +#define ANACTRL_FIXPLL_CTRL2 0x88
>> +#define ANACTRL_FIXPLL_CTRL3 0x8c
>> +#define ANACTRL_FIXPLL_CTRL4 0x90
>> +#define ANACTRL_FIXPLL_STS 0x94
>> +#define ANACTRL_SYSPLL_CTRL0 0x100
>> +#define ANACTRL_SYSPLL_CTRL1 0x104
>> +#define ANACTRL_SYSPLL_CTRL2 0x108
>> +#define ANACTRL_SYSPLL_CTRL3 0x10c
>> +#define ANACTRL_SYSPLL_CTRL4 0x110
>> +#define ANACTRL_SYSPLL_STS 0x114
>> +#define ANACTRL_HIFIPLL_CTRL0 0x140
>> +#define ANACTRL_HIFIPLL_CTRL1 0x144
>> +#define ANACTRL_HIFIPLL_CTRL2 0x148
>> +#define ANACTRL_HIFIPLL_CTRL3 0x14c
>> +#define ANACTRL_HIFIPLL_CTRL4 0x150
>> +#define ANACTRL_HIFIPLL_STS 0x154
>> +#define ANACTRL_AUDDDS_CTRL0 0x180
>> +#define ANACTRL_AUDDDS_CTRL1 0x184
>> +#define ANACTRL_AUDDDS_CTRL2 0x188
>> +#define ANACTRL_AUDDDS_CTRL3 0x18c
>> +#define ANACTRL_AUDDDS_CTRL4 0x190
>> +#define ANACTRL_AUDDDS_STS 0x194
>> +#define ANACTRL_MISCTOP_CTRL0 0x1c0
>> +#define ANACTRL_POR_CNTL 0x208
>> +/*
>> + * CPU clok register offset
>> + * APB_BASE: APB1_BASE_ADDR = 0xfd000080
>> + */
>> +#define CPUCTRL_CLK_CTRL0 0x00
>> +#define CPUCTRL_CLK_CTRL1 0x04
>> +#define CPUCTRL_CLK_CTRL2 0x08
>> +#define CPUCTRL_CLK_CTRL3 0x0c
>> +#define CPUCTRL_CLK_CTRL4 0x10
>> +#define CPUCTRL_CLK_CTRL5 0x14
>> +#define CPUCTRL_CLK_CTRL6 0x18
>> +#define CPUCTRL_CLK_CTRL7 0x1c
>> +
>> +#define CLKID_FIXED_PLL_DCO 0
>> +#define CLKID_SYS_A_SEL 10
>> +#define CLKID_SYS_A_DIV 11
>> +#define CLKID_SYS_A 12
>> +#define CLKID_SYS_B_SEL 13
>> +#define CLKID_SYS_B_DIV 14
>> +#define CLKID_SYS_B 15
>> +#define CLKID_XTAL_CLKTREE 18
>> +#define CLKID_XTAL_FIXPLL 19
>> +#define CLKID_XTAL_USB_PHY 20
>> +#define CLKID_XTAL_USB_CTRL 21
>> +#define CLKID_XTAL_HIFIPLL 22
>> +#define CLKID_XTAL_SYSPLL 23
>> +#define CLKID_XTAL_DDS 24
>> +#define CLKID_DSPA_A_SEL 78
>> +#define CLKID_DSPA_A_DIV 79
>> +#define CLKID_DSPA_A 80
>> +#define CLKID_DSPA_B_SEL 81
>> +#define CLKID_DSPA_B_DIV 82
>> +#define CLKID_DSPA_B 83
>> +#define CLKID_DSPB_A_SEL 85
>> +#define CLKID_DSPB_A_DIV 86
>> +#define CLKID_DSPB_A 87
>> +#define CLKID_DSPB_B_SEL 88
>> +#define CLKID_DSPB_B_DIV 89
>> +#define CLKID_DSPB_B 90
>> +#define CLKID_RTC_32K_CLKIN 96
>> +#define CLKID_RTC_32K_DIV 97
>> +#define CLKID_RTC_32K_XTAL 98
>> +#define CLKID_RTC_32K_SEL 99
>> +#define CLKID_CECB_32K_CLKIN 106
>> +#define CLKID_CECB_32K_DIV 107
>> +#define CLKID_CECB_32K_SEL_PRE 108
>> +#define CLKID_CECB_32K_SEL 109
>> +#define CLKID_CECA_32K_CLKIN 101
>> +#define CLKID_CECA_32K_DIV 102
>> +#define CLKID_CECA_32K_SEL_PRE 103
>> +#define CLKID_CECA_32K_SEL 104
>> +#define CLKID_DIV2_PRE 113
>> +#define CLKID_24M_DIV2 115
>> +#define CLKID_GEN_SEL 116
>> +#define CLKID_GEN_DIV 117
>> +#define CLKID_SARADC_DIV 120
>> +#define CLKID_PWM_A_SEL 122
>> +#define CLKID_PWM_A_DIV 123
>> +#define CLKID_PWM_B_SEL 125
>> +#define CLKID_PWM_B_DIV 126
>> +#define CLKID_PWM_C_SEL 128
>> +#define CLKID_PWM_C_DIV 129
>> +#define CLKID_PWM_D_SEL 131
>> +#define CLKID_PWM_D_DIV 132
>> +#define CLKID_PWM_E_SEL 134
>> +#define CLKID_PWM_E_DIV 135
>> +#define CLKID_PWM_F_SEL 137
>> +#define CLKID_PWM_F_DIV 138
>> +#define CLKID_SPICC_SEL 140
>> +#define CLKID_SPICC_DIV 141
>> +#define CLKID_SPICC_SEL2 142
>> +#define CLKID_TS_DIV 144
>> +#define CLKID_SPIFC_SEL 146
>> +#define CLKID_SPIFC_DIV 147
>> +#define CLKID_SPIFC_SEL2 148
>> +#define CLKID_USB_BUS_SEL 150
>> +#define CLKID_USB_BUS_DIV 151
>> +#define CLKID_SD_EMMC_SEL 153
>> +#define CLKID_SD_EMMC_DIV 154
>> +#define CLKID_SD_EMMC_SEL2 155
>> +#define CLKID_PSRAM_SEL 157
>> +#define CLKID_PSRAM_DIV 158
>> +#define CLKID_PSRAM_SEL2 159
>> +#define CLKID_DMC_SEL 161
>> +#define CLKID_DMC_DIV 162
>> +#define CLKID_DMC_SEL2 163
>> +#define NR_CLKS 165
>> +
>> +#include <dt-bindings/clock/a1-clkc.h>
>> +
>> +#endif /* __A1_H */
>> --
>> 1.9.1
>
> .
>

\
 
 \ /
  Last update: 2019-09-27 11:55    [W:0.149 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site