lkml.org 
[lkml]   [2019]   [Sep]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] PCI / PM: Don't runtime suspend when device only supports wakeup from D0
From
Date
at 21:45, Bjorn Helgaas <helgaas@kernel.org> wrote:

> On Fri, Jul 05, 2019 at 03:02:01PM +0800, Kai-Heng Feng wrote:
>> at 19:57, Bjorn Helgaas <helgaas@kernel.org> wrote:
>>> On Mon, May 27, 2019 at 11:57:47AM -0500, Bjorn Helgaas wrote:
>
>>>> I'm wondering if this platform has a firmware defect. Here's my
>>>> thinking. The xHC is a Root Complex Integrated Endpoint, so its PME
>>>> signaling is a little unusual.
>>>>
>>>> The typical scenario is that a PCIe device is below a Root Port. In
>>>> that case, it would send a PME Message upstream to the Root Port. Per
>>>> PCIe r4.0, sec 6.1.6, when configured for native PME support (for ACPI
>>>> systems, I assume this means "when firmware has granted PME control to
>>>> the OS via _OSC"), the Root Port would generate a normal PCI INTx or
>>>> MSI interrupt:
>>>>
>>>> PCI Express-aware software can enable a mode where the Root Complex
>>>> signals PME via an interrupt. When configured for native PME
>>>> support, a Root Port receives the PME Message and sets the PME
>>>> Status bit in its Root Status register. If software has set the PME
>>>> Interrupt Enable bit in the Root Control register to 1b, the Root
>>>> Port then generates an interrupt.
>>>>
>>>> But on this platform the xHC is a Root Complex Integrated Endpoint, so
>>>> there is no Root Port upstream from it, and that mechanism can't be
>>>> used. Per PCIe r4.0, sec 1.3.2.3, RCiEPs signal PME via "the same
>>>> mechanism as PCI systems" or via Root Complex Event Collectors:
>>>>
>>>> An RCiEP must signal PME and error conditions through the same
>>>> mechanisms used on PCI systems. If a Root Complex Event Collector is
>>>> implemented, an RCiEP may optionally signal PME and error conditions
>>>> through a Root Complex Event Collector.
>>>>
>>>> This platform has no Root Complex Event Collectors, so the xHC should
>>>> signal PME via the same mechanism as PCI systems, i.e., asserting a
>>>> PME# signal. I think this means the OS cannot use native PCIe PME
>>>> control because it doesn't know what interrupt PME# is connected to.
>>>> The PCI Firmware Spec r3.2, sec 4.5.1 (also quoted in ACPI v6.2, sec
>>>> 6.2.11.3), says:
>>>>
>>>> PCI Express Native Power Management Events control
>>>>
>>>> The firmware sets this bit to 1 to grant control over PCI Express
>>>> native power management event interrupts (PMEs). If firmware
>>>> allows the operating system control of this feature, then in the
>>>> context of the _OSC method, it must ensure that all PMEs are
>>>> routed to root port interrupts as described in the PCI Express
>>>> Base Specification.
>>>>
>>>> This platform cannot route all PMEs to Root Port interrupts because
>>>> the xHC RCiEP cannot report PME via a Root Port, so I think its _OSC
>>>> method should not grant control of PCIe Native Power Management Events
>>>> to the OS, and I think that would mean we have to use the ACPI
>>>> mechanism for PME on this platform.
>>>>
>>>> Can you confirm or deny any of this line of reasoning? I'm wondering
>>>> if there's something wrong with the platform's _OSC, so Linux thinks
>>>> it can use native PME, but that doesn't work for this device.
>>>>
>>>>> It’s a platform in development so the name can’t be disclosed.
>>>>
>>>> Please attach a complete dmesg log to the bugzilla. You can remove
>>>> identifying details like the platform name, but I want to see the
>>>> results of the _OSC negotiation.
>>>
>>> Thanks for the dmesg log
>>> (https://bugzilla.kernel.org/attachment.cgi?id=283109). It shows:
>>>
>>> acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
>>> acpi PNP0A08:00: _OSC: platform does not support [SHPCHotplug LTR]
>>> acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
>>>
>>> I think it is incorrect for the platform to give the OS native control
>>> over PME because the OS has no way to know how the RCiEP PMEs are
>>> routed. But it would be interesting to know how BIOSes on other
>>> platforms with RCiEPs handle this, and I did post a question to the
>>> PCI-SIG to see if there's any guidance there.
>>
>> Is there any update from PCI-SIG?
>
> Yes, but I did a terrible job asking the question, so we didn't
> really get an answer for this situation. The thread on the forum is
> https://forum.pcisig.com/viewtopic.php?f=85&t=1081 (requires PCI-SIG
> login, unfortunately). My question was:
>
> Given an RCiEP that supports PME, can firmware grant control over
> native power management events to the OS?
>
> The PCI Firmware spec, r3.2, sec 4.5.1, says:
>
> PCI Express Native Power Management Events control
>
> The firmware sets this bit to 1 to grant control over PCI Express
> native power management event interrupts (PMEs). If firmware
> allows the operating system control of this feature, then in the
> context of the _OSC method, it must ensure that all PMEs are
> routed to root port interrupts as described in the PCI Express
> Base Specification.
>
> I don't think there's a mechanism for RCiEPs to route PMEs to a Root
> Port interrupt.
>
> PCIe r4.0, sec 1.3.2.3, says:
>
> An RCiEP must signal PME and error conditions through the same
> mechanisms used on PCI systems. If a Root Complex Event Collector
> is implemented, an RCiEP may optionally signal PME and error
> conditions through a Root Complex Event Collector.
>
> If the OS can be granted native PME control, how does it learn where
> the RCiEP PME is routed?
>
> And the response from Robert Gough:
>
> The routing of root complex devices- Root Ports and Root Complex
> Integrated Endpionts- to Event Collectors is described in the Event
> Collector's RCEC Endpoint Association Capability Structure.
>
> In order for OSPM to process PMEs routed to an Event Collector, the
> source of the PME is found in the PME Requester ID field within the
> Root Status register of the Event Collector, in the same way that
> PME messages from children of Root Ports are serviced.
>
> I just posted this follow-up question:
>
> Thanks, that clarifies one piece. The PCI Firmware spec, r3.2, sec
> 4.5.1, says that if firmware allows OSPM control of PME, all PMEs
> should be routed to Root Port interrupts. Your answer suggests that
> this should be updated to say something like "all PMEs are routed to
> Root Port *or RCEC* interrupts".
>
> The piece I still don't understand is what happens when firmware
> allows OSPM control of PME in a system with an RCiEP but no RCEC.
> Where are PMEs from the RCiEP routed, and how does OSPM discover
> that? Or is it simply illegal for firmware to allow OSPM control of
> PME in that case?
>
> The system we're looking at doesn't have any RCECs, so I don't think
> the Root Complex Event Collector Endpoint Association Capability (what
> a mouthful :)) is applicable, but I don't think Linux currently has
> any support for it, so I think we're likely to trip over similar
> issues on systems that do have RCECs.
>
> It would be good if somebody added support for that capability.

I just found the same issue on another Stoney Ridge laptop so I’d like to
bring up this issue again.

The original approach I took is based on the feed back from BIOS team. They
modified the return value of _S0W method to 0, to prevent the device from
being runtime suspended.

But since the D0 PME# doesn’t work, I think maybe it’s better to just
remove D0 PME# from its PM CAP?
I’ll send a patch with quirk to the mailing list.

Kai-Heng

>
> Bjorn


\
 
 \ /
  Last update: 2019-09-02 15:49    [W:0.109 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site