lkml.org 
[lkml]   [2019]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3] drm: bridge/dw_hdmi: add audio sample channel status setting
On Thu, Sep 12, 2019 at 12:54 AM Jernej Škrabec <jernej.skrabec@siol.net> wrote:
>
> Dne sreda, 11. september 2019 ob 18:23:59 CEST je Neil Armstrong napisal(a):
> > On 11/09/2019 10:26, Cheng-Yi Chiang wrote:
> > > From: Yakir Yang <ykk@rock-chips.com>
> > >
> > > When transmitting IEC60985 linear PCM audio, we configure the
> > > Aduio Sample Channel Status information in the IEC60958 frame.
> > > The status bit is already available in iec.status of hdmi_codec_params.
> > >
> > > This fix the issue that audio does not come out on some monitors
> > > (e.g. LG 22CV241)
> > >
> > > Note that these registers are only for interfaces:
> > > I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
> > > (AHBAUDDMA).
> > > For S/PDIF interface this information comes from the stream.
> > >
> > > Currently this function dw_hdmi_set_channel_status is only called
> > > from dw-hdmi-i2s-audio in I2S setup.
> > >
> > > Signed-off-by: Yakir Yang <ykk@rock-chips.com>
> > > Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
> > > ---
> > >
> > > Change from v2 to v3:
> > > 1. Reuse what is already set in iec.status in hw_param.
> > > 2. Remove all useless definition of registers and values.
> > > 3. Note that the original sampling frequency is not written to
> > >
> > > the channel status as we reuse create_iec958_consumer in pcm_iec958.c.
> > > Without that it can still play audio fine.
> > >
> > > .../drm/bridge/synopsys/dw-hdmi-i2s-audio.c | 1 +
> > > drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 20 +++++++++++++++++++
> > > drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 2 ++
> > > include/drm/bridge/dw_hdmi.h | 1 +
> > > 4 files changed, 24 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c index
> > > 34d8e837555f..20f4f92dd866 100644
> > > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
> > > @@ -102,6 +102,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev,
> > > void *data,>
> > > }
> > >
> > > dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate);
> > >
> > > + dw_hdmi_set_channel_status(hdmi, hparms->iec.status);
> > >
> > > dw_hdmi_set_channel_count(hdmi, hparms->channels);
> > > dw_hdmi_set_channel_allocation(hdmi, hparms-
> >cea.channel_allocation);
> > >
> > > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index
> > > bd65d0479683..aa7efd4da1c8 100644
> > > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > @@ -582,6 +582,26 @@ static unsigned int hdmi_compute_n(unsigned int freq,
> > > unsigned long pixel_clk)>
> > > return n;
> > >
> > > }
> > >
> > > +/*
> > > + * When transmitting IEC60958 linear PCM audio, these registers allow to
> > > + * configure the channel status information of all the channel status
> > > + * bits in the IEC60958 frame. For the moment this configuration is only
> > > + * used when the I2S audio interface, General Purpose Audio (GPA),
> > > + * or AHB audio DMA (AHBAUDDMA) interface is active
> > > + * (for S/PDIF interface this information comes from the stream).
> > > + */
> > > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi,
> > > + u8 *channel_status)
> > > +{
> > > + /*
> > > + * Set channel status register for frequency and word length.
> > > + * Use default values for other registers.
> > > + */
> > > + hdmi_writeb(hdmi, channel_status[3], HDMI_FC_AUDSCHNLS7);
> > > + hdmi_writeb(hdmi, channel_status[4], HDMI_FC_AUDSCHNLS8);
> > > +}
> > > +EXPORT_SYMBOL_GPL(dw_hdmi_set_channel_status);
> > > +
> > >
> > > static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> > >
> > > unsigned long pixel_clk, unsigned int sample_rate)
> > >
> > > {
> > >
> > > diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index
> > > 6988f12d89d9..fcff5059db24 100644
> > > --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > @@ -158,6 +158,8 @@
> > >
> > > #define HDMI_FC_SPDDEVICEINF 0x1062
> > > #define HDMI_FC_AUDSCONF 0x1063
> > > #define HDMI_FC_AUDSSTAT 0x1064
> > >
> > > +#define HDMI_FC_AUDSCHNLS7 0x106e
> > > +#define HDMI_FC_AUDSCHNLS8 0x106f
> > >
> > > #define HDMI_FC_DATACH0FILL 0x1070
> > > #define HDMI_FC_DATACH1FILL 0x1071
> > > #define HDMI_FC_DATACH2FILL 0x1072
> > >
> > > diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
> > > index cf528c289857..4b3e863c4f8a 100644
> > > --- a/include/drm/bridge/dw_hdmi.h
> > > +++ b/include/drm/bridge/dw_hdmi.h
> > > @@ -156,6 +156,7 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool
> > > hpd, bool rx_sense);>
> > > void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
> > > void dw_hdmi_set_channel_count(struct dw_hdmi *hdmi, unsigned int cnt);
> > >
> > > +void dw_hdmi_set_channel_status(struct dw_hdmi *hdmi, u8
> > > *channel_status);
> > >
> > > void dw_hdmi_set_channel_allocation(struct dw_hdmi *hdmi, unsigned int
> > > ca);
> > > void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
> > > void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
> >
> > Looks fine for me:
> > Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> >
> > Jonas ? Jernej ? Russell ?
>
> Patch itself is fine, I'm just wondering if more information should be copied
> from status array to registers. But I think they are not 1:1 mapping so some
> more work would be needed. Anyway, patch is:

Hi Jernej,
Yes you are right. I was thinking about the same thing.
But there are also some fields in the IEC60958 spec not mapped to the
registers on dw-hdmi.
So I ended up just writing the two registers in the original ykk's
patch, and ignoring "original sampling frequency" like pcm_iec958.
It turns out that audio plays fine on my LG monitor. So I suggest we
can keep this patch as simple as it is, and add more register setting
if we find issue.
Thanks!

>
>
> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
>
> Best regards,
> Jernej
>
> >
> > If it's ok for you I'll apply it.
> >
> > Neil
>
>
>
>

\
 
 \ /
  Last update: 2019-09-11 19:04    [W:0.148 / U:3.388 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site