lkml.org 
[lkml]   [2019]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] ARM: dts: add Netronix E60K02 board common file
Hi Andreas,

thanks for the patch.

On 19-09-27 08:14, Andreas Kemnade wrote:
> The Netronix board E60K02 can be found some several Ebook-Readers,
> at least the Kobo Clara HD and the Tolino Shine 3. The board
> is equipped with different SoCs.
>
> For now the following peripherals are included:
> - LED
> - Power Key
> - Cover (gpio via hall sensor)
> - RC5T619 PMIC (the kernel misses support for rtc and charger
> subdevices).
> - Backlight via lm3630a
> - Wifi sdio chip detection (mmc-powerseq and stuff)
>
> It is based on vendor kernel but heavily reworked due to many
> changed bindings.
>
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> ---
> backligt dependencies:
> module autoloading:
> https://patchwork.kernel.org/patch/11139987/
> enable-gpios property:
> https://patchwork.kernel.org/patch/11143795/
>
> arch/arm/boot/dts/e60k02.dtsi | 339 ++++++++++++++++++++++++++++++++++
> 1 file changed, 339 insertions(+)
> create mode 100644 arch/arm/boot/dts/e60k02.dtsi
>
> diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/e60k02.dtsi
> new file mode 100644
> index 000000000000..c4fa8e314e2e
> --- /dev/null
> +++ b/arch/arm/boot/dts/e60k02.dtsi
> @@ -0,0 +1,339 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2019 Andreas Kemnade
> + * based on works
> + * Copyright 2016 Freescale Semiconductor, Inc.
> + * and
> + * Copyright (C) 2014 Ricoh Electronic Devices Co., Ltd
> + *
> + * Netronix E60K02 board common.
> + * This board is equipped with different SoCs and
> + * found in ebook-readers like the Kobo Clara HD (with i.MX6SLL) and
> + * the Tolino Shine 3 (with i.MX6SL)
> + */
> +
> +/ {
> +
> + memory {
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + post-power-on-delay-ms = <20>;
> + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;

Can you add a pinctrl-entry here please? The general rule is to mux
things where you use it.

> + };

Please reorder the whole dt alphabetical.

> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;

Drop the regultors { } container especially if we only have a single
regulator.

> +
> + reg_sd3_vmmc: wifi_regulator {

Either use:
reg_sd3_vmmc: regulator-sd3-vmmc
or
reg_wifi: regulator-wifi

> + compatible = "regulator-fixed";
> + regulator-name = "SD3_SPWR";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> +
> + gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;

Please add a pinctrl here to mux this gpio.

> + enable-active-high;
> +
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_led>;

Please move all muxing you made here into this file or add phandles so
the dts file need to add only the muxing stuff. This applies to all
pinctrl you made here.

> +
> + GLED {
> + gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "timer";
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> + power {
> + label = "Power";
> + gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_POWER>;

Add missing header: dt-bindings/input/input.h to use this.

> + gpio-key,wakeup;
> + };
> + cover {
> + label = "Cover";
> + gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
> + linux,code = <SW_LID>;
> + linux,input-type = <0x05>; /* EV_SW */

In the header above EV_SW is also specified so please use it here.

> + gpio-key,wakeup;
> + };
> + };
> +
> +};
> +
> +
> +

Whitespaces

> +&audmux {
> + pinctrl-names = "default";
> + status = "disabled";

Why you mentioned a pinctrl-names here without the mux? Do we need the
status line here? The common case is that such devices are off by
default/the base dt.

> +};
> +
> +&snvs_rtc {
> + status = "disabled";

Same applies here.

> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default","sleep";
> + pinctrl-0 = <&pinctrl_i2c1 &pinctrl_lm3630a_bl_gpio>;

The &pinctrl_lm3630a_bl_gpio should be moved into the lm3630a node.

> + pinctrl-1 = <&pinctrl_i2c1_sleep>;
> + status = "okay";
> +
> + lm3630a: lm3630a-i2c@36 {

please name it backlight@36

> + reg = <0x36>;
> + status = "ok";

status lines are always be the last and if it is okay you can drop it
because the default is okay.

> +
> + compatible = "ti,lm3630a";
> + enable-gpios = <&gpio2 10 0>;

Please use GPIO_ACTIVE_HIGH.

> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + led@0 {
> + reg = <0>;
> + led-sources = <0>;
> + label = "backlight_warm";
> + default-brightness = <0>;
> + max-brightness = <255>;
> + };
> +
> + led@1 {
> + reg = <1>;
> + led-sources = <1>;
> + label = "backlight_cold";
> + default-brightness = <0>;
> + max-brightness = <255>;
> + };
> +
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3 &pinctrl_ricoh_gpio>;

Device mux goes into the device.

> + status = "okay";
> +
> + ricoh619: ricoh619-i2c@32 {

Please name it pmic@32

> + compatible = "ricoh,rc5t619";
> + reg = <0x32>;
> +
> + system-power-controller;
> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> + gpio_chg = <&gpio5 15 GPIO_ACTIVE_LOW>;
> + gpio_bat_low = <&gpio3 28 GPIO_ACTIVE_LOW>;
> + };
> +
> +};
> +
> +&ricoh619
> +{

Nope. The whole bunch should be moved to the place above where add the
device.

> + compatible = "ricoh,rc5t619";
> +
> + regulators {
> + ricoh619_dcdc1_reg: DCDC1 {

please drop the ricoh619_ prefix.

> + regulator-name = "DCDC1";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;

regulator-suspend-microvolt is deprecated. Please use
regulator-suspend-min-microvolt and regulator-suspend-max-microvolt.

> + };
> + };
> +
> + /* Core3_3V3 */
> + ricoh619_dcdc2_reg: DCDC2 {
> + regulator-name = "DCDC2";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + ricoh619_dcdc3_reg: DCDC3 {
> + regulator-name = "DCDC3";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-always-on;//

Remove //

> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1140000>;
> + };
> + };
> +
> + /* Core4_1V2 */
> + ricoh619_dcdc4_reg: DCDC4 {
> + regulator-name = "DCDC4";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1140000>;
> + };
> + };
> +
> + /* Core4_1V8 */
> + ricoh619_dcdc5_reg: DCDC5 {
> + regulator-name = "DCDC5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1700000>;
> + };
> + };
> +
> + /* IR_3V3 */
> + ricoh619_ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + //regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + /* Core1_3V3 */
> + ricoh619_ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + /* Core5_1V2 */
> + ricoh619_ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ricoh619_ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-boot-on;
> + };
> +
> + /* SPD_3V3 */
> + ricoh619_ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + /* DDR_0V6 */
> + ricoh619_ldo6_reg: LDO6 {
> + regulator-name = "LDO6";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + /* VDD_PWM */
> + ricoh619_ldo7_reg: LDO7 {
> + regulator-name = "LDO7";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + /* ldo_1v8 */
> + ricoh619_ldo8_reg: LDO8 {
> + regulator-name = "LDO8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ricoh619_ldo9_reg: LDO9 {
> + regulator-name = "LDO9";
> + regulator-boot-on;
> + };
> +
> + ricoh619_ldo10_reg: LDO10 {
> + regulator-name = "LDO10";
> + regulator-boot-on;
> + };
> +
> + ricoh619_ldortc1_reg: LDORTC1 {
> + regulator-name = "LDORTC1";
> + regulator-boot-on;
> + };
> +
> + ricoh619_ldortc2_reg: LDORTC2 {
> + regulator-name = "LDORTC2";
> + regulator-boot-on;
> + };
> + };
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + status = "disabled";
> +};

Can be dropped

> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + pinctrl-3 = <&pinctrl_usdhc2_sleep>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
> + pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_pwr>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + pinctrl-3 = <&pinctrl_usdhc3_sleep>, <&pinctrl_usdhc3_pwr>;
> + vmmc-supply = <&reg_sd3_vmmc>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + cap-power-off-card;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + pinctrl-names = "default";
> + disable-over-current;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + status = "okay";
> +};
> +
> +
> +&ssi2 {
> + status = "disabled";
> +};

Can be dropped.


Thanks for your patch.

Regards,
Marco

> +
> --
> 2.20.1
>
>
>

--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

\
 
 \ /
  Last update: 2019-09-27 11:48    [W:0.064 / U:2.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site