lkml.org 
[lkml]   [2019]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] dt-bindings: gpio: Add binding document for xylon logicvc-gpio
Date
The Xylon LogiCVC display controller exports some GPIOs, which are
exposed as a dedicated driver.

This introduces the associated device-tree bindings documentation.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
.../bindings/gpio/xylon,logicvc-gpio.txt | 48 +++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.txt

diff --git a/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.txt b/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.txt
new file mode 100644
index 000000000000..4835659cb90b
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.txt
@@ -0,0 +1,48 @@
+Xylon LogiCVC GPIO controller
+
+The Xylon LogiCVC is a display controller that contains a number of GPIO pins,
+meant to be used for controlling display-related signals.
+
+In practice, the GPIOs can be used for any purpose they might be needed for.
+
+The controller exposes GPIOs from the display and power control registers,
+which are mapped by the driver as follows:
+- GPIO[4:0] (display control) mapped to index 0-4
+- EN_BLIGHT (power control) mapped to index 5
+- EN_VDD (power control) mapped to index 6
+- EN_VEE (power control) mapped to index 7
+- V_EN (power control) mapped to index 8
+
+The driver was implemented and tested for version 3.02.a of the controller,
+but should be compatible with version 4 as well.
+
+Required properties:
+- compatible: Should contain "xylon,logicvc-3.02.a-gpio".
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be 2. The first cell is the pin number and
+ the second cell is used to specify the gpio polarity:
+ 0 = Active high,
+ 1 = Active low.
+- gpio,syscon-dev: Syscon phandle representing the logicvc instance.
+
+Example:
+
+ logicvc: logicvc@43c00000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x43c00000 0x6000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ logicvc_gpio: display-gpio@40 {
+ compatible = "xylon,logicvc-3.02.a-gpio";
+ reg = <0x40 0x40>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio,syscon-dev = <&logicvc>;
+ };
+ };
+
+Note: the device-tree node should either be declared as a child of the logicvc
+syscon node or the syscon node should be precised with the gpio,syscon-dev
+property. Both are shown in the example above.
--
2.23.0
\
 
 \ /
  Last update: 2019-09-10 17:30    [W:1.611 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site